Quick Start Instructions

Size: px

Start display at page:

Download "Quick Start Instructions"

Kimberly Oliver
6 years ago
Views:

1 Eaton Power Xpert Gateway Minisot (PXGMS) UPS Card Quick Start Instructions Ethernet 10/100 Status DHCP EMP + - CMN 100 Act Ident Power PXGMS UPS Restart TX Setup RX Package Contents Power Xpert Gateway Minisot (PXGMS) UPS Card USB Cabe Quick Start Instructions

2 Hep Desk Numbers United States or Canada ext 260 A Other Countries Ca your oca service representative Web Site NOTE: On the Web site opening page, cick Support and seect the Customer Service ink for more information. Eaton, Power Xpert, and PredictPuse are registered trademarks of Eaton Corporation or its subsidiaries and affiiates. Googe Chrome is a trademark of Googe Inc. Linux is a registered trademark of Linus Torvads. Microsoft, Internet Exporer, and Windows are registered trademarks of Microsoft Corporation in the United States and in other countries. Mozia and Firefox are registered trademarks of the Mozia Foundation. A other trademarks are property of their respective companies. Copyright 2015 Eaton Corporation, Raeigh, NC, USA. A rights reserved. No part of this document may be reproduced in any way without the express written approva of Eaton Corporation.

3 TABLE OF CONTENTS Section 1 Instaation Checkist... 2 Section 2 Insta the Card... 3 Section 3 Connect the Card to the Computer... 5 Section 4 Insta the USB Driver Software... 7 Section 5 Obtain a DHCP-Assigned IP Address Section 6 Assign an IP Address Manuay Section 7 Disabe Browser Compatibiity Mode Section 8 Register a PredictPuse Subscription Eaton PXGMS Card Quick Start Instructions P Rev 2 1

4 Section 1 Instaation Checkist 1. Verify that the foowing items are avaiabe: o Power Xpert Gateway Minisot (PXGMS) UPS Card package contents (card, cabe, Quick Start Instructions) o Phiips screwdriver o Avaiabe USB port on a computer running Microsoft Windows o Web browser (Microsoft Internet Exporer version 8.0 and higher, Mozia Firefox, or Googe Chrome are recommended) 2. If you are going to use Dynamic Host Configuration Protoco (DHCP), provide your oca network administrator with the card's MAC address. The MAC address is ocated on either the shipping box abe or the abe on this card. o MAC Address 3. If you are not going to use DHCP to provide any of the settings isted beow, contact your oca network administrator for the settings. In the tabe beow, check the DHCP check box or enter the vaues for manua configuration.you wi reference this data ater in the procedure. Item DHCP* Manua Configuration IPv4 o Card IP Address: Netmask: Gateway: DNS Name Servers o Name Server #1: Name Server #2: Name Server #3: DNS Domain o Domain: * The network administrator normay sets up the DHCP server to provide a static IP address each time the card makes a DHCP request. 4. If you need e-mai functionaity, obtain the SMTP mai server's IP address or host name. If using the SMTP host name, verify that you aso have the Name Server IP address (see Step 3). o SMTP (mai server) IP Address or Host Name 2 Eaton PXGMS Card Quick Start Instructions P Rev 2

5 Status DHCP Setup Section 2 Insta the Card The hot-swappabe PXGMS card can be instaed without turning off the UPS or disconnecting the oad. If your UPS is a 93PM, there may be a meta strip that prevents you from instaing the PXGMS card. If so, ocate the meta strip boted to the top of the UPS. Remove the three bots that attach the meta strip. Then, foow the procedure to insta the PXGMS card. To insta the PXGMS card: 1. On the PXGMS card, verify that a six DIP switches are in the OFF position (see Figure 1). ON OFF Ethernet 10/ EMP Act Ident Power + - CMN PXGMS UPS Restart TX RX Figure 1. Verify DIP Switches are OFF 2. If not aready done, record the MAC address from either the shipping box abe or the abe on this card for future reference (see the "Instaation Checkist" on page 2). 3. Remove the minisot cover from the UPS. Retain the screws. If another card is aready instaed with an attached communication cabe, disconnect the cabe and then remove the card. 4. To prevent eectrostatic discharge (ESD), pace one hand on a meta surface, such as the UPS rear pane. Eaton PXGMS Card Quick Start Instructions P Rev 2 3

6 5. Side the card into the open sot and secure it with the screws removed in Step 2 (see Figure 2). Ethernet 10/100 Status DHCP EMP + - CMN 100 Act Ident Power PXGMS UPS Restart TX Setup RX Figure 2. Secure the PXGMS Card 6. From your aptop, go to 7. On the Features tab, cick the Downoad Configuration Fie ink to downoad the configuration fie. 8. Save the driver configuration fie (powerxpert.inf) to the C: drive using the defaut ocation or a foder you seect. Note the path of the downoaded fie on your computer. (Never downoad the fie to your desktop.) 4 Eaton PXGMS Card Quick Start Instructions P Rev 2

7 Section 3 Connect the Card to the Computer To connect the card to the computer: 1. Pug the sma connector at the end of the suppied USB configuration cabe into the setup port on the card (see Figure 3). Ethernet 10/100 Status DHCP EMP + - CMN 100 Act Ident Power PXGMS UPS Restart TX Setup RX Figure 3. Insta the USB Cabe 2. Pug the other end of the USB cabe into the USB port on the computer. The Windows operating system detects new hardware. If a message indicates that the device driver software was not successfuy instaed, cick Ignore. You may see a pop-up message window that shows Found new hardware. This indicates that the hardware instaed successfuy. Eaton PXGMS Card Quick Start Instructions P Rev 2 5

8 3. Connect an active Ethernet cabe (not suppied) to the Ethernet 10/100 connector on the PXGMS card (see Figure 4). Ethernet 10/100 Status DHCP EMP + - CMN 100 Act Ident Power PXGMS UPS Restart TX Setup RX Figure 4. Insta the Ethernet Cabe 4. Wait for the power ight and status ight on the instaed card to iuminate. This takes about two minutes. 5. Open a Web browser and type the defaut IP address ( ). 6. Did the Power Xpert Gateway software open to the PXGMS page? If yes, the driver has aready been instaed automaticay. Either verify the IP address assigned through DHCP or manuay enter a static (fixed) IP address for the card s network connection: a.to verify the DHCP-assigned IP address, go to page 13. b.to manuay enter a fixed IP address, go to page 16. If no, the driver has not been instaed. Go to the next section, "Insta the USB Driver Software" on page 7 in order to confirm that you have the most current USB Driver software. If not, you need to insta or update the USB Driver software. 6 Eaton PXGMS Card Quick Start Instructions P Rev 2

9 Section 4 Insta the USB Driver Software The steps you use to insta the driver software depend on your operating system (OS). This procedure provides instructions for instaing driver software on a Windows 7 OS. Windows 8 steps are basicay the same as Windows 7, athough the diaog dispays may differ somewhat. The PXGMS and PXGX UPS cards use the same driver. You can use either the Device Manager path or the Devices and Printers path to browse for the driver software and insta it. This procedure uses the Device Manager. To insta the driver from the Device Manager: 1. Cick Start in the Start bar. Type Device in the search box. 2. Seect Device Manager from the ist above the search box. The Device Manager opens. 3. Locate RNDIS/Ethernet Gadget under either Other Devices or Network Adapters (see Figure 5). If you do not see RNDIS/Ethernet Gadget in either ist, you do not have a cabe connected to the card. Connect the computer to the card. Go back to Step 1. If RNDIS/Ethernet Gadget is isted under Other Devices, the driver is not instaed. Go to Step 4. If RNDIS/Ethernet Gadget is isted under Network Adapters, a driver is instaed aready, but you it may not be the most up to date driver. Go to Step 4. Eaton PXGMS Card Quick Start Instructions P Rev 2 7

If a pop-up message dispays, The best driver is aready instaed, cick Cose and go to Step 10.

10 Figure 5. Device Manager Window 4. Right-cick RNDIS/Ethernet Gadget to dispay the menu and seect Update Driver Software. If a pop-up message dispays, The best driver is aready instaed, cick Cose and go to Step 10. Otherwise, go to Step Seect Browse my computer for driver software (see Figure 6). Cick Next. The next page dispays. Figure 6. Update Driver Software Window Search Method 8 Eaton PXGMS Card Quick Start Instructions P Rev 2

6. Cick Browse. The Browse for Foder diaog dispays. Seect the foder that contains drivers for your hardware. Cick OK. The Browse for driver software on your computer page dispays. 7.

11 6. Cick Browse. The Browse for Foder diaog dispays. Seect the foder that contains drivers for your hardware. Cick OK. The Browse for driver software on your computer page dispays. 7. The path to the powerxpert.inf fie dispays in the Search for driver software in this ocation box. Cick Browse and navigate to the powerxpert.inf fie you aready downoaded. Seect the fie and cick Next (see Figure 7). If a pop-up message dispays, The best driver is aready instaed, cick Cose and go to Step 10. Otherwise, the software begins to insta. Figure 7. Update Driver Software Window Browse for Driver Software If the message Windows can't verify the pubisher of this driver software dispays, seect Insta this driver software anyway (see Figure 8). Eaton PXGMS Card Quick Start Instructions P Rev 2 9

Figure 8. Windows Security Message 8. When the driver software is updated successfuy, the message Windows has successfuy updated your driver software dispays (see Figure 9).

Either obtain the DHCP-assigned IP address or manuay enter a fixed IP address: To obtain the IP address assigned through DHCP, continue to "Obtain a DHCP-Assigned IP Address" on

12 Figure 8. Windows Security Message 8. When the driver software is updated successfuy, the message Windows has successfuy updated your driver software dispays (see Figure 9). Figure 9. Update Driver Software Window Update Successfu 9. Cick Cose. 10. Either obtain the DHCP-assigned IP address or manuay enter a fixed IP address: To obtain the IP address assigned through DHCP, continue to "Obtain a DHCP-Assigned IP Address" on page 11. To manuay enter a static (fixed) IP address for the card s network connection, continue to "Assign an IP Address Manuay" on page 15. By defaut, the PXGMS card requests an IP address through DHCP when connected to a network. 10 Eaton PXGMS Card Quick Start Instructions P Rev 2

13 Section 5 Obtain a DHCP-Assigned IP Address To obtain the IP address through DHCP: 1. Ensure the PXGMS card is sti connected to the computer over the USB cabe. Aso ensure that the network cabe is connected from the PXGMS card Ethernet port to the network connection. 2. If your Web browser aready open to the defaut IP address, go to Step 3. Otherwise, perform the foowing: Open your Web browser. Enter: Log on as administrator. The defaut username and defaut password are admin. The PXGMS card Web page dispays. If the system is unresponsive and you cannot make any seections, the browser may be running in compatibiity mode. To disabe compatibiity mode, go to "Disabe Browser Compatibiity Mode" on page Seect Network from the Configuration menu. The Network page dispays (see Figure 10). Eaton PXGMS Card Quick Start Instructions P Rev 2 11

Figure 10. PXGMS Card Network Page 4. Under IPv4, the Automatic Configuration: DHCP Enabed setting checkbox shoud be enabed by defaut. Make sure the checkbox is checked (enabed) before continuing. 5.

14 Figure 10. PXGMS Card Network Page 4. Under IPv4, the Automatic Configuration: DHCP Enabed setting checkbox shoud be enabed by defaut. Make sure the checkbox is checked (enabed) before continuing. 5. Scro down to Name Service and expand the seection to update the next two DHCP settings (see Figure 11): Check the checkbox (enabe) for Use DHCP (when enabed) to get name services. Check the checkbox (enabe) for Use DHCP (when enabed) to get domain name. 12 Eaton PXGMS Card Quick Start Instructions P Rev 2

6. Cick Appy. Figure 11. Name Services Settings 7. Seect Yes for the message, Do you want to save the Network Configuration? 8. Wait for approximatey two minutes for the card to reboot.

15 6. Cick Appy. Figure 11. Name Services Settings 7. Seect Yes for the message, Do you want to save the Network Configuration? 8. Wait for approximatey two minutes for the card to reboot. Initiay, a ights wi be it. You wi know the card has finished rebooting when ony the top ight (Status) and the bottom ight (Power) remain it. Eaton PXGMS Card Quick Start Instructions P Rev 2 13

16 9. Open a browser and enter the defaut IP address ( ). 10. When prompted, og on as administrator. The defaut username and defaut password are admin. The PXGMS card Web page dispays. 11. Cick Network in the menu ist. 12. Does the DHCP-assigned IP address dispay? If yes, uncheck (disabe) the DHCP Enabed box and seect Appy. At this point, the DHCP address is saved as a static IP address. If no, go to "Assign an IP Address Manuay" on page 15 to manuay obtain a static IP address for the PXGMS card. For detaied information, refer to the user s guide for the Eaton Power Xpert Gateway Minisot (PXGMS) User s Guide, which is avaiabe through a ink on the Documentation tab on the PXGMS product Web page. 14 Eaton PXGMS Card Quick Start Instructions P Rev 2

17 Section 6 Assign an IP Address Manuay To manuay enter a static (fixed) IP address for the card: 1. Ensure the PXGMS card is sti connected over the USB cabe and the network cabe is connected from the PXGMS card Ethernet port to the network connection. 2. If your Web browser aready open, go to Step 3. Otherwise, perform the foowing: Open your Web browser. Enter: Log on as administrator. The defaut username and defaut password are admin. The PXGMS card Web page dispays. Go to Step 3. If the system is unresponsive and you cannot make any seections, the browser may be running in compatibiity mode. To disabe compatibiity mode, go to "Disabe Browser Compatibiity Mode" on page Seect Network from the Configuration menu. The Network page dispays. Eaton PXGMS Card Quick Start Instructions P Rev 2 15

18 Figure 12. Disabe DHCP Setting 4. Uncheck the DHCP Enabed checkbox to disabe DHCP and aow you to manuay configure the IP address (see Figure 12). 5. Refer to the "Instaation Checkist" on page 2 in this book. Enter the IP address, Netmask, and Gateway addresses in the IPv4 > Manua Configuration section. 6. Cick Appy, then cick OK to confirm. 7. Optiona. If you are using a host name, or host names, for controing access to the card: Type the server IP address in the Name Server box. (Up to three IP addresses can be entered.) Cick Appy. Cick OK to confirm. 16 Eaton PXGMS Card Quick Start Instructions P Rev 2

19 8. Open a browser and enter the fixed (static) IP address. 9. Log on as administrator. The defaut username and defaut password are admin. When the PXGMS card Web page dispays, you know the fixed IP Address is working. For detaied information, refer to the user s guide for the Eaton Power Xpert Gateway Minisot (PXGMS) User s Guide, which is avaiabe through a ink on the Documentation tab on the PXGMS product Web page. Eaton PXGMS Card Quick Start Instructions P Rev 2 17

20 Section 7 Disabe Browser Compatibiity Mode Browser compatibiity aows Web pages designed for oder versions to dispay propery. If data does not dispay propery on your PXGMS card Web page, the browser compatibiity mode shoud be disabed. To disabe the compatibiity mode: 1. Open your Web browser. 2. In the Menu bar seect Toos > Compatibiity View Settings. The Compatibiity View Settings window opens (see Figure 13). Figure 13. Compatibiity View Settings Window 18 Eaton PXGMS Card Quick Start Instructions P Rev 2

21 3. Uncheck (disabe) the Dispay a websites in Compatibiity View checkbox to disabe compatibiity mode and cick Cose. Cose and re-open your browser so that the changes take effect. Eaton PXGMS Card Quick Start Instructions P Rev 2 19

22 Section 8 Register a PredictPuse Subscription PredictPuse is a remote monitoring and management subscription service that coects and anayzes data from connected power infrastructure devices, providing Eaton with the insight needed to make recommendations and take action on your behaf. This service has imited avaiabiity outside of the United States. For more information go to Contact your Eaton service representative for avaiabiity of PredictPuse in your region. Use either the universa PredictPuse Subscription Wizard or the PXGMS PredictPuse setup feature to configure your profie and register the Eaton UPS devices monitored by PredictPuse. The universa PredictPuse Wizard can be downoaded from the PredictPuse web site to begin your subscription registration. Using this method, you can register devices individuay or as a group. However, the atest firmware for the PXGMS and PXGX UPS cards contain a PredictPuse activation set-up feature. As ong as these cards are on your network, you can quicky activate subscriptions without the wizard and save time. To begin registering with the set-up feature, foow this procedure. An e-mai with additiona instructions to finish registering and configuring your card is automaticay sent to the provided e-mai address. To register an instaed PXGMS card for PredictPuse: 1. Locate the PredictPuse seection under the Configuration menu on the Power Xpert Gateway window. If there isn't a PredictPuse seection, either update your firmware or downoad the universa PredictPuse Wizard from and foow the instructions in the Wizard and subsequent e-mai messages. Refer to the Eaton Power Xpert Gateway Minisot (PXGMS) User s Guide for more information. 20 Eaton PXGMS Card Quick Start Instructions P Rev 2

23 2. On the Power Xpert Gateway window, seect Configuration > PredictPuse (see Figure 14). Figure 14. Registering a PredictPuse Subscription 3. Confirm that the checkbox for Enabe PredictPuse is checked (enabed). 4. Compete the foowing fieds: Contact Name: First and ast name of the contact person. Contact Emai: E-mai address of the contact person for event data. Confirm Emai: E-mai address again for confirmation. Country: Country where the main contact resides. 5. Cick Appy to save. 6. Cick OK in response to the message, Are you sure you want to appy settings and send registration emai? Eaton PXGMS Card Quick Start Instructions P Rev 2 21

24 7. A progress message box informs you that registration is in progress. When the first step in registration competes successfuy, the contact person identified on the PredictPuse settings page wi receive an e-mai with additiona instructions (see Figure 15). Registration shoud be competed on the Eaton porta by this contact person. Figure 15. Confirmation Message 22 Eaton PXGMS Card Quick Start Instructions P Rev 2

26 P

Quick Start Instructions

Eaton Power Xpert Gateway Minislot (PXGMS) UPS Card Quick Start Instructions Package Contents l Power Xpert Gateway Minislot (PXGMS) UPS Card l l USB Cable Quick Start Instructions Help Desk Numbers United