ivizion Series Next-Generation Banknote Acceptor Unit

Transcription

1 Support: We-Site: ivizion Series Next-Genertion Bnknote Acceptor Unit Opertion nd Mintennce Mnul (Revision 3) Issue #4074-SME-01-03

2 ivizion Series Next-Genertion Bnknote Acceptor Unit Opertion nd Mintennce Mnul Issue #4074-SME REVISION HISTORY Rev. Dte Reson for Updte Comment A Initil Version Section 7 Prts List Numer Chnges incorported. Engineering dictted chnges Additionl Section 7 Prts List Numer Chnges incorported nd LD Version informtion dded. Added Specifictions, instlltion informtion nd Grphics regrding the ivizion LD Version Unit. Engineering dictted chnges Engineering dictted chnges Interntionl Complince RoHS Directives UL & c-ul Mrks or or or File No. E142330, Suscrier , Vo.2 CE Mrk CB Scheme NO58326 FCC & IC Directives See Below. Contins Trnsmitter Module FCC ID: VZQNRWA3 MODEL NO.: NRWA3 IC: 8285A-NRWA3 This device complies with Prt 15 of FCC Rules nd RSS-Gen of IC Rules. Opertion is suject to the following two conditions: (1) this device my not cuse interference, nd (2) this device must ccept ny interference, including interference tht my cuse undesired opertion of this device. FCC WARNING Chnges or modifictions not expressly pproved y the prty responsile for complince could void the user s uthority to operte the equipment. FCC NOTICE This equipment hs een tested nd found to comply with the limits for Clss A digitl device, pursunt to prt 15 of the FCC Rules. These limits re designed to provide resonle protection ginst hrmful interference when the equipment is operted in commercil environment. This equipment genertes, uses nd cn rdite rdio frequency energy nd, if not instlled nd used in ccordnce with the instructions, my cuse hrmful interference to rdio communictions. Opertion of this equipment in residentil re is likely to cuse hrmful interference in which cse the user will e required to correct the interference t his own expense. IC NOTICE This clss A digitl pprtus complies with Cndin ICES-003. Cet ppreil numerique de l clsse A est conforme l norme NMB-003 du Cnd. Copyright 2012 By Jpn CshMchine Co, Limited This product document (hereinfter referred to s Mnul ) is fully covered y legl Copyrights owned y the Jpn Csh Mchine, Co., Ltd., (hereinfter referred to s JCM ) under Jpnese lws nd other Foreign Countries. This Mnul contins mny copyrighted, ptented or properly registered equipment items mnufctured y JCM, tht re prohiited nd illegl to duplicte, replicte, copy in whole, or in prt, without the express uthoriztion y JCM with the following exceptions: 1. When n uthorized JCM gency or distriutor duplictes the Mnul for sles promotion nd/or service mintennce of the product, or technicl service personnel eduction s required; nd 2. When n end user duplictes the Mnul to mintin opertion of the product or operte the product in generl. JCM retins ll rights to mend, lter, chnge or delete ny portion of this Mnul in whole, or in prt, or dd items thereto without notice regrding the product or its relted products. JCM is registered trdemrk of Jpn CshMchine Co, Limited. All other product nmes mentioned herein my e registered trdemrks or trdemrks of their respective compnies. Furthermore,, nd re not lwys mentioned in ech cse throughout this puliction.

3 ivizion Series Next-Genertion Bnknote Acceptor Unit Tle of Contents TOC 1 GENERAL INFORMATION Description ivizion Units Model Numer Specifictions Type Descriptions Softwre Descriptions Precutions User Cutions Instlltion Cutions Mounting, Dismounting & Trnsporttion Preventive Mintennce Bnknote Fitness Requirements Reference Pper Use Precutions Primry Fetures Component Nmes Specifiction (ivizion SS Version) Technicl Specifictions Environmentl Specifictions Electricl Specifictions Structurl Specifictions Specifiction (ivizion LD Version) Technicl Specifictions Environmentl Specifictions Electricl Specifictions Structurl Specifictions ivizion Entire Unit Outside Dimensions ivizion SS Version Instlltion/Mintennce Spce Requirements ivizion LD Specifiction Unit Dimensions Vrious Csh Box Unit Dimensions Stndrd Csh Box Outside Dimensions Lrge Csh Box Outside Dimensions Interntionl Complince Technicl Contct Informtion Americs & Oceni JCM Americn Europe, Afric, Russi & Middle Est JCM Europe GmH UK & Irelnd JCM Europe (UK Office) Asi JCM Gold (HK) Ltd Jpn Csh Mchine Co, Limited (HQ) INSTALLATION Instlltion Process Pge i

4 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Tle of Contents Cle Interconnection DIP Switch Configurtions Primry LED Indictions Connector Pin Assignments Connector Pin Assignments (Continued 1) Connector Pin Assignments (Continued 2) Connector Pin Assignments (Continued 3) Connector Pin Assignments (Continued 4) Connector Pin Assignments (Continued 5) Preventive Mintennce Retrieving Bnknotes Clering Bnknote Jm Clening Procedure Sensor Clening Procedure ivizion Optionl LD Version Unit Instlltion ivizion Sensor Loctions Stndrd Interfce Circuit Schemtics Interfce Circuit Schemtics (Continued 1) Interfce Circuit Schemtics (Continued 2) Interfce Circuit Schemtics (Continued 3) Opertionl Flowchrt Opertionl Flowchrt (Continued 1) Opertionl Flowchrt (Continued 2) COMMUNICATIONS Americs & Oceni JCM Americn Europe, Afric, Russi & Middle Est JCM Europe GmH UK & Irelnd JCM Europe (UK Office) Asi JCM Gold (HK) Ltd Jpn Csh Mchine Co, Limited (HQ) DISASSEMBLY/REASSEMBLY Tool Requirements Pusher Unit Timing Belt Removl Home Position Sensor Bord/Home Position Sensor, FFC & Interfce Connector Bord Removls RFID Module & Hrness Removls Vlidtion CPU & Controller CPU Bord Removls USB FPC, Power FPC & Interfce FPC Cle Removls Vlidtion Unit Hrness Removl Interrupter Bord Removl Motor Unit Timing Belt Removl Stcker Motor & Trnsport Motor Removls Bezel Retiner Clips A & B Removl Pge ii

5 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Tle of Contents Sensor Trnsfer Bord/CIS FFC/Trnsmissive Light FFC & Upper UV FPC Sensor Removls Vlidtion Sensor Bord Assemly Removl Vlidtion Sensor FPC Cle Removls CIS/Trnsmissive Light & Upper UV Sensor Removls CIS/CIS FPC/Lower UV Sensor & Lower UV FFC Removl Vlidtion Unit Timing Belt Removl Ressemly Cutions WIRING DIAGRAMS ivizion System Wiring Digrm CALIBRATION AND TESTING Downlod nd Instlltion Workench Tool Requirements Appliction Softwre Instlltion Driver Instlltion Procedure JCM Tool Suite Stndrd Edition Mode Softwre Downlod Tool Requirements Softwre Downlod Procedures Downlod the Upgrde Progrm Downloding the Progrm First Time Clirtion When to Clirte Clirtion Order Clirtion Tool Requirements Plcing the KS-072 Reference Pper Clirtion Procedure Clirtion Only Clirtion Plus Seril Numer Writing Performnce Tests Performnce Test Tool Requirement using PC Performnce Test Items using PC PC Performnce Test Preprtion Performnce Test Procedures Any Motor Test LED Indictor Test Sensor ON/OFF Test Bnknote Acceptnce Test ICB Function Setting (Brcode Coupon) DIP Switch ON/OFF Test Performnce Test Tool Requirement using n Externl DIP Switch Box Externl DIP Switch Performnce Test Procedure Settings Performnce Tests using the Externl DIP Switch Procedures ivizion Utility Tools ICB/Imge Setting Tool Requirements ICB/Imge Setting Chnge Preprtion CIS Imge Tool ICB Function Setting Setting ICB Enle/Disle Functions Pge iii

6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Tle of Contents ICB Function Opertionl Condition EXPLODED VIEWS & PARTS LISTS ivizion Entire Unit Exploded View ivizion Entire Unit Prts List ivizion Vlidtion Unit 1 Exploded View ivizion Vlidtion Unit 1 Prts List ivizion Vlidtion Unit 2 Exploded View ivizion Vlidtion Unit 2 Prts List ivizion Vlidtion Unit 3 Exploded View ivizion Vlidtion Unit 3 Prts List ivizion Trnsport Unit 1 Exploded View ivizion Trnsport Unit 1 Prts List ivizion Trnsport Unit 2 Exploded View ivizion Trnsport Unit 2 Prts List ivizion Trnsport Unit 3 Exploded View ivizion Trnsport Unit 3 Prts List ivizion Trnsport Unit 4 Exploded View ivizion Trnsport Unit 4 Prts List ivizion Trnsport Unit 5 Exploded View ivizion Trnsport Unit 5 Prts List ivizion Trnsport Unit 6 Exploded View ivizion Trnsport Unit 6 Prts List ivizion SS Version Frme Unit Exploded View ivizion SS Version Frme Unit Prts List ivizion Csh Box Unit 1 Exploded View ivizion Csh Box Unit 1 Prts List ivizion Csh Box Unit 2 Exploded View ivizion Csh Box Unit 2 Prts List ivizion Csh Box Unit 3 Exploded View ivizion Csh Box Unit 3 Prts List ivizion LD Version Frme Exploded View ivizion LD Version Frme Prts List ivizion Optionl Components Exploded Views ivizion Optionl Components Prts List INDEX A TROUBLESHOOTING... A-1 Introduction...A-1 Trouleshooting Overview...A-1 Mlfunction LED Error Codes...A-1 LED Indiction Conditions...A-1 Error, Jm nd Reject Code Tles...A-2 Jm Error Codes...A-4 Reject Error Code...A-5 Mintennce Equipment...A-6 ivizion Mintennce Equipment...A-6 Reference Pper Hndling...A-6 B GLOSSARY... B-1 Pge iv

7 LOF ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures Figure 1-1 ivizion Units Figure 1-2 Precutionry Symols Figure 1-3 Uncceptle Bnknotes Figure 1-4 KS-072 Reference Pper Hndling Precutions Figure 1-5 ivizion Component Nmes Figure 1-6 ivizion Bnknote Acceptor SS Version Unit Outside Dimensions Figure 1-7 ivizion SS Version Unit Instlltion nd Mintennce Spce Requirements Digrm Figure 1-8 Mximum Grdient Angle = 50 Degrees Figure 1-9 ivizion LD Version Unit Outside Dimensions Figure 1-10 ivizion LD Version Unit with Bezel Outside Dimensions Figure 1-11 ivizion Stndrd Csh Box Outside Dimensions Figure 1-12 ivizion Lrge Csh Box Outside Dimensions Figure 2-1 Interfce Hrness Instlltion Loction Figure 2-2 M4 Screws Loctions (Left/Right Side) Figure 2-3 Flt Hed Screws Loctions (Rer Side) Figure 2-4 Cle Interconnection Figure 2-5 Retrieving Bnknote Figure 2-6 Open the Upper Guides Figure 2-7 Retrieving Csh Box Bnknote Jm Figure 2-8 Interfce Hrness Instlltion Loction Figure 2-9 M3 Screws Loctions Figure 2-10 ivizion Sensor Clening Loctions Figure 2-11 ivizion USB Circuit Interfce Schemtic Digrm Figure 2-12 ivizion Photo-Coupler Circuit Interfce Schemtic Digrm Figure 2-13 ivizion RS232C Circuit Interfce Schemtic Digrm Figure 2-14 ivizion cctlk Circuit Interfce Schemtic Digrm Figure 2-15 ivizion TTL Circuit Interfce Schemtic Digrm Figure 2-16 ivizion LED Circuit Interfce Schemtic Digrm Figure 2-17 ivizion SS/LD Bnknote Acceptor Opertionl Flowchrt (Prt 1 - Initilizing) Figure 2-18 ivizion SS Bnknote Acceptor Opertionl Flowchrt (Prt 2 - Vlidting) Figure 2-19 ivizion LD Bnknote Acceptor Opertionl Flowchrt (Prt 2 - Vlidting) Figure 4-1 Pusher Mechnism Screws Removl Figure 4-2 Pusher Mechnism Removl Figure 4-3 Pusher Mechnism Cover Removl Figure 4-4 Stcker Guide Removl Figure 4-5 Stcker Guide Ressemly Pge v

8 ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures Figure 4-6 Right Frme Outer R Removl Figure 4-7 Left Frme Outer L Removl Figure 4-8 Timing Belt Removl Figure 4-9 TR Bottom Cover Removl Figure 4-10 TR Side Cover A Removl Figure 4-11 Home Position Sensor Bord, Home Position Sensor FFC Assemly nd Interfce Connector Bord Removls Figure 4-12 RFID Module & Hrness Removl Figure 4-13 CPU Bord Module Removl Figure 4-14 Extension Memory Bord Removl Figure 4-15 Vlidtion CPU Bord nd Control CPU Bord Removl Figure 4-16 Motor Module Removl Figure 4-17 USB FPC, Power FPC & Interfce FPC Cle Removl Figure 4-18 Vlidtion Unit Hrness Removl Figure 4-19 Interrupter Bord Removl Figure 4-20 Timing Belt Removl Figure 4-21 Timing Belt Ressemly Pth Figure 4-22 Stcker & Trnsport Motor Removl Figure 4-23 Bezel Retiner Chips A&B Removl Figure 4-24 Upper Cover Removl Figure 4-25 Sensor Trnsfer Bord Assemly, CIS FFC, Trnsmissive Light & Upper UV FPC Cle Removl Figure 4-26 ivizion Hed Cover A Removl Figure 4-27 Vlidtion Sensor Bord Assemly Removl Figure 4-28 Vlidtion Sensor FPC Removl Figure 4-29 Vlidtion Sensor FPC Ressemly Figure 4-30 Upper Vlidtion Prt Removl Figure 4-31 ivizion Hed BG85B Removl Figure 4-32 CIS, Trnsmissive Light & Upper UV Sensor Removl Figure 4-33 ivizion BG 85A HEAD Removl Figure 4-34 Lower Vlidtion Prt Removl Figure 4-35 CIS, CIS FPC, Lower UV Sensor & Lower UV FFC Removl Figure 4-36 Timing Belt Removl Figure 4-37 Timing Belt Replcement Figure 4-38 Upper/Lower UV Sensors Loction Figure 5-1 ivizion System Wiring Digrm Figure 6-1 Tool nd Hrness Connections Figure 6-2 USB Cle Type Requirement Figure 6-3 Setup.exe File Loction Figure 6-4 Instll Shield Wizrd Screen Figure 6-5 Customer Informtion Screen Figure 6-6 Destintion Folder Screen Figure 6-7 Current Settings Confirmtion Figure 6-8 Instlltion Completion Screen Pge vi

9 ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures Pge Figure 6-9 Hrdwre Updte Wizrd Screen Figure 6-10 Hrdwre Updte Wizrd Screen Figure 6-11 Hrdwre Updte Wizrd Screen Figure 6-12 Hrdwre Updte Wizrd Screen Figure 6-13 Norml Mode Selection Figure 6-14 Test Mode Selection Figure 6-15 Required Softwre Downlod Tools Figure 6-16 DIP Switches All OFF Figure 6-17 JCM Tool Suite Stndrd Edition Screen Figure 6-18 JCM Tool Suite Stndrd Edition Screen Pull-Down Menu Figure 6-19 Browse Screen Button Loction Figure 6-20 ivizion Softwre Progrm Selection Figure 6-21 Downlod Progress Screen Figure 6-22 Downlod Completed Screen Figure 6-23 DIP Switches 6, 7, & 8 ON Figure 6-24 JCM Tool Suite Stndrd Edition Screen Figure 6-25 JCM Tool Suite Stndrd Edition Screen Pull-Down Menu Figure 6-26 Browse Screen Button Loction Figure 6-27 ivizion Softwre Progrm Selection Figure 6-28 Downlod Progress Screen Figure 6-29 Downlod Completed Screen Figure 6-30 Remote Clirtion Tools Required Figure 6-31 Reding KS-072 Reference Pper Figure 6-32 Reference Pper Setting Figure 6-33 Reference Pper Setting Figure 6-34 DIP Switch #8 ON Figure 6-35 JCM Tool Suite Stndrd Edition Screen Figure 6-36 ivizion Clirtion Ver.X.XX Screen Figure 6-37 Feed-Out Clirtion Proceeding Screen Figure 6-38 Clirtion Informtion Screen Figure 6-39 Clirtion Informtion Screen Figure 6-40 Pusher Plte Relese Loction Figure 6-41 Crdord Setting Loction Figure 6-42 Exit Clirtion Proceeding Screen Figure 6-43 Clirtion Informtion Screen Figure 6-44 UV Clirtion Proceeding Screen Figure 6-45 Clirtion Informtion Screen Figure 6-46 Clirtion Informtion Screen Figure 6-47 CIS Clirtion Proceeding Screen Figure 6-48 Clirtion Informtion Screen Figure 6-49 Clirtion Vlue Writing Screen Figure 6-50 Clirtion Complete Screen Figure 6-51 ivizion Clirtion Service Suite Edition Screen Figure 6-52 Setting Mnufcture No. Screen vii

10 ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures Figure 6-53 Clirtion Vlue Writing Screen Figure 6-54 Adjustment Info Screen Figure 6-55 PC Performnce Test Tools Required Figure 6-56 DIP Switch #8 Set ON Figure 6-57 JCM Tool Suite Stndrd Edition Screen Figure 6-58 ivizion Test Item VerX.XX Screen Figure 6-59 Strt, Stop & Exit Screen Button Figure 6-60 Trnsport Motor Norml Forwrd Test Screen Figure 6-61 LED Indictor Test Screen Figure 6-62 Sensor ON/OFF Test Screen Figure 6-63 Denomintion Indiction Loction Figure 6-64 ICB Function Test Screen Figure 6-65 DIP Switch ON/OFF Test Screen Figure 6-66 DIP Switch ON/OFF Test Screen Figure 6-67 Clirtion Tool Requirements Figure 6-68 ICB Setting Tool Requirements Figure 6-69 JCM Tool Suite Stndrd Edition Figure 6-70 ivizion Utility Tool Version X.XX for Suite Edition Screen Figure 6-71 Empty CIS IMAGE Screen Figure 6-72 Lst Acceptnce CIS IMAGE Screen Figure 6-73 ivizion Utility Tool Version X.XX for Suite Edition Screen Figure 6-74 ICB Function Screen Figure 6-75 Enle Setting Completion Figure 6-76 Disle Setting Completion Figure 6-77 ICB Current Sttus Screen Figure 6-78 Mchine Numer Setting Figure 6-79 Mchine Numer Setting Completion Figure 6-80 Mchine Numer Indiction Figure 6-81 Inhiit Screen Button Loction Figure 6-82 Inhiit Setting Completion Figure 6-83 ICB System Sttus Indiction Figure 7-1 ivizion Entire Unit Exploded View Digrm Figure 7-2 ivizion Vlidtion Unit 1 Exploded View Figure 7-3 ivizion Vlidtion Unit 2 Exploded View Figure 7-4 ivizion Vlidtion Unit 3 Exploded View Figure 7-5 ivizion Trnsport Unit 1 Exploded View Figure 7-6 ivizion Trnsport Unit 2 Exploded View Figure 7-7 ivizion Trnsport Unit 3 Exploded View Figure 7-8 ivizion Trnsport Unit 4 Exploded View Figure 7-9 ivizion Trnsport Unit 5 Exploded View Figure 7-10 ivizion Trnsport Unit 6 Exploded View Figure 7-11 ivizion SS Version Frme Unit Exploded View Figure 7-12 ivizion Csh Box Unit 1 Exploded View Figure 7-13 ivizion Csh Box Unit 2 Exploded View Pge viii

11 ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures Figure 7-14 ivizion Csh Box Unit 3 Exploded View Figure 7-15 ivizion LD Version Frme Exploded View Figure 7-16 ivizion Optionl Components Exploded Views Figure A-1 Additionl Mintennce Equipment Requirements...A-6 Pge ix

12 ivizion Series Next-Genertion Bnknote Acceptor Unit List of Figures THIS PAGE INTENTIONALLY LEFT BLANK x

13 LOT ivizion Series Next-Genertion Bnknote Acceptor Unit List of Tles Tle 1-1 ivizion Model Numer Specifictions Tle 1-2 ivizion Type Numer Specifictions Tle 1-3 ivizion Softwre Numer Specifictions Tle 1-4 ivizion SS Version Technicl Specifiction Tle 1-5 ivizion SS Version Environmentl Specifiction Tle 1-6 ivizion SS Version Electricl Specifictions Tle 1-7 ivizion SS Version Structurl Specifictions Tle 1-8 ivizion LD Version Technicl Specifiction Tle 1-9 ivizion LD Version Environmentl Specifiction Tle 1-10 ivizion LD Version Electricl Specifictions Tle 1-11 ivizion LD Version Structurl Specifictions Tle 2-1 Denomintion INHIBIT DIP Switch Settings Tle 2-2 JCM Privte Line DIP Switch Setting Tle 2-3 Softwre DIP Switch Settings Tle 2-4 Seril Communictions DIP Switch Settings Tle 2-5 LED Error Pttern Indictions Tle 2-6 ivizion SS/LD USB Connection Pin Assignments Tle 2-7 ivizion SS/LD Photo-Coupler Connector Pin Assignments Tle 2-8 ivizion SS/LD RS232C Connector Pin Assignments Tle 2-9 ivizion SS/LD cctlk Connector Pin Assignments Tle 2-10 ivizion SS/LD TTL Connector Pin Assignments Tle 2-11 ivizion SS/LD Bezel JPL (CN7) Connection Pin Assignments Tle 2-12 ivizion Sensor Clening Loction Types Tle 6-1 ivizion Sensor Clirtion Order Tle 6-2 PC Performnce Test Items Tle 6-3 LED Indictions for ech condition Tle 6-4 Sensor Actions nd Conditions Tle 6-5 Denomintion Vlution List Tle 6-6 Performnce Test DIP Switch Settings Tle 6-7 ICB Setting Function Opertionl Condition Tle 7-1 ivizion Entire Unit Prts List Tle 7-2 ivizion Vlidtion Unit 1 Prts List Tle 7-3 ivizion Vlidtion Unit 2 Prts List Tle 7-4 ivizion Vlidtion Unit 3 Prts List Tle 7-5 ivizion Trnsport Unit 1 Prts List Pge xi

14 ivizion SeriesNext-Genertion Bnknote Acceptor Unit List of Tles Pge Tle 7-6 ivizion Trnsport Unit 2 Prts List Tle 7-7 ivizion Trnsport Unit 3 Prts List Tle 7-8 ivizion Trnsport Unit 4 Prts List Tle 7-9 ivizion Trnsport Unit 5 Prts List Tle 7-10 ivizion Trnsport Unit 6 Prts List Tle 7-11 ivizion SS Version Frme Unit Prts List Tle 7-12 ivizion Csh Box Unit 1 Prts List Tle 7-13 ivizion Csh Box Unit 2 Prts List Tle 7-14 ivizion Csh Box Unit 3 Prts List Tle 7-15 ivizion LD Version Frme Prts List Tle 7-16 ivizion Optionl Components Prts List Tle A-1 LED Code Condition... A-1 Tle A-2 LED Error Codes... A-2 Tle A-3 Jm LED Flsh Error Codes... A-4 Tle A-4 LED Reject Codes... A-5 Tle A-5 Additionl Mintennce Equipment Prts List... A-6 xii

15 ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 1 GENERAL INFORMATION Description This section provides generl overview of the ivizion Next-Genertion Bnknote Acceptor Series pictured in Figure 1-1. This first section is designed to help you nvigte through this guide with ese nd provides the following informtion: ivizion Unit Component Nmes Primry Fetures Model Description Type Description Softwre Description Precutions Specifictions ivizion Units Unit Dimensions Interntionl Complince Technicl Contct Informtion. In order to mke opertion of this device esier nd mke nvigtion within this mnul simpler, the following illustrtions were used within the text: Sfety Instructions, which need to e oserved in order to protect the opertors nd equipment, hve een written in old text nd hve een given the pictogrphs: Specil Notes, which effect the use of the Bnknote Acceptor, hve een written in itlic text nd hve een given the pictogrph: Steps, requiring the opertor to perform specific ctions re given sequentil numers (1., 2., 3., etc). ivizion (LD Version) ivizion (SS Version) Figure 1-1 ivizion Units 1-1

16 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion Model Numer Specifictions Tle 1-1 lists the ivizion Model Numer Descriptions. Tle 1-1 ivizion Model Numer Specifictions N o (1) (2) (3) (4) Model: ivizion - * * * - SS Vlidtion Hed 1: Stndrd 2-9: Reserved N o (1)(2)(3) (4) CPU Bord (Memory) 0: Stndrd 1-9: Reserved Trnsport Unit Type 0: Stndrd 1-9: Reserved Stcker Type SS: Security Stcker Down LD: Less Down (No Stcker) Type Descriptions Tle 1-2 lists the ivizion Type Numer Descriptions. Tle 1-2 ivizion Type Numer Specifictions N o Type: * * * * * * * * N o ()()(c) (d) (e)(f)(g)(h)(i) Box Cpcity * () 5: 500 notes (New Bnknote) 9: 900 notes (New Bnknote) 0: No Csh Box () Box Type 0: Stndrd (c) Box Hndle 0: Stndrd (d) (e) (f) (g) (h) (d) Trnsport Unit Type 00: Stndrd Bezel (Option) 0: Without Bezel 1: With LED Bezel (UBA Stndrd 85) ICB (RFID Type) 0: None 1: ICB-Complint (Stndrd) (for SS Version Only) Optionl Bord (Memory) 0: Stndrd Memory (64M Bit) 1: Memory Extension Bord (128M it) 2: Memory Extension Bord (192M it) Input/Output Signl Selection P: Photo-Coupler Isoltion (Stndrd) R: RS232C Externl Hrness Type 0: No Hrness 1: Stndrd Hrness (One side cut) 2: Hrness (with USB I/F Cle) (One side cut) 3: Hrness 2 (with Connector nd USB I/F Cle) *. The numers of stcked Notes depends on the Bnknote s condition. Softwre Descriptions Tle 1-3 lists the ivizion Softwre Numer Descriptions. Tle 1-3 ivizion Softwre Numer Specifictions N o Softwre: ivizion-100-ss * * * - * * * - V *.* * N o (A) (B) (C) (D) (A) Softwre Model Nme (B) Denomintion (Country Code) (C) Interfce Protocol Nme (D) Softwre Version Precutions Type 1 Type 2 Type 3 Figure 1-2 Precutionry Symols The Figure 1-2 symols re defined s follows: 1. (Type 1) Do not insert torn, folded, or wet Bnknote into the Unit, s this ction my cuse Bnknote jm inside the unit. 2. (Type 2) Do not expose the Unit to wter. The unit contins severl precision electronic devices which cn e dmged if wter or liquid of ny kind is spryed or spilled into the Unit. 3. (Type 3) Do not instll the Unit into dusty environment. Dust my ffect nd degrde the Sensor s performnce. User Cutions Creful mesures re tken in this product to ensure its qulity, however, the following Cutions should e red nd understood y ll users in order to confirm sfe opertion. INSTALLATION CAUTIONS 1. Do not llow the Unit to endure or operte t high temperture, in high humidity nd/or in dusty environment. 2. Do not instll the Unit into n re where excessive virtion or shock re present. 3. This equipment is not fully wrrnted for outdoor use. Be sure tht the Host Mchine contins enough protection to void wet or dusty conditions when instlling it in oth open-ir nd indoor spces. 4. Avoid exposing the Unit to direct Sunlight nd/or Incndescent Lmp illumintion hving Grdient Angle of 15 Degree or more, nd illumintion index of 3000 Lux or less. 5. Insure tht the Host Mchine is designed for dily opertionl ccess such s mintennce nd/or clering Bnknote jm. 1-2

17 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 MOUNTING, DISMOUNTING & TRANSPORTATION 1. Be sure to turn the Power OFF efore mounting or removing the Unit from its permnent loction. Plugging or unplugging Connector Plugs from their receptcles while the Power is ON my cuse dmge to the Unit. 2. When ressemling disssemled Unit Prt, ensure tht the ech prt is properly replced in its correct originl loction. 3. Be sure to crry the Unit y oth hnds when trnsporting it. Holding the Unit y one hnd my cuse personl injury if the Unit ccidently ecomes disssemled nd drops wy. 4. Be creful not to use excessive outside pressure on the Unit, or suject it to excessive virtion during trnsporttion. PREVENTIVE MAINTENANCE 1. Be sure to turn the Power OFF efore eginning mintennce procedure. The equipment cn produce norml operting signls while in mintennce mode tht my cuse personl injury. 2. If the Vlidtor Section is dirty due to dust, foreign ojects or other such deris dhering to it, Bnknote cceptnce rtes will degrde. Clen the Unit once month to keep its performnce stle. 3. Use soft, lint-free cloth, cotton sw or compressed ir spry to clen dust nd deris from the Bnknote pth. Cution: DO NOT use ny lcohol, solvents, scouring gents or citrus sed cleners tht cn dmge the plstic surfces of the device when clening it. 4. Do not disssemle the Unit incorrectly or redesign it in ny wy. Unuthorized use y indequtely trined personnel, or use outside the originl mnufcturer s intent for opertion voids the wrrnty. 5. When the Unit is exposed to liquid such s wter, wipe nd thermlly dehydrte dry the wet res immeditely. Remining liquid fluids my ffect nd degrde the Sensors nd the Vlidtion Section s performnce. Cution: Mke Interfce Hrness connections to the Host Mchine shorter thn 9.84 Feet (3 Meters) in length. Cut off ll unused portions of the Interfce Hrness wiring to void sttic electricl effects or short circuit possiilities tht could cuse dmge to the Unit. WARNING: This Unit is designed for use with Current limiting Power Source! Design the Host Cinet spce to meet ll locl relted sfety stndrds. BANKNOTE FITNESS REQUIREMENTS The following Bnknote types my not vlidte correctly, or cn cuse Bnknote jm nd/or dmge to the Unit s Trnsport pth. Bnknotes exhiiting the conditions listed elow nd illustrted in Figure 1-3 should e voided: Torn Hving excessive folds Dirty Wet Hving excessive wrinkles Adhering foreign ojects nd/or oil. Figure 1-3 Uncceptle Bnknotes REFERENCE PAPER USE PRECAUTIONS When clirtion using the KS-072 Reference Pper is complete, proceed s follows: Ensure tht the Reference Pper Crrier is kept in n upright position following use (See Figure 1-4 ) or, replce it into its protective Shipping Crton when clirtion is complete (See Figure 1-4 ). KS-072 Reference Pper Shipping Crton Dmged Bnknotes Wrinkled Bnknotes Curled Bnknotes Folded or Prtil Bnknotes Figure 1-4 KS-072 Reference Pper Hndling Precutions KS-072 Reference Pper Do not ly the Reference Pper Crrier down on ny irregulr surfce, otherwise the Reference Pper my ecome wrinkled mking it useless for future clirtion use. ALWAYS return the KS-072 Reference Pper into it protective Shipping Crton following ech use. 1-3

18 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion Primry Fetures The ivizion Series of Bnknote Acceptor contins the following primry fetures: Esily swpple single Vlidtion Hed for inventory nd mintennce efficiently. CIS technology llowing 100% scnning of document detils nd fine line imgery. RFID Intelligent Csh Box with lockle Frme Unit, nd single hndle for one-hnd ction removl without hving to use Button or Lever to relese the Csh Box. Component Nmes Figure 1-5 illustrtes the ivizion Component Nmes nd Loctions. H I O M J K U L B A D E F N S R C G Q T P A. Acceptor Unit B. Front Upper Guide Access Lever (Acceptor Unit) C. Bezel (Option) D. Interfce Connector E. Rer Upper Guide Access Lever (Trnsport Unit) F. Trnsport Unit G. Frme Housing (SS Specifiction) H. DIP Switch Block (Denomintion INHIBIT) I. DIP Switch Block (JCM Custom Privte Line) J. Acceptor Unit Relese Pushutton K. Sttus LED (Four (4) Colors: Red/Yellow/Green & Blue) L. Front Pnel Bezel JPL Connector M. Trnsport Unit Relese Lever N. Power ON LED (Green) O. USB (Mini-B) Softwre Downlod/Clirtion & Mintennce Connector P. Csh Box Q. Stck Volume Indictor Window R. Csh Box Window - confirms the lst stcked Bnknote Denomintion Vlue S. Lock Instlltion Hole (user provided) T. Pusher Lever - mnully moves the Pusher Plte down (Activte lever to confirm the denom- intion vlue through Csh Box Windows R ) U. Frme Housing (LD Version). Figure 1-5 ivizion Component Nmes 1-4

19 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 Specifiction (ivizion SS Version) TECHNICAL SPECIFICATIONS Tle 1-4 ivizion SS Version Technicl Specifiction Acceptnce Rte * : Bnknote Types Accepted: Brcode Coupon : Insertion Direction: Processing Speed: Vlidtion Method: Dignostic Indictors: Escrow: Csh Box Type : Csh Box Cpcity ** : Frud Detection: Interfce : 98% or greter Note: The following Bnknote types re excluded: ) Bnknotes with uncler grphics ) Doule (dul) notes c) Worn, dirty, wet, stined, torn or excessively wrinkled Bnknotes d) Bnknotes hving folded corners or edges e) Bnknotes hving the wrong cut dimensions or printing displcement f) Returned Bnknotes ecuse of incorrect or filed insertion. Long edge: mm ( in.) Short edge: mm ( in.). Stndrd Specifiction ) Red Code interleved: 2 of 5 ) Nrrow Br: 0.5mm-0.6mm ( in.) c) Wide Br: Nrrow Br = 3:1 d) Chrcters: 18 Chrcters e) Print Position: Middle (y dividing Coupon eqully on the left, right, top nd ottom of the Coupon s exct center) f) Print Width: Wider thn 10mm (0.39 in.). Refer to the specific Country s Softwre Informtion Sheet. Approximtely 2 seconds from Bnknote insertion to Vend signl output. Approximtely 3 seconds from Bnknote insertion to completion of the stcking opertion. Opticl Power LED, Sttus LED, Bezel LED (Optionl) 1 Note Secure Csh Box Intelligent Csh Box (ville with RFID Specifiction) Stndrd: 500 Bnknotes Lrge: 900 Bnknotes. Equipped USB Interfce: USB Specifiction Rev.2.0 Seril Interfce: Photo-Coupler Isoltion Seril Interfce: RS232C Communiction Protocol. *. Refer to the specific Country s Softwre Informtion Sheet for ech Country s prticulr Bnknote cceptnce rte.. Refer to the specific Country s Br Code Coupon Specifiction for more detils.. User supplied instlled Locks (including the ttched Plte, Lock nd Key). **.The numer of Notes stcked depends on the Bnknote s condition..the Interfce Hrness connecting to the Host should e less thn 3m. ENVIRONMENTAL SPECIFICATIONS Tle 1-5 ivizion SS Version Environmentl Specifiction Operting Temperture: 5º C to +50º C (41º F to 122º F) Storge Temperture: -20º C to +70º C (-4º F to 158º F) Reltive Operting Humidity: 15% to 85% RH (non-condensed) Reltive Storge Humidity: 15% to 85% RH (non-condensed) Instlltion: Indoors Only [RH%] Hydrotherml Condition Tle Allowle Operting Temperture nd Humidity Rnge 35 C/85% 50 C/40% [ C] 1-5

20 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion ELECTRICAL SPECIFICATIONS Tle 1-6 ivizion SS Version Electricl Specifictions Supply Voltge: Current Consumption: 12V DC (-5%) to 24V DC (+10%) [NOTE: Use Current Source Limiting Power Supply] Stndy: 24V DC = 0.2A, 12V DC = 0.2A Opertion: 24V DC = 1.3A, 12V DC = 2.3A Mximum: 24V DC = 3.2A, 12V DC = 3.0A STRUCTURAL SPECIFICATIONS Tle 1-7 ivizion SS Version Structurl Specifictions Weight Empty: Mounting: Outside Dimensions: Approximtely 4.1kg (9.04 ls) Horizontl (Mximum grdient limittion within 50 degrees; See Figure 1-8 on pge 1-10) Refer to ivizion Bnknote Acceptor SS Version Unit Outside Dimensions on pge 1-9 of this document. 1-6

21 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 Specifiction (ivizion LD Version) TECHNICAL SPECIFICATIONS Tle 1-8 ivizion LD Version Technicl Specifiction Acceptnce Rte * : Bnknote Types Accepted: Brcode Coupon : Insertion Direction: Processing Speed: Vlidtion Method: Dignostic Indictors: Escrow: Frud Detection: Interfce : 98% or greter Note: The following Bnknote types re excluded: ) Bnknotes with uncler grphics ) Doule (dul) notes c) Worn, dirty, wet, stined, torn or excessively wrinkled Bnknotes d) Bnknotes hving folded corners or edges e) Bnknotes hving the wrong cut dimensions or printing displcement f) Returned Bnknotes ecuse of incorrect or filed insertion. Long edge: mm ( in.) Short edge: mm ( in.). Stndrd Specifiction ) Red Code interleved: 2 of 5 ) Nrrow Br: 0.5mm-0.6mm ( in.) c) Wide Br: Nrrow Br = 3:1 d) Chrcters: 18 Chrcters e) Print Position: Middle (y dividing Coupon eqully on the left, right, top nd ottom of the Coupon s exct center) f) Print Width: Wider thn 10mm (0.39 in.). Refer to the specific Country s Softwre Informtion Sheet. Approximtely 2 seconds from Bnknote insertion to Vend signl output. Opticl Power LED, Sttus LED, Bezel LED (Optionl) 1 Note Equipped USB Interfce: USB Specifiction Rev.2.0 Seril Interfce: Photo-Coupler Isoltion Seril Interfce: RS232C Communiction Protocol. *. Refer to the specific Country s Softwre Informtion Sheet for ech Country s prticulr Bnknote cceptnce rte.. Refer to the specific Country s Br Code Coupon Specifiction for more detils.. The Interfce Hrness connecting to the Host should e less thn 3m. ENVIRONMENTAL SPECIFICATIONS Tle 1-9 ivizion LD Version Environmentl Specifiction Operting Temperture: 5º C to +50º C (41º F to 122º F) Storge Temperture: -20º C to +70º C (-4º F to 158º F) Reltive Operting Humidity: 15% to 85% RH (non-condensed) Reltive Storge Humidity: 15% to 85% RH (non-condensed) Instlltion: Indoors Only [RH%] Hydrotherml Condition Tle Allowle Operting Temperture nd Humidity Rnge 35 C/85% 50 C/40% [ C] 1-7

22 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion ELECTRICAL SPECIFICATIONS Tle 1-10 ivizion LD Version Electricl Specifictions Supply Voltge: Current Consumption: 12V DC (-5%) to 24V DC (+10%) [NOTE: Use Current Source Limiting Power Supply] Stndy: 24V DC = 0.2A, 12V DC = 0.2A Opertion: 24V DC = 1.3A, 12V DC = 2.3A Mximum: 24V DC = 3.2A, 12V DC = 3.0A STRUCTURAL SPECIFICATIONS Tle 1-11 ivizion LD Version Structurl Specifictions Weight Empty: Mounting: Outside Dimensions: Approximtely 2.3kg (5.07 ls) Horizontl (Mximum grdient limittion within 50 degrees; See Figure 1-8 on pge 1-10) Refer to ivizion LD Version Unit Outside Dimensions on pge 1-11 of this document. 1-8

23 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 ivizion Entire Unit Outside Dimensions Figure 1-6 illustrtes the ivizion SS Version entire Unit outside dimensions. NOTE: All Dimension re in Millimeters Figure 1-6 ivizion Bnknote Acceptor SS Version Unit Outside Dimensions 1-9

24 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion ivizion SS Version Instlltion/Mintennce Spce Requirements Figure 1-7 illustrtes the ivizion SS Version instlltion nd mintennce nd spce requirements. NOTE: All Dimension re in Millimeters Figure 1-7 ivizion SS Version Unit Instlltion nd Mintennce Spce Requirements Digrm NOTE: If mintennce spce clernce re is unville, the ivizion SS Version Unit will need to e dismounted when mintennce procedures need to e performed. Cution: When instlling the ivizion SS Version Unit into Host Mchine, do not mount it tilted downwrd more thn 50 degrees from Horizontl position (See Figure 1-8). Mximum Angle Figure 1-8 Mximum Grdient Angle = 50 Degrees 1-10

25 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 ivizion LD Specifiction Unit Dimensions Figure 1-9 illustrtes the ivizion LD Unit Outside Dimensions. NOTE: All Dimension re in Millimeters Figure 1-9 ivizion LD Version Unit Outside Dimensions Figure 1-10 illustrtes the ivizion LD Unit with Bezel Outside Dimensions. NOTE: All Dimension re in Millimeters Figure 1-10 ivizion LD Version Unit with Bezel Outside Dimensions 1-11

26 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion Vrious Csh Box Unit Dimensions STANDARD CASH BOX OUTSIDE DIMENSIONS Figure 1-11 illustrtes the ivizion Stndrd Csh Box Outside Dimensions. Figure 1-11 ivizion Stndrd Csh Box Outside Dimensions LARGE CASH BOX OUTSIDE DIMENSIONS Figure 1-12 illustrtes the ivizion Lrge Csh Box Outside Dimensions. NOTE: All Dimension re in Millimeters Figure 1-12 ivizion Lrge Csh Box Outside Dimensions NOTE: All Dimension re in Millimeters 1-12

27 Generl Informtion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 1 Interntionl Complince RoHS Directives or or or UL & c-ul Mrks File No. E142330, Suscrier , Vo.2 CE Mrk CB Scheme NO58326 FCC Directives. Contins Trnsmitter Module FCC ID: VZQNRWA3 MODEL NO.: NRWA3 IC: 8285A-NRWA3 This device complies with Prt 15 of FCC Rules nd RSS-Gen of IC Rules. Opertion is suject to the following two conditions: (1) this device my not cuse interference, nd (2) this device must ccept ny interference, including interference tht my cuse undesired opertion of this device. FCC WARNING Chnges or modifictions not expressly pproved y the prty responsile for complince could void the user s uthority to operte the equipment. FCC NOTICE This equipment hs een tested nd found to comply with the limits for Clss A Digitl Device, pursunt to prt 15 of the FCC Rules. These limits re designed to provide resonle protection ginst hrmful interference when the equipment is operted in commercil environment. This equipment genertes, uses nd cn rdite rdio frequency energy nd, if not instlled nd used in ccordnce with the instructions, my cuse hrmful interference to rdio communictions. Opertion of this equipment in residentil re is likely to cuse hrmful interference in which cse the user will e required to correct the interference t his own expense. IC NOTICE This Clss A Digitl Apprtus complies with Cndin ICES-003. Cet ppreil numerique de l Clsse A est conforme l norme NMB-003 du Cnd. 1-13

28 Section 1 ivizion Series Next-Genertion Bnknote Acceptor Unit Generl Informtion Technicl Contct Informtion AMERICAS & OCEANIA JCM Americn Phone: Fx: Pilot Rod, Ls Vegs, NV E-mil: customerservice@jcmglol.com EUROPE, AFRICA, RUSSIA & MIDDLE EAST JCM Europe GmH Phone: Fx: Muendelheimer Weg 60 D Duesseldorf Germny E-mil: support@jcmglol.eu UK & IRELAND JCM Europe (UK Office) Phone: +44 (0) Fx: +44 (0) Unit B, Third Avenue Denigh West Business Prk Bletchley, Milton Keynes, Buckinghmshire MK1 1DH, UK E-mil: info@jcmglol.eu ASIA JCM Gold (HK) Ltd. Phone: Fx: Unit 1-7, 3/F., Fvor Industril Centre 2-6 Kin Hong Street, Kwi Chung, N.T. Hong Kong E-mil: sipctechsupport@jcmglol.com Jpn Csh Mchine Co, Limited (HQ) Phone: Fx: , Nishiwki, Hirno-ku, Osk JAPAN E-mil: Shohin@jcm-hq.co.jp All of these Wesites re ville vi:

29 2 INSTALLATION ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 This section provides instlltion nd operting instructions for the ivizion Series Next-Genertion Bnknote Acceptor Unit. The informtion within contins the following fetures: Instlltion Process DIP Switch Configurtions Connector Pin Assignments Preventive Mintennce Clering Bnknote Jm Clening Interfce Schemtic Opertionl Flowchrt. INSTALLATION PROCESS Mounting holes re provided in ech Frme Unit to ttch the ivizion to relted Mchine during instlltion. Select nd perform the following steps to instll the ivizion Unit in the relted Mchine s prticulr Frme configurtion: 1. Instll the Interfce Hrness to the Frme Grounding Plte (FG PLT) (See Figure 2-1 ) using the two (2) Floting Collrs (See Figure 2-1 ), the single (1) M2.6x12 W Wsher (See Figure 2-1 c), the single (1) M2.6x10 W Wsher (See Figure 2-1 d) nd the single (1) M2.6 Nylon Nut (See Figure 2-1 e) onto the Frme Assemly. See the Figure 2-1 circled inset to visully see the ssemly completed s required. Figure 2-2 M4 Screws Loctions (Left/Right Side) 3. When n end mounting configurtion is preferred, remove the Csh Box nd olt the rer end of the ivizion Frme into its intended loction using four (4) UNC6-32 Flt Hed Screws from inside the ck end of the Frme s shown in Figure 2-3. e c d Figure 2-1 Interfce Hrness Instlltion Loction 2. When side mounting configurtion is preferred, olt the left nd right side of the ivizion Frme into its intended relted Mchine s loction using six (6) M4 Screws on oth sides of the Frme (3 Screws on ech side s shown in Figure 2-2). Figure 2-3 Flt Hed Screws Loctions (Rer Side) When instlling the ivizion Unit into the Host Mchine, refer to the Figure 1-7 ivizion SS Version Unit Instlltion nd Mintennce Spce Requirements Digrm on pge 1-10 of Section 1 of this Mnul. NOTE: The length of the M4 Screws should e pre-selected so they do not puncture the Plstic Surfce of the ivizion Frme when side mounting configurtion is preferred. 2-1

30 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion NOTE: When instlling the ivizion LD Version Unit into relted Mchine, refer to the ivizion Optionl LD Version Unit Instlltion detiled informtion on pge 2-9. Cle Interconnection Figure 2-4 illustrtes the Cle Hrness interconnection requirements etween the ivizion nd Host Mchine. c ) ivizion Unit ) Interfce Connector (ivizion) c) Hrness d) Host Mchine (e.g., Gme Mchine, Kiosk, etc.) DIP Switch Configurtions This portion provides the denomintion DIP Switch Block Settings for the ivizion Unit. Tle 2-1 Denomintion INHIBIT DIP Switch Settings Vlidtion CPU Bord SW1 Switch No. Switch ON Switch OFF 1 VEND 1 INHIBIT VEND 1 ACCEPT 2 VEND 2 INHIBIT VEND 2 ACCEPT 3 VEND 3 INHIBIT VEND 3 ACCEPT 4 VEND 4 INHIBIT VEND 4 ACCEPT 5 VEND 5 INHIBIT VEND 5 ACCEPT 6 VEND 6 INHIBIT VEND 6 ACCEPT 7 VEND 7 INHIBIT VEND 7 ACCEPT 8 N/A * OFF (Fixed) *. Not Applicle (N/A). Never Switched to ON. d Figure 2-4 Cle Interconnection SW1 Tle 2-2 JCM Privte Line DIP Switch Setting Vlidtion CPU Bord JP1 O JP1 C Mrk Switch No. Non-Mrked (O) Mrked (C) 1 RS-485 Resistnce Terminted RS-485 Resistnce Un-Terminted Tle 2-3 Softwre DIP Switch Settings Controller CPU Bord SW1 Switch No. Switch ON Switch OFF 1 N/A * OFF (Fixed) 2 N/A* OFF (Fixed) 3 N/A* OFF (Fixed) 4 N/A* OFF (Fixed) *. Not Applicle (N/A). Never Switched to ON. Tle 2-4 Seril Communictions DIP Switch Settings Controller CPU Bord JP2 & JP3 JP2 Mrk JP3 R P R P Switch No. Non-Mrked (R) Mrked (P) JP2 RS232C Photo-Coupler Isoltion (Stndrd) JP3 RS232C Photo-Coupler Isoltion (Stndrd) NOTE: When chnging the type of ivizion Seril Communictions, Switches JP2 nd JP3 locted on the Controller CPU Bord must e set to identicl switch positions. PRIMARY LED INDICATIONS The ivizion Unit s pir of Color LEDs illuminte when vrious operting nd error conditions occur. Tle 2-5 LED Error Pttern Indictions No. Condition Power LED * 1 OFF Extinguished (OUT) SW1 LED Indictions Sttus LED Extinguished (OUT) 2 Initilizing Lit Green Blue Flshes 3 Stnd-y Lit Green Extinguished (OUT) 4 Reject Lit Green Green Flshes 5 Bnknote Jm Lit Green Yellow Flshes 6 Anorml Error Lit Green Red Flshes 7 Downloding Lit Green Lit Red Lit Green 8 Performnce Test (Stnd-y) Lit Green Lit Blue *. The Power LED lights Green when Power is supplied to the Unit. 2-2

31 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 Connector Pin Assignments Tle 2-6 lists the ivizion SS/LD Interfce Connector Pin Assignments. Tle 2-6 ivizion SS/LD USB Connection Pin Assignments Bck Side View Pin No. Signl Nme I/O * *. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor.. SG = Signl Ground.. No Connection = SS Version, Connected to ny SG = SU Version. Socket Housing (Trnsport Unit Side): DR1B026JA1 (JCM) Pin Housing (Frme Side): DR1R026PA1 (JCM) Contct Type (Frme Side): D P (JAE) (Poles except 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#26 Contct Type (Frme Side): D P (JAE) (Pole# 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#24 Function 1 24V DC (POWER) POWER +24V DC Power 2 M-RESET IN Bnknote Acceptor Mster Reset Input Signl Line 3 USB- IN/OUT USB Communiction Input/Output Signl Line 4 USB+ IN/OUT USB Communiction Input/Output Signl Line 5 USB GND SG USB Communiction Ground (0V DC) 6 TTL-TXD OUT - 7 TTL-RXD IN - 8 LED POWER OUT LED Drive Line (node) 9 24V DC (POWER) POWER +24V DC Power 10 RS232 GND SG - 11 TXD OUT - 12 I/F +12V DC IN Interfce Power Supply (+12VDC) 13 Vus IN USB Communiction Vus Signl Line (+5V DC) 14 JP+ IN/OUT - 15 TTL-G SG - 16 LED- IN LED Drive Line (cthode) 17 cctlk (P) IN/OUT - 18 POWER GND POWER Power Ground (0V DC) 19 I/F GND SG - 20 RXD IN - 21 DET-GND IN Connect to DET (Pin-22) 22 DET OUT Connect to DET GND (Pin-21) 23 JP- IN/OUT - 24 SU SELECT IN SS/SU Selection 25 cctlk (S) IN/OUT - 26 POWER GND POWER Power Ground (0V DC) 2-3

32 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion CONNECTOR PIN ASSIGNMENTS (CONTINUED 1) Tle 2-7 lists the ivizion SS/LD Photo-Coupler Connector Pin Assignments. Tle 2-7 ivizion SS/LD Photo-Coupler Connector Pin Assignments Bck Side View Pin No. Signl Nme I/O * *. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor.. SG = Signl Ground. Function 1 24V DC (POWER) POWER +24V DC Power 2 M-RESET IN Bnknote Acceptor Mster Reset Input Signl Line 3 USB- IN/OUT - 4 USB+ IN/OUT - 5 USB GND SG - 6 TTL-TXD OUT - 7 TTL-RXD IN - 8 LED POWER OUT LED Drive Line (node) 9 24V DC (POWER) POWER +24V DC Power 10 RS232 GND SG - 11 TXD OUT Serel Communiction Output Signl Line 12 I/F +12V DC IN Interfce Power Supply (+12VDC) 13 Vus IN - 14 JP+ IN/OUT - 15 TTL-G SG - 16 LED- IN LED Drive Line (cthode) 17 cctlk (P) IN/OUT - 18 POWER GND POWER Power Ground (0V DC) 19 I/F GND SG Photo-Coupler Communiction GND 20 RXD IN Seril Communiction Input Signl Line 21 DET-GND IN Connect to DET (Pin-22) 22 DET OUT Connect to DET GND (Pin-21) 23 JP- IN/OUT - 24 SU SELECT IN SS/SU Selection 25 cctlk (S) IN/OUT - 26 POWER GND POWER Power Ground (0V DC). No Connection = SS Version, Connected to ny SG = SU Version. Socket Housing (Trnsport Unit Side): DR1B026JA1 (JCM) Pin Housing (Frme Side): DR1R026PA1 (JCM) Contct Type (Frme Side): D P (JAE) (Poles except 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#26 Contct Type (Frme Side): D P (JAE) (Pole# 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#24 2-4

33 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 CONNECTOR PIN ASSIGNMENTS (CONTINUED 2) Tle 2-8 lists the ivizion SS/LD RS232C Connector Pin Assignments. Tle 2-8 ivizion SS/LD RS232C Connector Pin Assignments Bck Side View Pin No. Signl Nme I/O * *. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor.. SG = Signl Ground. No Connection = SS Version, Connected to ny SG = SU Version. Socket Housing (Trnsport Unit Side): DR1B026JA1 (JCM) Pin Housing (Frme Side): DR1R026PA1 (JCM) Contct Type (Frme Side): D P (JAE) (Poles except 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#26 Contct Type (Frme Side): D P (JAE) (Pole# 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#24 Function 1 24V DC (POWER) POWER +24V DC Power 2 M-RESET IN Bnknote Acceptor Mster Reset Input Signl Line 3 USB- IN/OUT - 4 USB+ IN/OUT - 5 USB GND SG - 6 TTL-TXD OUT - 7 TTL-RXD IN - 8 LED POWER OUT LED Drive Line (node) 9 24V DC (POWER) POWER +24V DC Power 10 RS232C GND SG RS232C Communiction Ground 11 TXD OUT Seril Communiction Output Signl Line 12 I/F + 12V DC IN Interfce Power Supply (+12V DC) 13 Vus IN - 14 JP+ IN/OUT - 15 TTL-G SG - 16 LED- IN LED Drive Line (cthode) 17 cctlk (P) IN/OUT - 18 POWER GND POWER Power Ground (0V DC) 19 I/F GND SG - 20 RXD IN Seril Communiction Input Signl Line 21 DET-GND IN Connect to DET (Pin-22) 22 DET OUT Connect to DET GND (Pin-21) 23 JP- IN/OUT - 24 SU SELECT IN SS/SU Selection 25 cctlk (S) IN/OUT - 26 POWER GND POWER Power Ground (0V DC) 2-5

34 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion CONNECTOR PIN ASSIGNMENTS (CONTINUED 3) Tle 2-9 lists the ivizion SS/LD cctlk Connector Pin Assignments. Tle 2-9 ivizion SS/LD cctlk Connector Pin Assignments Bck Side View Pin No. Signl Nme I/O * *. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor.. SG = Signl Ground.. No Connection = SS Version, Connected to ny SG = SU Version. Socket Housing (Trnsport Unit Side): DR1B026JA1 (JCM) Pin Housing (Frme Side): DR1R026PA1 (JCM) Contct Type (Frme Side): D P (JAE) (Poles except 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#26 Contct Type (Frme Side): D P (JAE) (Pole# 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#24 Function 1 24V DC (POWER) POWER +24V DC Power 2 M-RESET IN Bnknote Acceptor Mster Reset Input Signl Line 3 USB- IN/OUT - 4 USB+ IN/OUT - 5 USB GND SG - 6 TTL-TXD OUT - 7 TTL-RXD IN - 8 LED POWER OUT LED Drive Line (node) 9 24V DC (POWER) POWER +24V DC Power 10 RS232C GND SG - 11 TXD OUT - 12 I/F + 12V DC IN Interfce Power Supply (+12VDC) 13 Vus IN - 14 JP+ IN/OUT - 15 TTL-G SG - 16 LED- IN LED Drive Line (cthode) 17 cctlk (P) IN/OUT cctlk Communiction Power Supply Line 18 POWER GND POWER Power Ground (0V DC) 19 I/F GND SG - 20 RXD IN - 21 DET-GND IN Connect to DET (Pin-22) 22 DET OUT Connect to DET GND (Pin-21) 23 JP- IN/OUT - 24 SU SELECT IN SS/SU Selection 25 cctlk (S) IN/OUT cctlk Communiction Signl Line 26 POWER GND POWER Power Ground (0V DC) 2-6

35 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 CONNECTOR PIN ASSIGNMENTS (CONTINUED 4) Tle 2-10 lists the ivizion SS/LD TTL Connector Pin Assignments. Tle 2-10 ivizion SS/LD TTL Connector Pin Assignments Bck Side View Socket Housing (Trnsport Unit Side): DR1B026JA1 (JCM) Pin Housing (Frme Side): DR1R026PA1 (JCM) Contct Type (Frme Side): D P (JAE) (Poles except 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#26 Contct Type (Frme Side): D P (JAE) (Pole# 1, 9, 18 & 26) Recommended Wire: UL1061 AWG#24 Pin No. Signl Nme I/O * Function 1 24V DC (POWER) POWER +24V DC Power 2 M-RESET IN Bnknote Acceptor Mster Reset Input Signl Line 3 USB- IN/OUT - 4 USB+ IN/OUT - 5 USB GND SG - 6 TTL-TXD OUT TTL Communiction Output Signl Line 7 TTL-RXD IN TTL Communiction Input Signl Line 8 LED POWER OUT LED Drive Line (node) 9 24V DC (POWER) POWER +24V DC Power 10 RS232C GND SG - 11 TXD OUT - 12 I/F + 12V DC IN Interfce Power Supply (+12VDC) 13 Vus IN - 14 JP+ IN/OUT - 15 TTL-G SG - 16 LED- IN LED Drive Line (cthode) 17 cctlk (P) IN/OUT - 18 POWER GND POWER Power Ground (0V DC) 19 I/F GND SG - 20 RXD IN - 21 DET-GND IN Connect to DET (Pin-22) 22 DET OUT Connect to DET GND (Pin-21) 23 JP- IN/OUT - 24 SU SELECT IN SS/SU Selection 25 cctlk (S) IN/OUT - 26 POWER GND POWER Power Ground (0V DC) *. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor.. SG = Signl Ground.. No Connection = SS Version, Connected to ny SG = SU Version. 2-7

36 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion CONNECTOR PIN ASSIGNMENTS (CONTINUED 5) Tle 2-11 lists the ivizion SS/LD Bezel Connector Pin Assignments. Tle 2-11 ivizion SS/LD Bezel JPL (CN7) Connection Pin Assignments CN7 Preventive Mintennce RETRIEVING BANKNOTES To retrieve Csh Box deposited Bnknotes perform the following steps: 1. Relese the Csh Box from the Frme nd pull it forwrd. 2. Unlock the Csh Box with User supplied Key. 3. Open the Csh Box Door nd retrieve deposited Bnknotes s illustrted in Figure 2-5. Front Side View Box Pin Heder (Control CPU Bord Side): A3B-8PA-2DS (71) (HRS) JCM Custom Socket Housing (Bezel Side): A3B-8D-2C (HRS) Contct Type (Bezel Side): A3B-2630SCFC (HRS) Polrizing Pin: A3-GPIN (HRS) * Recommended Wire: UL1007 AWG#24~30 Pin No. Signl Nme I/O Function 1 JP+ IN/OUT Polrizing Pin Key 3 JP- IN/OUT - 4 5V DC OUT 5V DC Power Supply (Mximum 300mA) 5 VIN OUT LED Drive Power Supply 12V DC/24V DC (Mximum 300mA) 6 GND SG - 7 LED POWER OUT LED Power Supply 5V (Mximum 20mA Current Limittion Resistnce) 8 LED 1 IN LED Drive Line (cthode) Mximum Sink Current: 300mA *. Cution: The Emossed Numers locted on the Polrizing Pin Connector, nd on the CN7 Connector Numers indicted in Tle 17 re different. The Polrizing Pin Key should e inserted into Pin Position No.4 of the Polrizing Pin Connector.. I/O (Input/Output) Terminl s viewed from outside the Bnknote Acceptor. Polrizing Pin Connector 2. Remove the jmmed Bnknote. If the jmmed Bnknote is not found in the Acceptor Unit, then 3. Open the Trnsport Unit s Upper Guide y pressing in on the Upper Guide Access Lever (See Figure 2-6 single Blue Arrow) locted in the center of the Upper Guide, nd lift the Trnsport Section up nd open nd remove the jm. Remove Hidden Emossed ID Pin No.4 Open Open Remove Remove Figure 2-5 Retrieving Bnknote CLEARING A BANKNOTE JAM To retrieve jmmed Bnknote jmmed inside the Bnknote Acceptor Hed Prt proceed s follows: 1. Open the Acceptor Unit s Upper Guide y pressing in on the two (2) Upper Guide Access Buttons (See Figure 2-6 Blue Arrows) locted on ech side of the Upper Guide, nd lift the Acceptor top up nd open nd remove the jm. ) Acceptor Unit Upper Guide Access Lever ) Trnsport Unit Upper Guide Access Lever Figure 2-6 Open the Upper Guides 4. If the jmmed Bnknote is not found in the higher Sections, pull the Csh Box out of the Frme (See Figure 2-7 ). Check t the rer side of the Frme nd remove the jmmed Bnknote locted there if ny (See Figure 2-7 ). 5. A jmmed Bnknote my lso e present on top of the Csh Box; remove it if present t this loction (See Figure 2-7 c). 2-8

37 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 Pull Out c Figure 2-7 Retrieving Csh Box Bnknote Jm Clening Procedure To clen the lenses, use lint-free, Micro-Fier Cloth nd mild non-rsive detergent such s liquid dish sop mixed with wter to wipe the dirt from the Lenses. It is importnt to keep the Bnknote Pth, Rollers, nd Belts clen. Use softlint free, Micro-Fier Cloth or Cotton Sw to wipe dirt nd stins from the surfces of the Opticl Sensors, Rollers nd Belts. The Sensor Lenses re trnsprent, nd mde of polymer mteril; Hndle them with cre. When the Unit is exposed to liquid such s wter, wipe nd thermlly dehydrte dry the wet res immeditely. Repet the clening process s needed until the Trnsport Pth is free of contminnts. ivizion Optionl LD Version Unit Instlltion Mounting holes re provided in the LD Frme Unit to ttch the ivizion LD Unit to relted Mchine during instlltion. Perform the following steps to instll the ivizion LD Version Unit into the relted Mchine s Frme configurtion: 1. Instll the Interfce Hrness to the Frme Grounding Plte (FG PLT) (See Figure 2-8 ) using the two (2) Floting Collrs (See Figure & 2 ), the relted single (1) M2.6x12 W Wsher Screws (See Figure 2-8 c & d), nd the single (1) M2.6 Nylon Nut (See Figure 2-8 e) onto the upper Frme Assemly Brcket. See the Figure 2-8 circled inset to visully see the completed ssemly s required. c d 1 2 e Cution: Do not llow ny fluid to remin on internl components, especilly on the Anti-Strings Mechnism nd in the Feed-in Sensor s grooved res. Sensor Clening Procedure 1. Turn the ivizion Unit Power OFF. 2. Clen the Sensors nd lenses in the Acceptor Unit, the Trnsport Unit nd on the Csh Box itself. If necessry, remove ech Unit nd/or open their Upper Guides for clening. See Figure 2-10 nd Tle 2-12 to locte ll clening loctions. Figure 2-8 Interfce Hrness Instlltion Loction 2. Bolt the ottom side of the ivizion LD Frme into its intended Mchine s loction using four (4) M3x6 Screws on oth ottom sides of the Frme (2 Screws on ech side s shown in Figure 2-9). Cution: Do not use Alcohol, thinner or citrus sed products for clening ny Bnknote trnsport Sensors or surfces. The lenses cn ecome clouded y chemicl evportion resdue tht my cuse cceptnce errors. NOTE: When closing the Acceptor or Trnsport Unit s Upper Guides, ensure tht they click firmly into plce when eing closed. Also, when ressemling the ivizion Unit, ensure tht it re-sets correctly into plce when the ressemly is complete. Figure 2-9 M3 Screws Loctions 2-9

38 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion ivizion Sensor Loctions Figure 2-10 illustrtes nd Tle 2-12 lists the ivizion vrious Sensor nd Sensor Lens loctions. n c e f o g p Hidden k h d q j l m Hidden Tle 2-12 ivizion Sensor Clening Loction Types Sym. Sensor Clening Method c d e f g h i j k l m n o p q r Hidden Figure 2-10 ivizion Sensor Clening Loctions Entrnce Sensors Exit Sensors UV Sensor (Upper) Acceptor Unit UV Sensor (Lower) Trnsmissive Sensor CIS Sensor (Upper) CIS Sensor (Lower) Feed-in Sensors Feed-out Sensors Home Position Sensor Trnsport Unit Home Position Sensor Lens Nerly Full Sensor Csh Box Sensor Home Position Sensor Lens Csh Box Csh Box Sensor Lens Nerly Full Sensor Lens Anti-Stringing Mechnism Feed-in Sensor s Com Grooves i r Wipe re clen using lint-free cloth such s Micro-Fier Cloth, or low clen using Compressed Air. 2-10

39 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 Stndrd Interfce Circuit Schemtics Figure 2-11 illustrtes the ivizion USB Circuit Interfce Schemtic Digrms. Controller Side ivizion Side NOTE: The Controller Circuit Schemtic is for reference only nd does not gurntee the ctul Mchine s functionl opertion. Figure 2-11 ivizion USB Circuit Interfce Schemtic Digrm Figure 2-12 illustrtes the ivizion Photo-Coupler Isoltion Circuit Interfce Schemtic Digrms. Controller Side ivizion Side NOTE: The Controller Circuit Schemtic is for reference only nd does not gurntee the ctul Mchine s functionl opertion. Figure 2-12 ivizion Photo-Coupler Circuit Interfce Schemtic Digrm 2-11

40 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion INTERFACE CIRCUIT SCHEMATICS (CONTINUED 1) Figure 2-13 illustrtes the ivizion RS232C Circuit Interfce Schemtic Digrms. Controller Side ivizion Side NOTE: The Controller Circuit Schemtic is for reference only nd does not gurntee the ctul Mchine s functionl opertion. Figure 2-13 ivizion RS232C Circuit Interfce Schemtic Digrm Figure 2-14 illustrtes the ivizion cctlk Circuit Interfce Schemtic Digrms. Controller Side ivizion Side NOTE: The Controller Circuit Schemtic is for reference only nd does not gurntee the ctul Mchine s functionl opertion. Figure 2-14 ivizion cctlk Circuit Interfce Schemtic Digrm 2-12

41 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 INTERFACE CIRCUIT SCHEMATICS (CONTINUED 2) Figure 2-14 illustrtes the ivizion TTL Circuit Interfce Schemtic Digrms. Controller Side ivizion Side NOTE: The Controller Circuit Schemtic is for reference only nd does not gurntee the ctul Mchine s functionl opertion. Figure 2-15 ivizion TTL Circuit Interfce Schemtic Digrm 2-13

42 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion INTERFACE CIRCUIT SCHEMATICS (CONTINUED 3) Figure 2-16 illustrtes the ivizion LED Circuit Interfce Schemtic Digrms. Bezel Side ivizion Side NOTE: Refer to the Cution description stted elow this Figure in order to ensure tht ech Current Limiting Resistnce Vlue is correctly chosen. Figure 2-16 ivizion LED Circuit Interfce Schemtic Digrm Cution: Select the Current Resistnce Limittion Vrile depending on the Voltge t the 5th pin connected to the Mchine s input Power Supply. Mximum Output Supply - 4th pin: 5V 300mA - 5th pin: VIN 300mA - 7th pin: LED Power 20mA Mximum Sink Current - 8th pin: LED1 300mA 2-14

43 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 Opertionl Flowchrt Figure 2-17 depicts typicl ivizion SS/LD Bnknote cceptnce flow process (Initiliztion). ) Initilizing C) Stnd-y return from Figure ) Enter Stnd-y Mode c) Enle Accept? d) LED Disply Extinguished e) LED Disply shows Enle Light f) Is Bnknote inserted? g) Feed Bnknote In h) Bnknote Trnsporting i) Bnknote Dt Smpling j) Stop Trnsporting Bnknote A) To Vlidtion Process (See Figure 2-18). Figure 2-17 ivizion SS/LD Bnknote Acceptor Opertionl Flowchrt (Prt 1 - Initilizing) 2-15

44 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion OPERATIONAL FLOWCHART (CONTINUED 1) Figure 2-18 depicts typicl ivizion SS Bnknote flow process (Vlidtion). A) Begin Vlidting ) Is Vlidtion Result OK? ) Is Bnknote Uncceptle? c) Output the Denomintion Vlue Signl d) Receive Stcking Commnd? e) Reject Bnknote f) Continue Trnsporting Bnknote g) Is Bnknote sent to Stcker? h) Output VEND Signl) i) Retry 3 times? j) Stop Performnce: Output Anorml Signl (*1) k) Bnknote Stcking l) Is Stcker Full? m) Stop Performnce: Issue Output Stcker Full Signl (*2) C) Return To Stnd-y Mode (See Figure 2-17). *1 When Anorml Output Signl condition occurs, remove the Bnknote cusing the mlfunction nd re-pply power to the Unit, or send Reset Commnd to the Bnknote Acceptor. *2 When Stcker Full signl occurs, remove the Bnknotes from the Csh Box nd re-instll it into its fully seted position. The ivizion will the utomticlly re-initilize itself. Figure 2-18 ivizion SS Bnknote Acceptor Opertionl Flowchrt (Prt 2 - Vlidting) 2-16

45 Instlltion ivizion Series Next-Genertion Bnknote Acceptor Unit Section 2 OPERATIONAL FLOWCHART (CONTINUED 2) Figure 2-18 depicts typicl ivizion LD Bnknote flow process (Vlidtion). A) Begin Vlidting ) Is Vlidtion Result OK? ) Is Bnknote Uncceptle? c) Output the Denomintion Vlue Signl d) Receive Stcking Commnd? f) Continue Trnsporting Bnknote g) Is Bnknote sent to Stcker? e) Reject Bnknote h) Output VEND Signl) C) Return To Stnd-y Mode (See Figure 2-17) i) Stop due to Anorml Condition or return to Stnd-y Mode? j) Stop Performnce: Output Anorml Signl (*1) *1 When Anorml Output Signl condition occurs, remove the Bnknote cusing the mlfunction nd re-pply power to the Unit, or send Reset Commnd to the Bnknote Acceptor. Figure 2-19 ivizion LD Bnknote Acceptor Opertionl Flowchrt (Prt 2 - Vlidting) 2-17

46 Section 2 ivizion Series Next-Genertion Bnknote Acceptor Unit Instlltion THIS PAGE INTENTIONALLY LEFT BLANK 2-18

47 3 COMMUNICATIONS ivizion Series Next-Genertion Bnknote Acceptor Unit Section 3 This section ws intentionlly left out due to Non-Disclosure Agreement requirement. If this informtion is required, plese contct the closest office loction listed elow: AMERICAS & OCEANIA JCM Americn Phone: Fx: Pilot Rod, Ls Vegs, NV E-mil: customerservice@jcmglol.com EUROPE, AFRICA, RUSSIA & MIDDLE EAST JCM Europe GmH Phone: Fx: Muendelheimer Weg 60 D Duesseldorf Germny E-mil: support@jcmglol.eu UK & IRELAND JCM Europe (UK Office) Phone: +44 (0) Fx: +44 (0) Unit B, Third Avenue Denigh West Business Prk Bletchley, Milton Keynes, Buckinghmshire MK1 1DH, UK E-mil: info@jcmglol.eu ASIA JCM Gold (HK) Ltd. Phone: Fx: Unit 1-7, 3/F., Fvor Industril Centre 2-6 Kin Hong Street, Kwi Chung, N.T. Hong Kong E-mil: sipctechsupport@jcmglol.com Jpn Csh Mchine Co, Limited (HQ) Phone: Fx: , Nishiwki, Hirno-ku, Osk JAPAN E-mil: Shohin@jcm-hq.co.jp All of these Wesites re ville vi: 3-1

48 ivizion Series Next-Genertion Bnknote Acceptor Unit THIS PAGE INTENTIONALLY LEFT BLANK 3-2

49 ivizion Series Next-Genertion Bnknote Acceptor Unit Section 4 4 DISASSEMBLY/REASSEMBLY This section provides disssemly nd ressemly instructions for the ivizion Next-Genertion Bnknote Acceptor Unit. This section contins the following informtion: Tool Requirements Pusher Unit Timing Belt Removl Home Position Sensor Bord/Home Position Sensor FFC & Interfce Connector Bord Removls RFID Module & RFID Hrness Removls Vlidtion CPU & Controller CPU Bord Removls USB FPC/Power FPC & Interfce FPC Cle Removls Vlidtion Unit Hrness Removl Interrupter Bord Removl Motor Unit Timing Belt Removl Stcker Motor & Trnsport Motor Removls Bezel Hold Chips A/B Removls Sensor Trnsfer Bord/CIS FFC/Trnsmissive Light FFC & Upper UV FPC Sensor Removls Vlidtion Sensor Bord Removl Vlidtion Sensor FPC Crd Removl CIS/Trnsmissive Light/Upper UV Sensor Removls CIS/CIS FPC/Lower UV Sensor & Lower UV FFC Removls Vlidtion Unit Timing Belt Removl. Tool Requirements The following tools will e required to perform ivizion disssemly nd ressemly. #1 & #2 Phillips Screw Driver Set of Jewelers Phillips Screw Drivers #T6 TORX Brnd Torque Wrench Driver #1 & #2 Torque Wrench Drivers Motor Ger Assemly Pressure Br Pliers Tweezers. Pusher Unit Timing Belt Removl To remove the Timing Belt proceed s follows: 1. Remove the Csh Box from the ivizion Unit. 2. Open the Csh Box Door s ottom ccess Door. 3. Remove the two (2) screws (See Figure & 2 ) retining the Pusher Mechnism Unit to the Csh Box. 1 Figure 4-1 Pusher Mechnism Screws Removl 4. While pulling upwrd on the Door Ltch Stoppers (See Figure & 2 ) of the Pusher Mechnism Unit (See Figure 4-2 ), slide it forwrd to remove the Pusher Mechnism Assemly out of the Csh Box. 1 2 Figure 4-2 Pusher Mechnism Removl 5. Remove the four (4) screws (See Figure 4-3 1, 2, 3 & 4 ) retining the Unit Cover in plce (See Figure 4-3 ), nd remove the Unit Cover from the Pusher Mechnism Assemly Figure 4-3 Pusher Mechnism Cover Removl 4 4-1

50 Section 4 ivizion Series Next-Genertion Bnknote Acceptor Unit Disssemly/Ressemly 6. Remove the two (2) screws (See Figure & 2 ) retining the two (2) Flt Lef Springs (See Figure & 2 ). Remove the two (2) Flt Springs, the single (1) Stcker Guide (See Figure 4-4 c), the single (1) Retiner Pin (See Figure 4-4 d), the two (2) Rollers (See Figure 4-4 e 1 & e 2 ) nd the two (2) relted pressure Coil Springs (See Figure 4-4 f & Figure 4-5 elow) from the Pusher Mechnism Assemly. d e 1 c f e 2 g d 2 f e 1 d 1 e 2 c 1 2 e Figure 4-4 Stcker Guide Removl NOTE: When ressemling the Stcker Guide (See Figure 4-5 ), ensure tht ech Coil Spring (See Figure 4-5 ) direction is replced correctly. When reinserting the Retining Pin, put it in plce while lifting the Coil Spring upwrd; then put the Screw Locks ck onto the Screws retining ech Coil Spring in plce. Hidden Figure 4-6 Right Frme Outer R Removl NOTE: When replcing the Frme Outer R Assemly, ensure tht the Plte Nut is correctly re-positioned (See Figure 4-6 g). 9. Remove the single (1) E-ring (See Figure 4-7 ) nd the two (2) Gers (See Figure & 2 ) locted on the left side of the Trnsport Unit. NOTE: Be creful tht the prllel Pins (See Figure 4-7 c) nd their relted Bushings (See Figure 4-7 d 1, d 2 & d 3 ) re not lost when removing them. 10. Remove the three (3) Assemly Mounting Screws (See Figure 4-7 e 1, e 2 & e 3 ) nd remove the Left Frme Outer L Assemly (See Figure 4-7 f) from the Trnsport Unit. e 1 1 c d 1 f 2 d 2 Figure 4-5 Stcker Guide Ressemly 7. Remove the single (1) E-ring (See Figure 4-6 ) nd the single (1) Ger (See Figure 4-6 ) locted on the right side of the Trnsport Unit. NOTE: Be creful tht the prllel Pins (See Figure 4-6 c) nd their relted Bushings (See Figure 4-6 d 1 & d 2 ) re not lost when removing them. 8. Remove the three (3) Assemly Mounting Screws (See Figure 4-6 e 1, e 2 & e 3 ) locted on the right side of the Trnsport Unit, nd remove the Right Frme Outer R Assemly (See Figure 4-6 f) from the Trnsport Unit. e 2 e 3 d 3 Figure 4-7 Left Frme Outer L Removl g 4-2

51 Disssemly/Ressemly ivizion Series Next-Genertion Bnknote Acceptor Unit Section 4 NOTE: When replcing the Frme Outer L Assemly, ensure tht the Plte Nut is correctly re-positioned (See Figure 4-7 g). 11. Remove the two (2) Timing Belts (See Figure & 2 ) from the Trnsport Unit. 4. Use smll Screwdriver to relese the five (5) Click-t Stops of TR Side Cover A (See Figure through 5 ), nd remove TR Side Cover A (See Figure 4-10 ) from the Trnsport Assemly Figure 4-8 Timing Belt Removl NOTE: The Timing Belts should e replced s illustrted in Figure 4-8 when ressemling the Unit. Be creful tht the Pulleys nd/or Rollers do not ccidentlly fll off during ressemly. Home Position Sensor Bord/Home Position Sensor, FFC & Interfce Connector Bord Removls To remove the Home Position Sensor Bord, the Home Position Sensor FFC nd the Interfce Connector Bord proceed s follows: 1. Remove the Trnsport Unit from the ivizion Unit. 2. Remove the Vlidtion Section from the Trnsport Unit. 3. Remove the two (2) TR Cover mounting Screws (See Figure & 2 ) from the ottom of the Trnsport Unit, nd remove the Trnsport (TR) Bottom Cover (See Figure 4-9 ) off the Trnsport Unit. Figure 4-10 TR Side Cover A Removl NOTE: When the three (3) lower Click-t stops re difficult to remove from the top, relese them from ottom-side insted. 5. Remove the two (2) mounting Screws (See Figure & 2 ) retining the Home Position Sensor Bord in plce (See Figure 4-11 ). 6. Remove the Home Position Sensor Bord nd the Home Position Sensor FFC Assemly (See Figure 4-11 c) from the Trnsport Unit. 7. Remove the three (3) mounting Screws (See Figure 4-11 d 1, d 2 & d 3 ) retining the Interfce Connector Bord in plce (See Figure 4-11 f), nd then remove the three (3) Flt Rion Cles from the Interfce Connector Bord (See Figure 4-11 e 1, e 2 & e 3 ). d 1 d 2 f 1 d 3 c e2 e 1 e Figure 4-11 Home Position Sensor Bord, Home Position Sensor FFC Assemly nd Interfce Connector Bord Removls Figure 4-9 TR Bottom Cover Removl 4-3

52 Section 4 ivizion Series Next-Genertion Bnknote Acceptor Unit Disssemly/Ressemly RFID Module & Hrness Removls To remove the RFID Module nd RFID Hrness proceed s follows: 1. Remove the two (2) mounting Screws (See Figure & 2 ) retining the RFID Module to the ck side of the Trnsport Unit (See Figure 4-12 ). 2. Remove the RFID Module nd the RFID Hrness (See Figure 4-12 c) from the Trnsport Unit. 2. Remove the single (1) mounting Screw (See Figure 4-14 ) nd remove the Optionl Extension Memory Bord if instlled (See Figure 4-14 ) from the ssemled Extension Memory Bord. c 1 2 Figure 4-14 Extension Memory Bord Removl 3. Crefully spred oth sides of the PCB Support prt (See Figure & 2 ) nd slide the Vlidtion CPU Bord (See Figure 4-15 d) nd the Controller CPU Bord (See Figure 4-15 c) off of the CPU Bord Module. 4. Remove two (2) mounting Screws (See Figure & 2 ), nd seprte the Vlidtion CPU Bord nd the Controller CPU Bord from one nother if they exist seprtely. Figure 4-12 RFID Module & Hrness Removl Vlidtion CPU & Controller CPU Bord Removls To remove the Vlidtion CPU Bord nd the Controller CPU Bord from the CPU Bord Module, proceed s follows: 1. Remove the four (4) mounting Screws tht re (See Figure through 4 ) retining the CPU Bord Module (See Figure 4-13 d) to the Trnsport Unit, nd unplug the two (2) Signl Connectors (See Figure & 2 ) with the three (3) Flt Rion Cles (See Figure 4-13 c 1, c 2 & 3 ) locted on the CPU Bord Module nd remove the CPU Bord Module from the Trnsport Unit c1 c 2 c 3 d Figure 4-13 CPU Bord Module Removl Figure 4-15 Vlidtion CPU Bord nd Control CPU Bord Removl USB FPC, Power FPC & Interfce FPC Cle Removls To remove the USB FPC, the Power FPC nd the Interfce FPC proceed s follows: 1. Remove the two (2) mounting Screws (See Figure & 2 ) retining the Motor Unit to the Trnsport Assemly, nd remove the Motor Module (See Figure 4-16 ) from the Trnsport Unit. 2. Remove the USB FPC (See Figure 4-17 ), the Power FPC (See Figure 4-17 ) nd the Interfce FPC (See Figure 4-17 c) from the Trnsport Unit. NOTE: Crefully oserve the Up nd Down Fold Line indictions shown y the two (2) Cyn Arrows in Figure 4-17, nd DO NOT reend them in n opposite direction! c d 4-4

53 Disssemly/Ressemly ivizion Series Next-Genertion Bnknote Acceptor Unit Section 4 NOTE: When instlling new FPCs, fold-up long the Solid Lines nd fold-down long the Dshed Lines efore setting them in plce. Once n FPC is folded, DO NOT refold it ck gin or in the opposite direction once folded! d 1 1 d 2 c 1 c Figure 4-16 Motor Module Removl Figure 4-18 Vlidtion Unit Hrness Removl Interrupter Bord Removl To remove the Interrupter Bord proceed s follows: 1. Remove the two (2) mounting Screws (See Figure & 2 ) retining the Interrupter Bord to the Assemly (See Figure 4-19 ), nd crefully unplug the three (3) Signl Connectors (See Figure 4-19 c 1, c 2 & c 3 ) from the Bord. 2. Crefully pull the Interrupter Bord off of the Motor Module Assemly. c Dshed Line for Fold Up Solid Line for Fold Down c 1 c c 3 Figure 4-17 USB FPC, Power FPC & Interfce FPC Cle Removl Vlidtion Unit Hrness Removl To remove the Vlidtion Unit Hrness proceed s follows: 1. Remove the two (2) mounting Screws (See Figure & 2 ) retining the Vlidtion Unit Hrness in plce (See Figure 4-18 ). 2. Remove the Vlidtion Unit Hrness from the Trnsport Unit. NOTE: Ensure tht when the Collrs (See Figure 4-18 c 1 & c 2 ) nd/or Wshers re removed (See Figure 4-18 d 1 & d 2 ) tht they re not ccidentlly lost once they re removed. Figure 4-19 Interrupter Bord Removl Motor Unit Timing Belt Removl To remove the Timing Belt, proceed s follows: 1. Remove the two (2) mounting Screws (See Figure & 2 ) nd remove Drive Mod FR A (See Figure 4-20 ) from the Motor Module Assemly. d Figure 4-20 Timing Belt Removl c

54 Section 4 ivizion Series Next-Genertion Bnknote Acceptor Unit Disssemly/Ressemly NOTE: When re-ssemling Drive Mod FR A, ensure tht it mtes directly with the D Plne of the Drive Shft. 2. Remove the Belt Reel (See Figure 4-20 c) nd the Timing Belt (See Figure 4-20 d) from the Motor Module Assemly. NOTE: Follow the sme procedure to remove the opposite side Timing Belt. NOTE: The 1 Mounting Screws should e reinstlled using #1 (2.5kgfxcm) Torque Wrench Driver. NOTE: When ressemling the TR-ST Motor Ger, Motor Ger Assemly Pressure Br will e required. Bezel Retiner Clips A & B Removl To remove Bezel Retiner Clips A nd Bezel Retiner Clips B proceed s follows: 1. Remove the two (2) lminted, M2.6x6 Phillips Self Tightening Screws (See Figure nd 2 ) from the Bezel, nd then remove Bezel Retiner Clip A from the left side of the Assemly (See Figure 4-23 ). 2. Remove the two (2) lminted M2.6x6 Phillips Self Tightening Screws (See Figure nd 4 ) from the Bezel, nd then remove Bezel Retiner Clip B from the right side of the Assemly (See Figure 4-23 c). 2 Figure 4-21 Timing Belt Ressemly Pth NOTE: The Timing Belts should e replced s illustrted y the Blue pth in Figure 4-21 when the Unit is eing ressemled. Stcker Motor & Trnsport Motor Removls To remove the Stcker Motor nd the Trnsport Motor proceed s follows: 1. Remove the Ger TR-ST Motor (See Figure 4-22 ) nd the two (2) mounting Screws (See Figure & 2 ) retining the Motor Module in plce. 2. Remove the Stcker Motor (See Figure 4-22 c) from the Motor Module Assemly. NOTE: Follow the sme procedure to remove the opposite side Timing Belt. 1 2 Figure 4-22 Stcker & Trnsport Motor Removl c 1 Figure 4-23 Bezel Retiner Chips A&B Removl NOTE: Use T6 TORX Torque Wrench Driver when rettching Bezel Retiner Clips A nd B onto the Trnsport Unit. Sensor Trnsfer Bord/CIS FFC/ Trnsmissive Light FFC & Upper UV FPC Sensor Removls To remove the Sensor Trnsfer Bord, the CIS FFC Sensor, the Trnsmissive Light FFC Sensor nd the Upper UV FPC Sensor proceed s follows: 1. Open the Vlidtion Section nd relese the six (6) Upper Cover Click-t Stops (See Figure through 6 ) y using smll Screwdriver. 2. Remove the Upper Cover (See Figure 4-24 ) from the Upper Guide. 3. Remove the two (2) mounting Screws (See Figure & 2 ) retining the Sensor Trnsfer Bord Assemly to the Trnsport. 4. Remove the CIS FFC (See Figure 4-25 ), the Trnsmissive Light FFC (See Figure 4-25 c), nd the Upper UV FPC (See Figure 4-25 d) from the Vlidtion Hed. 5. Unplug the two (2) Flt Rion Cles (See Figure 4-25 e 1 & e 2 ) nd then remove the Sensor Trnsfer Bord Assemly (See Figure 4-25 f) off of the Vlidtion Hed; then 6. Remove the CIS FFC, the Trnsmissive Light FFC nd the Upper FPC from the Vlidtion Unit. c

55 Disssemly/Ressemly ivizion Series Next-Genertion Bnknote Acceptor Unit Section Remove the two (2) screws (See Figure 4-27 c 1 & c 2 ) retining the Vlidtion Sensor Assemly Bord. 4. Unplug the two (2) FPC Cles (See Figure 4-27 d 1 & d 2 ) nd the two (2) FFC Cles (See Figure 4-27 e 1 & e 2 ) from the Vlidtion Sensor Assemly Bord. 5. Tke the Vlidtion Sensor Bord Assemly (See Figure 4-27 f) off the Vlidtion Unit. Figure 4-24 Upper Cover Removl 1 2 e 1 e 2 c d f Figure 4-26 ivizion Hed Cover A Removl 1 2 Figure 4-25 Sensor Trnsfer Bord Assemly, CIS FFC, Trnsmissive Light & Upper UV FPC Cle Removl Vlidtion Sensor Bord Assemly Removl To remove the Vlidtion Sensor Bord Assemly, proceed s following: 1. Remove the four (4) Cover Mounting Screws (See Figure through 4 ) locted on the se side of the Vlidtion Unit, nd remove the ivizion Hed Cover A (See Figure 4-26 ) off the Vlidtion Assemly. 2. Remove the two (2) mounting Screws (See Figure & 2 ) nd tke Grounding Plte A (See Figure 4-27 ) off the Vlidtion Unit. d 1 e 1 e 2 d2 c 1 c2 Figure 4-27 Vlidtion Sensor Bord Assemly Removl 4-7

56 Section 4 ivizion Series Next-Genertion Bnknote Acceptor Unit Disssemly/Ressemly Vlidtion Sensor FPC Cle Removls To remove the Vlidtion Sensor FPC Cles, proceed s follows: 1. Remove the two (2) Vlidtion Sensor FPC Cles (See Figure & 2 ) from the Vlidtion Unit. 1 Dshed Line for Fold Up Solid Line for Fold Down NOTE: When ressemling the Unit, ensure tht the right nd left side Pins re correctly repositioned when reset into plce. 2. Crefully spred oth side of ivizion Hed FR A Frme prt (See Figure 4-30 c 1 & c 2 ), nd lift the Upper Vlidtion Section (See Figure 4-30 d) up nd out of the Vlidtion Unit. 1 d 2 c Figure 4-28 Vlidtion Sensor FPC Removl NOTE: Crefully oserve the Up nd Down Fold Line indictions shown y the two (2) Cyn Arrows in Figure 4-28, nd DONOT reend them in n opposite direction! NOTE: When instlling new FPCs, fold-up long the Solid Lines nd fold-down long the Dshed Lines efore setting them in plce. Once n FPC is folded, DONOT refold it ck gin or in the opposite direction once folded! NOTE: When the Unit is ressemled, the FPCs should e reinstlled s illustrted y the Blue pths shown in Figure c 2 Figure 4-30 Upper Vlidtion Prt Removl 3. Remove the six (6) mounting Screws (See Figure through 6 ) retining the upper ivizion BG 85B Hed Assemly (See Figure 4-31 ) to the lower Vlidtion Unit Figure 4-29 Vlidtion Sensor FPC Ressemly CIS/Trnsmissive Light & Upper UV Sensor Removls To remove the CIS, the Trnsmissive Light nd the Upper UV Sensors proceed s follows: 1. Push out the two (2) Alignment Pins (See Figure & 2 ) retining the two (2) Limit Stops (See Figure & 2 ) inside the Unit, nd individully remove the two (2) Stops from the Vlidtion Unit. Figure 4-31 ivizion Hed BG85B Removl 4-8

57 Disssemly/Ressemly ivizion Series Next-Genertion Bnknote Acceptor Unit Section 4 4. Remove the four (4) CIS Sensor Mounting Screws (See Figure through 4 ) nd remove the CIS Sensor (See Figure 4-32 ) from the Upper Vlidtion Section. NOTE: When ressemling the Unit, ensure tht the UV Sensors re correctly re- positioned when set in plce (See Ressemly Cutions on pge 4-10 of this Section). NOTE: If foreign ojects re oserved dhering to the Sensor s surfce, low it clen y using Compressing Air spry. 5. Remove the two (2) mounting Screws (See Figure 4-32 c 1 & c 2 ) retining the Trnsmissive Light Sensor in plce (See Figure 4-32 d), nd remove it from the Upper Vlidtion Section. 6. Remove the two (2) mounting Screws (See Figure 4-32 e 1 & e 2 ) retining the Upper UV Sensor in plce (See Figure 4-32 f), nd drop it down nd off the Upper Vlidtion Section. c e 2 e c 4 c 2 Figure 4-33 ivizion BG 85A HEAD Removl 3. Remove two (2) mounting screws (See Figure & 2 ) retining the Lower Vlidtion Section in plce (See Figure 4-34 ) nd remove it up nd off the Vlidtion Unit. 2 1 d f Figure 4-32 CIS, Trnsmissive Light & Upper UV Sensor Removl CIS/CIS FPC/Lower UV Sensor & Lower UV FFC Removl To remove the CIS, the CIS FPC, the Lower UV Sensor nd the Lower UV FFC proceed s follows: 1. Remove three (3) BG 85A Hed Mounting Screws (See Figure , 2 & 3 ) nd relese the four (4) Clip-t Stops (See Figure through 4 ) on the ivizion BG 85A Hed. 2. Remove the ivizion BG 85A Hed (See Figure 4-33 c) up nd off of the Vlidtion Unit. Figure 4-34 Lower Vlidtion Prt Removl 4-9

58 Section 4 ivizion Series Next-Genertion Bnknote Acceptor Unit Disssemly/Ressemly 4. Remove the four (4) CIS Sensor Mounting Screws (See Figure through 4 ), nd remove the CIS Sensor (See Figure 4-35 ) nd the CIS FPC Cle (See Figure 4-35 c) off of the Lower Vlidtion Section. NOTE: If foreign ojects re oserved dhering to the CIS surfce, low it clen y using Compressed Air spry. 5. Remove two (2) mounting screws (See Figure 4-35 d 1 & d 2 ), retining the Lower UV Sensor in plce (See Figure 4-35 e) nd remove it nd the Lower UV FFC Cle (See Figure 4-35 f) from the Lower Vlidtion Section. c Figure 4-36 Timing Belt Removl NOTE: The Timing Belt should e reinstlled s illustrted y the Blue pth shown in Figure 4-37 when the Unit is eing ressemled. e f c Figure 4-37 Timing Belt Replcement Ressemly Cutions When ressemling the Upper/Lower UV Sensors, mke sure tht oth of the Sensor positions nd directions re correctly plced. Mtch the Connector s position s illustrted in Figure [Upper] [Lower] 2 1 d 1 d 2 3 Figure 4-35 CIS, CIS FPC, Lower UV Sensor & Lower UV FFC Removl NOTE: When ressemling the Unit, ensure tht the UV Sensors re correctly re-positioned nd set in plce s illustrted in Figure 4-38 on this pge. Vlidtion Unit Timing Belt Removl To remove Timing Belt proceed s follows: 1. Remove the three (3) Side Plte Cover Mounting Screws (See Figure , 2 & 3 ) locted on right side of the Lower Vlidtion Section. 2. Remove the Cover (See Figure 4-36 ) from the Lower Vlidtion Section. 3. Remove Timing Belt (See Figure 4-36 c) from the Lower Vlidtion Section. NOTE: Follow the sme procedure to remove the opposite side Timing Belt. Figure 4-38 Upper/Lower UV Sensors Loction NOTE: Ensure tht ll Sensors nd the ivizion BG 85B Hed surfces re solutely clen efore ressemling the ivizion Unit. Also ensure tht ll Finger Prints, smudges, dirt or film tht exists on ny surfces in the Trnsport pth re removed. Disssemly nd Ressemly of the ivizion Unit is now complete. 4-10

59 ivizion Series Next-Genertion Bnknote Acceptor Unit Section 5 5 WIRING DIAGRAMS This chpter provides the ivizion Next-Gen- ertion Bnknote Acceptor Unit Wiring Digrms for the following items: ivizion System Wiring Digrm System Wiring Digrm. Figure 5-1 ivizion System Wiring Digrm 5-1

60 Section 5 ivizion Series Next-Genertion Bnknote Acceptor Unit Wiring Digrms THIS PAGE INTENTIONALLY LEFT BLANK 5-2

61 ivizion Series Next-Genertion Bnknote Acceptor Unit Section 6 6 CALIBRATION AND TESTING This section provides Clirtion nd Performnce Testing instructions for the ivizion Next-Genertion Bnknote Acceptor Unit nd contins the following informtion: Downlod nd Instlltion Workench Tool Requirements Appliction Softwre Instlltion Procedure Driver Instlltion Procedure JCM Tool Suite Stndrd Edition Mode Softwre Downlod Tool Requirement Softwre Downloding Procedure When to Clirte Reference Pper Plcement Clirtion Tool Requirements Clirtion Preprtion Clirtion Procedures Performnce Tests with PC Performnce Test Tool Requirement Performnce Test Preprtion Performnce Tests with the Externl Switch Utility Function. Downlod nd Instlltion Workench Tool Requirements Figure 6-1 illustrtes nd list identifies the tools nd equipment interconnects necessry to downlod nd instll the ivizion Device. e, f c d d 1 d 2 ) ivizion Device ) Power Supply c) PC (OS: Windows XP) d) USB Cle d 1 ) USB A Terminl Plug d 2 ) USB Mini B Terminl Plug e) ivizion USB Driver (usivizion.inf) f) Appliction Softwre* (JCM Tool Suite Stndrd Edition). *. Contining USB Downloder, Sensor Clirtion, Performnce Test progrms nd Utility Function. Figure 6-1 Tool nd Hrness Connections Appliction Softwre Instlltion Perform the following steps to instll the JCM Tool Suite Stndrd Edition Appliction Softwre (Refer to Figure 6-1 nd Figure 6-2 for the necessry Tool nd Hrness Connections nd USB Cle Type Requirements respectively). 1. Copy the JCMToolSuiteStndrdEdition.zip Appliction Softwre nd extrct on the Desktop. 2. Open the Third Lyer of the extrcted Folder nd Doule-click on Setup.exe (See Figure 6-3 ). Figure 6-3 Setup.exe File Loction The JCM Tool Suite Stndrd Edition - Instll Shield Wizrd Screen shown in Figure 6-4 will pper. 3. Mouse-click on Next> Screen Button (Figure 6-4 ). ) PC Side (USB A Terminl) ) ivizion Side (USB Mini-B Terminl) Figure 6-2 USB Cle Type Requirement Figure 6-4 Instll Shield Wizrd Screen 4. When the Custom Informtion Screen shown in Figure 6-5 ppers, Mouse-click on the Rdio Screen Button locted next to the Anyone who use this computer (See Figure 6-5 ) nd Mouse-click on Next> Screen Button. 6-1

62 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing Figure 6-5 Customer Informtion Screen NOTE: The OEM in Lst Nme: nd Orgniztion: fields re defult settings. The ctul Lst Nme nd Orgniztion Nme is ville for Customer s use. 5. Mouse-click on Next> Screen Button (See Figure 6-6 ) when the Destintion Folder Screen shown in Figure 6-6 ppers. Figure 6-6 Destintion Folder Screen 6. Check the Current Settings: re (See Figure 6-7 ) nd then Mouse-click on the Instll Screen Button (See Figure 6-7 ) to strt the instlltion. Figure 6-8 Instlltion Completion Screen 8. Mouse-click on the Finish Screen Button to end the instlltion process. This completes the JCM Tool Suite Stndrd Edition instlltion procedure. Driver Instlltion Procedure Perform the following steps to instll the vrious ivizion Softwre Drivers (Refer to Figure 6-1 for the Tool Requirements nd Hrness Connector loctions). Before downloding the ivizion USB Driver the usivizion.inf ppliction must e instlled in designted Folder on the PC first. llows: 1. Connect the USB Cle to the ivizion Unit. 2. Supply power to the ivizion Unit. 3. The Hrdwre Updte Wizrd Screen shown in Figure 6-10 will pper. Mouse-click on the Rdio Screen Button locted eside No, not this time (See Figure 6-9 ) nd then Mouse-click on the Next> Screen Button (See Figure 6-9 ). Figure 6-7 Current Settings Confirmtion 7. Once instlltion is complete, the InstllShield Wizrd Completed Screen shown in Figure 6-8 will pper. Figure 6-9 Hrdwre Updte Wizrd Screen 1 4. When the Screen shown in Figure 6-10 ppers, Mouse-click on the Rdio Screen Button locted eside Instll the softwre utomticlly (Recommended) line (See Figure 6-10 ), nd then Mouse-click on the Next> Screen Button (See Figure 6-10 ). 6-2

63 Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 Figure 6-10 Hrdwre Updte Wizrd Screen 2 5. The USB Driver locting process will egin. If the Hrdwre Instlltion Wrning shown in Figure 6-11 ppers, Mouse-click on the Continue Anywy Screen Button (See Figure 6-11 ). JCM Tool Suite Stndrd Edition Mode The following two (2) mode feture types exist in the JCM Tool Suite Stndrd Edition pckge: Norml Mode Test Mode. Norml Mode is mode designed to provide the ivizion Operting Softwre to e downloded. The Service Mode contins three (3) ville choices in its Pull-down Menu shown in Figure 6-13 s follows: Downlod (for downloding softwre) Sttistics (for oserving log dt) Utility (for setting ICB nd CIS Imge functions). Figure 6-11 Hrdwre Updte Wizrd Screen 3 6. The (usivizion.inf) USB Driver instlltion process will now egin. 7. When Softwre instlltion is complete, the Completing the Found New Hrdwre Wizrd Screen will pper s shown in Figure Figure 6-12 Hrdwre Updte Wizrd Screen 4 8. Mouse-click on the Finish Screen Button to close the Completing Screen (See Figure 6-12 ). 9. Turn the ivizion power switch OFF. This complete the ivizion USB Driver Softwre instlltion procedure. Test Mode is mode designed to perform ivizion Clirtion nd Performnce Testing. The Service Mode contins five (5) ville choices in its Pull-down Menu shown Figure 6-14 s follows: Downlod (for downloding softwre) Sttistics (for oserving log dt) Sensor Adjustment (for clirtion) Performnce Test (for performnce testing) Utility (for setting ICB nd CIS Imge functions). Softwre Downlod Tool Requirements The tools listed in Figure 6-15 re required to instll the ivizion Operting Softwre. e, f c Figure 6-13 Norml Mode Selection Figure 6-14 Test Mode Selection d d 1 d 2 ) ivizion Device ) Power Supply c) PC (OS: Windows XP) (ivizion USB Driver instlled) d) USB Cle d 1 ) USB A Terminl Plug d 2 ) USB Mini B Terminl Plug e) Appliction Softwre* (JCM Tool Suite Stndrd Edition) f) ivizion Softwre Progrm. *. Contining USB Downloder, Sensor Clirtion, Performnce Test progrms nd Utility Function. Figure 6-15 Required Softwre Downlod Tools 6-3

64 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing Softwre Downlod Procedures The following two (2) types of downlod procedures exist, depending on the ivizion operting conditions: The ivizion contins the ivizion Softwre Progrm lredy instlled (Upgrding) The ivizion is new nd does not hve the ivizion Softwre Progrm instlled (e.g., New CPU Bord). DOWNLOAD THE UPGRADE PROGRAM To downlod the ltest ivizion Softwre Progrm into new ivizion, proceed s follows: 1. Turn the ivizion Power Switch to OFF. 2. Set ll of the 8-Position DIP Switches to OFF (See Figure 6-16). Figure 6-18 JCM Tool Suite Stndrd Edition Screen Pull-Down Menu Figure 6-16 DIP Switches All OFF 3. Connect the USB Port locted on the front side of the ivizion Unit to the PC using USB A to mini-b Communictions Cle. 4. Turn the ivizion Power Switch to ON. 5. Lunch the JCM Tool Suite Stndrd Edition Appliction. The Screen shown in Figure 6-17 will pper when the ppliction ecomes ctivte. Figure 6-19 Browse Screen Button Loction 8. Select the Current ivizion Softwre Progrm Version (e.g., the ivizion 100(USA)ID003 V13901 exmple shown in Figure 6-20) from the Downlod File Screen tht ppers. 9. Mouse-click on the Open Screen Button (See Figure 6-20 ). Figure 6-17 JCM Tool Suite Stndrd Edition Scree 6. Mouse-click on, nd hold-down the Service Mode Pull Down Menu nd re-select Downlod from within the Pull-Down Menu Selections. When re-selected it will highlight the selected Field Blue (See Figure 6-18), the Sttus LED will flsh t Green Color rte. Once ctivted, Downlod will occur, the JCM Downloder Suite Edition Version X.XX will utomticlly egin functioning, nd the Screen shown in Figure 6-19 will pper. 7. Mouse-click on the Browse Screen Button (See Figure 6-19 ). Figure 6-20 ivizion Softwre Progrm Selection 10. When the JCM Downloder Suite Screen reppers, Mouse-click on the center Downlod Screen Button (See Figure 6-21 ) to egin the Softwre downlod into the ivizion Unit. The Downlod Screen will disply Progress Brogrph during the downlod opertion (See Figure 6-21 ), nd Blue Text Line elow the Downlod Screen Button will disply the downlod Percentge s Downloding : XX% (See Figure 6-21 c). The Sttus LED will lterntely light Green nd Red during this opertion. 6-4

65 Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 c Figure 6-21 Downlod Progress Screen When the downlod is complete, the Downlod Success. Reset Done. Witing for USB Cle Disconnection. Blue Text Line will pper (See Figure 6-22 ). 12. Confirm tht the Host s Checksum nd the Device Checksum s identiclly mtch ech other (See Figure 6-22 ). Figure 6-24 JCM Tool Suite Stndrd Edition Screen 2 6. Mouse-click on, nd hold-down the Service Mode Pull-down Menu selection nd Slidedown the Menu to re-select Downlod from within the Menu Selections. When selected it with Highlight the selected Field Are Blue (See Figure 6-25), nd the Sttus LED will flsh t Green Color rte. = Figure 6-22 Downlod Completed Screen 1 DOWNLOADING THE PROGRAM FIRST TIME When the ivizion Softwre Progrm is not preinstlled (e.g., when chnging the CPU Bord), the downlod procedure for n empty Unit is slightly different from the Downlod nd Upgrde Progrm procedures tht lter follow. To downlod the ivizion Softwre Progrm into n empty ivizion for the first time, proceed s follows: 1. Turn the ivizion Power Switch to OFF. 2. Set 8-Position DIP Switch #6, #7 nd #8 to ON (See Figure 6-23). Figure 6-25 JCM Tool Suite Stndrd Edition Screen Pull-Down Menu 2 Once Downlod is ctivted, the JCM Downloder Suite Edition Version X.XX will utomticlly egin functioning, nd the Screen shown in Figure 6-26 will pper. 7. Mouse-click on the Browse Screen Button (Figure 6-26 ). Figure 6-23 DIP Switches 6, 7, & 8 ON 3. Connect the USB Port locted on the front side of the ivizion Unit to the PC using the A / mini-b USB Communictions Cle. 4. Turn the ivizion Power Switch to ON. The Sttus LED will flsh t Green Color rte. 5. Lunch the JCM Tool Suite Stndrd Edition Appliction. The Screen shown in Figure 6-24 will pper when the ppliction is ctivte. Figure 6-26 Browse Screen Button Loction 8. Select the current ivizion Softwre Progrm version (e.g., ivizion100(usa)id003v13901 in the Figure 6-27 exmple) from the Downlod File Screen tht ppers, then Mouse-click on the Open Screen Button (See Figure 6-27 ). 6-5

66 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing Figure 6-27 ivizion Softwre Progrm Selection 9. When the JCM Downloder Suite Screen reppers, Mouse-click on the center Downlod Screen Button (See Figure 6-28 ) to egin the Softwre downlod into the ivizion Unit. The Downlod Screen will disply Progress Brogrph during the downlod opertion (See Figure 6-28 ), nd Blue Text Line elow the Downlod Screen Button will disply the downlod Percentge s Downloding : XX% (See Figure 6-28 c). The Sttus LED will lterntely light Green nd Red. Figure 6-28 Downlod Progress Screen When the downlod is complete, the Downlod Success. Reset Done. Witing for USB Cle Disconnection. Blue Text Line will pper (See Figure 6-29 ). 11. Confirm tht the Host s Checksum nd the Device Checksums identiclly mtch ech other (See Figure 6-29 ). = c Clirtion This section provides instructions for performing clirtion of the Acceptor Unit Sensors nd the Trnsport Unit Sensors within the ivizion Device. When to Clirte Clirtion should e performed when one of the following four (4) conditions occur: 1. When removing one of the Circuit Bords. 2. When replcing one of the Circuit Bords. 3. When dirt dheres to the Sensors (See Sensor Clening Procedure on pge 2-9 of this Section). 4. When the Bnknote Acceptnce Rte ecomes drsticlly degrded. CALIBRATION ORDER Tle 6-1 lists the Clirtion Order relted to ech ivizion Sensor s Screen indiction. Tle 6-1 ivizion Sensor Clirtion Order Step Screen Indiction Relted Sensor Clirtion #1 Clirtion #2 Clirtion #3 Clirtion #4 Box RUNNING Nerly Full RUNNING Feed-Out RUNNING Home Position RUNNING Feed-In RUNNING Entrnce RUNNING Exit RUNNING UV RUNNING UV RUNNING CIS RUNNING Csh Box Sensor Nerly Full Sensor Feed-Out Sensor Home Position Sensor Feed-In Sensor Entrnce Sensor Exit Sensor UV Sensor (Upper) UV Sensor (Lower) CIS trnsmissive Sensor CIS Sensor (Lower) CIS Sensor (Upper) Clirtion Tool Requirements Figure 6-30 illustrtes nd list identifies the clirtion Tools nd equipment interconnects necessry to instll n ivizion Unit wy from its Host Mchine. NOTE: When the USB A Terminl connects to the USB Hu, the ivizion my not e operting. Ensure tht the USB A Terminl is properly connected directly to the USB Port of the PC. Figure 6-29 Downlod Completed Screen 2 This completes the ivizion Softwre Downloding Procedures. 6-6

67 Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 ) ivizion Device ) Power Supply c) PC (OS: Windows XP) (ivizion USB Driver Instlled) d) USB Cle d 1 ) USB A Terminl d 2 ) USB Mini-B Terminl e) Appliction Softwre* (JCM Tool Suite Stndrd Edition) f) Reference Pper (KS-072) *. Contins USB Downloder, Sensor Clirtion Performnce Test Progrms nd Utility. Figure 6-30 Remote Clirtion Tools Required Plcing the KS-072 Reference Pper This portion provides informtion concerning the KS-072 Reference Pper s settings nd uses. c ID Sticker e d d 1 d 2 NOTE: Do not touch the Pper Surfces of either side of the KS-072 Reference Pper (See Figure 6-31 ). Top Surfce Figure 6-31 Reding KS-072 Reference Pper Perform the following steps to properly plce the KS-072 Clirtion Reference Pper into the ivizion Device: 1. Open the Upper Guide while pressing in on the Upper Guide Access Levers locted on ech side of the Acceptor Unit tht re indicted y the Blue Arrows in Figure Plce the KS-072 Reference Pper (See Figure 6-32 ) in the Unit until its Ctch Edge reches oth the left nd right side of the Frme (See Figure 6-32 c). NOTE: Plce the KS-072 Reference Pper so the ID Sticker is visile, otherwise, Clirtion will not e correctly performed. Bottom Surfce Open f 3. Firmly close the Upper Guide (See Figure 6-33 ) until it clicks into plce, nd ensure tht oth sides re tightly closed nd locked in plce. Click Click Figure 6-33 Reference Pper Setting 2 Clirtion Procedure The following two (2) methods exist for performing ech of the ivizion Clirtion Procedures: Clirtion Only Clirtion plus Seril Numer Writing. CALIBRATION ONLY Perform the following steps to just clirte the ivizion Unit Sensors: 1. Turn the ivizion Unit s Power Switch OFF. 2. Set DIP Switch #8 to ON (See Figure 6-34). 3. Turn the ivizion Unit s Power Switch ON. The Sttus LED will egin flshing nd then will light stedy Blue Color. Figure 6-34 DIP Switch #8 ON 4. Lunch the JCM Tool Suite Stndrd Edition Appliction. The JCM Tool Suite Stndrd Edition Screen shown in Figure 6-35 will pper when the ppliction ecomes ctive. 5. Mouse-click on, nd hold-down the Service Mode Pull-down Menu Selection (See Figure 6-35 ) nd slide-down to select the Sensor Adjustment from within the Pull-Down Menu (See Figure 6-35 ). c Figure 6-32 Reference Pper Setting 1 Figure 6-35 JCM Tool Suite Stndrd Edition Screen 3 6. This ction will ctivte the ivizion Clirtion Ver.X.XX Mode utomticlly, nd the Screen shown in Figure 6-36 will pper. 6-7

68 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing Once the three (3) Sensor Clirtion Procedures re complete, the Clirtion Informtion Screen shown in See Figure 6-39 will re-pper. Figure 6-36 ivizion Clirtion Ver.X.XX Screen NOTE: Writing Seril No. cn e performed fter Clirtion is completed. To do so, Click on the Updte seril No. Check-ox (See Figure 6-36 ) if the ivizion Device needs its current Seril No. written. NOTE: If the RFID Bord is not fetured within the ivizion Device, remove the check in the Check RFID Check-ox. 7. Mouse-click on the Strt Screen Button (See Figure 6-36 ) to egin the following three (3) sequentil Sensors Clirtion Procedures: ). Csh Box Sensor ). Nerly Full Sensor c). Feed-Out Sensor. Clirtion will e performed in the ove lphetic order while one of either Box RUNNING, Nerly Full RUNNING nd Feed-Out RUNNING messges is showing on the Screen (See Figure 6-37). NOTE: If the Check RFID Check-ox shown in Figure 6-37 is un-checked, the Clirtion Informtion Screen shown in Figure 6-38 will not pper. When present, Mouse-Click on the OK Screen Button to egin the Clirtion Procedure. c Figure 6-39 Clirtion Informtion Screen 2 8. Remove the Csh Box to perform the Home Position Sensor Clirtion Procedure. 9. Open the Csh Box nd press down on the Pusher Relese Plte (See Figure 6-40 & ). Figure 6-40 Pusher Plte Relese Loction 10. Hold the Pusher Plte down (See Figure 6-41 ) nd slide 80x50mm piece of Crdord (See Figure 6-41 ) in etween the Frme Outer LR Guides (Figure 6-41 c) nd the Pusher Plte. Crdord c NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-37 Feed-Out Clirtion Proceeding Screen Figure 6-38 Clirtion Informtion Screen 1 Slide In Figure 6-41 Crdord Setting Loction 11. Reset the Csh Box ck into its Frme position. 12. Mouse-click on the OK Screen Button (Review Figure 6-39 ) to egin the following four (4) Sensor Clirtion Procedures: ). Home Position Sensor ). Feed-In Sensor c). Entrnce Sensor d). Exit Sensor. Clirtion will e performed in the ove lphnumeric order while one of Home Position RUNNING, Feed-In RUNNING, Entrnce RUNNING or Exit RUNNING messges is showing on the Screen (See Figure 6-42). 6-8

69 Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section Remove the KS-072 Reference Pper nd Mouse-click on the OK Screen Button (See Figure 6-45 ) to egin the UV Sensor Non-Pper Clirtion. Once the UV Sensor Non-Pper Clirtion is complete, the Clirtion Informtion Screen shown in Figure 6-46 will re-pper. NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-42 Exit Clirtion Proceeding Screen Once the four (4) Sensors Clirtion Procedures re complete, the Clirtion Informtion Screen shown in Figure 6-43 will re-pper. Figure 6-43 Clirtion Informtion Screen Remove the Csh Box nd remove the piece of Clirtion Crdord, then reset the Csh Box into the ivizion Device gin. 14. Plce Reference Pper KS-072 into the ivizion Device (See Plcing the KS-072 Reference Pper on pge 6-7 of this Section). 15. Mouse-click on the OK Screen Button (See Figure 6-43 ) to egin the following two (2) UV Sensor Clirtion Procedures: ). Lower UV Sensor ). Upper UV Sensor. Clirtion will e performed in the ove lphetic order while UV RUNNING is showing on the Screen (See Figure 6-44). Figure 6-46 Clirtion Informtion Screen Plce the KS-072 Reference Pper ck into the ivizion Device (See Plcing the KS-072 Reference Pper on pge 6-7 of this Section). 18. Mouse-click on the OK Screen Button (See Figure 6-46 ) to egin the following three (3) CIS Sensor Clirtion Procedures: ). CIS Trnsmissive Sensor ). CIS Upper Sensor c). CIS Lower Sensor. Clirtion will e performed in the ove lphetic order while CIS RUNNING is showing on the Screen (See Figure 6-47). NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-47 CIS Clirtion Proceeding Screen Once the CIS Sensor Clirtion is complete, the Clirtion Informtion Screen shown in Figure 6-48 will re-pper. NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-44 UV Clirtion Proceeding Screen Once the UV Sensor Clirtion is complete, the Clirtion Informtion Screen shown in Figure 6-45 will re-pper. Figure 6-48 Clirtion Informtion Screen Remove the KS-072 Reference Pper nd Mouse-click on the OK Screen Button (See Figure 6-48 ) to egin the CIS Sensor Non-Pper Clirtion Procedure. Once the CIS Sensor Non-Pper Clirtion Procedure is complete, the Clirtion Vlue will e written to the EEPROMs locted on the Sensor Bord nd the CPU Bord (See Figure 6-49). Figure 6-45 Clirtion Informtion Screen 4 6-9

70 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing locted t the ottom of the Screen to either increse or decrese the numers, or chnge the existing numers using the or Tringle Button (See Figure 6-52 ). 5. Mouse-click on the OK Screen Button locted on the right side of the Screen (See Figure 6-52 ). NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-49 Clirtion Vlue Writing Screen 20. When the Clirtion Vlue writing EEPROM writing is complete, the Clirtion Informtion Screen shown in Figure 6-50 will re-pper. 21. Mouse-click on the OK Screen Button (See Figure 6-50 ). Figure 6-52 Setting Mnufcture No. Screen The Clirtion Vlue nd the Seril Numer will then e written into the EEPROMs on the Sensor nd the CPU Bords (See Figure 6-53). Figure 6-50 Clirtion Complete Screen This completes the Pper Clirtion Procedures. Refer to Reference Pper Use Precutions on pge 1-3 of Section 1 to properly store nd prevent dmge to the KS-072 Reference Pper. CALIBRATION PLUS SERIAL NUMBER WRITING When the Sensor Clirtion procedure is complete, the cpility to write the Seril Numer into the ivizion Unit ecomes possile. To write Seril Numer into Memory, proceed s follows: 1. Complete the initil Sensor Clirtion Procedure first (See Clirtion Only on pge 6-7 of this Section). NOTE: To perform the Writing Seril No., process, Mouse-Click on the Updte seril No. Check-ox when the ivizion Clirtion Ver.X.XX Screen is ctive (See ivizion Clirtion Ver.X.XX Screen Figure 6-36 on pge 6-8 of this Section). 2. Once the CIS Sensor Clirtion is complete, the ivizion Clirtion Service Suite Edition Screen shown in Figure 6-51 will pper. Figure 6-51 ivizion Clirtion Service Suite Edition Screen 3. Mouse-click on the OK Screen Button (See Figure 6-51 ). The Setting Mnufcture No Screen shown in Figure 6-52 will then pper. 4. Mouse-click on either the or Tringle Indiction Buttons in ech Seril Numer Box NOTE: The Brogrph does not indicte Clirtion in progress. Figure 6-53 Clirtion Vlue Writing Screen When the dt writing into the EEPROM is complete, the Clirtion Informtion Screen shown in Figure 6-54 will re-pper. Figure 6-54 Adjustment Info Screen 8 6. Mouse-click on the OK Screen Button (See Figure 6-54 ). This completes the Seril Numer Writing Procedures. Performnce Tests This portion explins the ivizion Performnce Test Procedures. The following two (2) methods exist to perform this Performnce Test Procedure. Performnce Test using PC Performnce Test using the Externl DIP Switches. Choose one (1) of the two (2) ove Performnce Test Procedures y selecting the one relted to the prticulr circumstnce desired. 6-10

71 Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 Performnce Test Tool Requirement using PC Figure 6-55 illustrtes nd list identifies the Tools nd Equipment Interconnects required to perform PC ivizion Performnce Test. e d d 1 d 2 c ) ivizion Device ) Power Supply c) PC (OS: Windows XP) (ivizion USB Driver Instlled) d) USB Cle d 1 ) USB A Terminl d 2 ) USB Mini-B Terminl e) Appliction Softwre* (JCM Tool Suite Stndrd Edition) *. Contins USB Downloder, Sensor Clirtion, Performnce Test progrms nd Utility. Figure 6-55 PC Performnce Test Tools Required Performnce Test Items using PC Tle 6-2 lists the ville Performnce Test Items nd their purpose using PC for testing. Tle 6-2 PC Performnce Test Items PC Performnce Test Preprtion Perform following steps to egin the Performnce Test Preprtion Procedure: 1. Turn the ivizion Unit s Power Switch OFF. 2. Remove the Trnsport Unit from the Frme. 3. Set 8-Position DIP Switch #8 to ON. Figure 6-56 DIP Switch #8 Set ON 4. Plce the Trnsport Unit into the Frme. 5. Turn the ivizion Unit s Power Switch ON. The Sttus LED will light stle Blue Color. 6. Lunch the JCM Tool Suite Stndrd Edition Appliction. The Screen shown in Figure 6-57 will pper when the ppliction ecomes ctivte. 7. Mouse-click on, nd hold-down the Service Mode selection pull-down Menu (See Figure 6-57 ) nd Slide-down select Performnce Test from the Pull-Down Menu Sections (See Figure 6-57 ). No. Test Item Test Purpose Motor Norml Rottion Motor Reverse Rottion Stcker Motor Cycle Movement Sttus LED Indiction Sensor ON/OFF DIP Switch ON/OFF Bnknote Acceptnc e ICB Setting (Reding Ticket) Testing the Trnsport Motor rottion in Bnknote intke direction Testing the Trnsport Motor rottion in Bnknote reject direction Testing the Stcker Motor s movement Testing sequentil movement from Bnknote trnsporttion to stcking t regulr intervls without Bnknotes Testing the Sttus LED Indictions Testing ech Sensor s Performnce Testing the 8-Position DIP Switches Performnce Testing Trnsporttion, Vlidtion, Stcking nd Reject Performnce, nd the Vend Signl Output Checking the ICB Enle/Disle Setting of the ICB Mchine No. Stndy Blue Lit Blue Lit Sttus LED Operting Yellow Flshes Red Green Blue Blue Lit Extinguished (Out) Figure 6-57 JCM Tool Suite Stndrd Edition Screen 8. Activte the ivizion Test Item VerX.XX Appliction nd the Screen shown in Figure 6-58 will utomticlly pper. c f i g h Figure 6-58 ivizion Test Item VerX.XX Screen d e 6-11

72 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing 9. Mouse-click on ech Screen Button to egin its relted Performnce Test. A Screen similr the Screen shown in Figure 6-59 will pper for ech Test. For more detil concerning ech Performnce Test, refer to Performnce Test Items using PC on pge 6-11 of this Section. c c Figure 6-60 Trnsport Motor Norml Forwrd Test Screen Tle 6-3 lists the Sttus LED indictions for ech norml or norml Test Item condition. Tle 6-3 LED Indictions for ech condition Figure 6-59 Strt, Stop & Exit Screen Button 10. Mouse-click on the relted Strt Screen Button (See Figure 6-59 ) to egin the desired Performnce Test. When ll of the desired Performnce Tests re complete, Mouse-click on the Stop Screen Button (See Figure 6-59 ). If return to the Test Item Select Screen is desired, Mouse-click on the Exit(C) Screen Button (See Figure 6-59 c). Performnce Test Procedures This portion provides informtion concerning ech Performnce Test Procedure. ANY MOTOR TEST Perform the following steps to test the Trnsport Motor s Norml Forwrd Rottion, the Trnsport Motor s Reverse Rottion, nd the Stcker Motor s opertion with complete Cyclic Movement Test. The following four (4) Motor Tests ville: Trnsport Motor Norml Forwrd Rottion Test Trnsport Motor Reverse Rottion Test Stcker Motor Test Cyclic Movement Test. To run specific Test, proceed s follows: 1. Lunch the Test Item Select Screen (Refer to the PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the desired Test Screen Button from the Menu Screen provided (Refer ck to Figure 6-58,, c & d). 3. Mouse-click on the Strt Screen Button (Refer ck to Figure 6-60 ) to egin ech Test. 4. Check tht the Sttus LED is linking t Yellow Color rte. (See Tle 6-3 to identify the vrious Sttus LED conditions). 5. Mouse-click on the Stop Screen Button (See Figure 6-60 ) to end ech Test. 6. Mouse-click on the Exit Screen Button (See Figure 6-60 c) to return to the Test Item Select Screen. Test Item Trnsport Motor Norml Forwrd Rottion Trnsport Motor Reverse Rottion Stcker Motor Cyclic Movement * Screen Button Trnsport motor Forwrd Trnsport motor Reverse Stcker motor Forwrd Cycle Test Norml Yellow Flshes Sttus LED Anorml Lit Yellow or Extinguished (Out) Red Flshes *. Once the Cycle Movement Test is complete, trnsport movement will hlt for pproximtely 25 seconds; then re-egin the test gin. (See Error, Jm nd Reject Code Tles on pge A-2 of Appendix A in this Service Mnul when the Sttus LED indictes n norml operting condition). LED INDICATOR TEST Perform the following steps to test the LED Indictors. 1. Lunch the Test Item Select Screen gin (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the Disply Test Screen Button (See Figure 6-58 e). 3. Mouse-click on the Strt Screen Button (See Figure 6-61 ) to egin the LED Indictor Test. c Figure 6-61 LED Indictor Test Screen 6-12 KF srl Phone

73 KF srl Phone Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 4. Check the Sttus LED s condition. When the Sttus LED Indictor links in Red, Green, nd Blue Color sequence, the Sttus LED is performing normlly. 5. Mouse-click on the Stop Screen Button (See Figure 6-61 ) to end the LED Indictor Test. 6. Mouse-click on the Exit Screen Button (See Figure 6-61 c) to return to the Test Item Select Screen. SENSOR ON/OFF TEST Perform the following steps to perform the Sensor ON/OFF Test. 1. Lunch the Test Item Select Screen gin (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the Sensor ON/OFF Test Screen Button (See Figure 6-58 f). 3. Mouse-click on the Strt Screen Button (See Figure 6-62 ) to egin the Sensor ON/OFF Test. The current testing condition is indicted in column djcent to the Function eing tested on the Figure 6-62 Screen. c Figure 6-62 Sensor ON/OFF Test Screen Five (5) ctions re required to check ll twelve (12) Sensors in the ivizion Unit. Refer to Tle 6-4 for ech ction regrding the relted Sensor eing tested. When the desired test ction is complete, the resulting condition of ech Sensor is indicted y its Screen condition turning ON. Tle 6-4 Sensor Actions nd Conditions Action Sensor Condition Open the Acceptor Unit s Upper Guide Open the Trnsport Unit s Upper Guide No Action Required (Set the Csh Box correctly in plce) Remove the Csh Box from the Unit Entrnce CIS L2 CLS L1 CIS R1 CIS R2 Exit Feed-In Feed-Out Csh Box (Lrge Csh Box or Stndrd Csh Box) Nerly Full OFF ON OFF ON OFF ON OFF ON Tle 6-4 Sensor Actions nd Conditions (Cont.) Hold-down the Pusher Plte nd slide 80x50mm piece of Crdord in-etween the Frme Home Position OFF ON Outer LR nd the Pusher Plte * *. Review Figure 6-40 nd Figure 6-41 on pge 6-8 regrding how to set the Crdord in plce. 4. Mouse-click on the Stop Screen Button (See Figure 6-62 ) to end the Sensor ON/OFF Test. 5. Mouse-click on the Exit Screen Button (See Figure 6-62 c) to return to the Test Item Select Screen. BANKNOTE ACCEPTANCE TEST Perform the following steps to test the trnsporttion, vlidtion, stcking nd reject sequentil performnce nd Vend Signl Output functions of the ivizion Unit. 1. Lunch the Test Item Select Screen gin (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the Accept Test Screen Button (See Figure 6-58 g). 3. Mouse-click on the Strt Screen Button (See Figure 6-63 ) to egin the Bnknote Trnsport Test. 4. Insert Bnknote into the ivizion Unit. The Bnknote s Denomintion will e indicted on Screen similr to Figure 6-63d. c Action Sensor Condition Figure 6-63 Denomintion Indiction Loction Tle 6-5 Denomintion Vlution List Denomintion Vlue Indiction $1 1 $5 5 $10 10 $20 20 $50 50 $ Mouse-click on the Stop Screen Button (See Figure 6-63 ) to quit from the relted Test Screen. 6. Mouse-click on the Exit Screen Button (See Figure 6-63 c) to return the Test Item Select Screen. d 6-13 KF srl Phone

74 KF srl Phone Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing NOTE: If the intent is to perform other tests, close ll of the Screens open on the PC, nd turn the ivizion Power Switch OFF; then, Turn the ivizion Power Switch ck ON, nd re-egin the Performnce Test Procedures over gin. ICB FUNCTION SETTING (BARCODE COUPON) Perform the following steps to set the ICB Enle/ Disle Functions when using Brcode Coupon. To enle the ICB function: 1. Lunch the Test Item Select Screen gin (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the ICB Control Ticket Red Test Screen Button (See Figure 6-58 h). 3. Mouse-click on the Strt Screen Button (See Figure 6-64 ) to egin the ICB Function Setting. c Figure 6-64 ICB Function Test Screen 4. Insert n ICB Enle Ticket Brcode Coupon. The Sttus LED will link three (3) times t Green Color rte when the ICB Enle Ticket is eing red correctly. 5. Once the Sttus LED egins linking normlly, insert JCM Glol Brcode Coupon in order to configure the Mchine Numer for the ivizion Unit eing tested. The Sttus LED will link three (3) times t Green Color rte when the Mchine Numer is eing red correctly. If the Sttus LED links t Blue Color rte, n error condition hs occurred (See Error, Jm nd Reject Code Tles on pge A-2 of Appendix A in this Service Mnul for more detils). 6. Mouse-click on the Stop Screen Button (See Figure 6-64 ) to complete the ICB Function Setting opertion. 7. Mouse-click on the Exit Screen Button (See Figure 6-64 c) to return to the Test Item Select Screen. NOTE: If the intent is to perform other tests, close ll of the Screens open on the PC, nd turn the ivizion Power Switch OFF; then, Turn the ivizion Power Switch ck ON, nd re-egin the Performnce Test Procedures over gin. To disle the ICB function: 1. Lunch the Test Item Select Screen (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section). 2. Mouse-click on the ICB Control Ticket Red Mode Screen Button (See Figure 6-58 h). 3. Mouse-click on the Strt Screen Button (See Figure 6-64 ) to egin the ICB Function Setting opertion. 4. Insert n ICB Disle Ticket Brcode Coupon. The Sttus LED will link three (3) times t Green Color rte when the ICB Disle Ticket reding is properly completed. If the Sttus LED is links t Blue Color rte, some error condition hs occurred (See Error, Jm nd Reject Code Tles on pge A-2 of Appendix A in this Mnul for more detils). 5. Mouse-click on the Stop Screen Button (See Figure 6-64 ) to finish the ICB Function Setting opertion. 6. Mouse-click on the Exit Screen Button (See Figure 6-64 c) to return to the Test Item Select Screen. NOTE: If the intent is to perform other tests, close ll of the Screens open on the PC, nd turn the ivizion Power Switch OFF; then, Turn the ivizion Power Switch ck ON, nd re-egin the Performnce Test Procedures over gin. DIP SWITCH ON/OFF TEST Perform following steps to test the 8-Position DIP Switch ON/OFF Functions: 1. Turn the ivizion Power Switch to OFF. 2. Remove the Trnsport Unit from the ivizion Unit s upper Section. 3. Set the desired DIP Switches eing tested to ON nd set DIP Switch #8 to ON. DIP Switch #8 will lwys e set to ON during ll remining Switch Tests eing performed (The Figure 6-65 exmple shows DIP Switch #3 nd #5, plus DIP Switch #8 ll set to ON). c SW8 is Alwys ON During Performnce Test Figure 6-65 DIP Switch ON/OFF Test Screen 1 4. Lunch the Test Item Select Screen (Refer to PC Performnce Test Preprtion on pge 6-11 of this Section) KF srl Phone

75 KF srl Phone Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 5. Mouse-click on the DIP Sw ON/OFF Test Screen Button (Review Figure 6-58 i) to egin the DIP Switch ON/OFF Test. 6. Mouse-click on the Strt Screen Button (See Figure 6-65 ). The tested DIP Switch condition will e indicted on the Screen similr to tht shown in Figure Mke sure the desired DIP Switch Numer is shown s ON. NOTE: If DIP Switch #3 nd #5 were set during previous procedure, the Screen will indicte ON in ech Field Window relted to their DIP Switch Numer. 7. Set the desired DIP Switch to OFF (Figure 6-65 exmple = DIP Switch #3 nd #5). 8. Mke sure the desired DIP Switch Numer is OFF. (If DIP Switch #3 nd #5 were set during previous procedure, the Screen will indicte ON in ech Field Window relted to their DIP Switch Numer). c SW8 is Alwys ON During Performnce Test Figure 6-66 DIP Switch ON/OFF Test Screen 2 9. Mouse-click on the Stop Screen Button (See Figure 6-65 ) to end the DIP Switch ON/ OFF Test. 10. Mouse-click on the Exit Screen Button (See Figure 6-65 c) to return to the Test Item Select Screen. 11. Turn the ivizion Power Switch OFF. 12. Plce the Trnsport Unit onto the Frme. NOTE: If it is necessry to perform nother test, mke sure tht DIP Switch No.8 is still set to ON. Performnce Test Tool Requirement using n Externl DIP Switch Box Figure 6-67 illustrtes nd list identifies the Tools nd equipment interconnects necessry to perform the ivizion Performnce Tests using n Externl Switch Box. Externl DIP Switch Performnce Test Procedure Settings Tle 6-2 lists the DIP Switch settings for the Performnce Tests using the Externl Switch Box. Tle 6-6 Performnce Test DIP Switch Settings * No Test Item Motor Norml Forwrd Rottion Motor Reverse Rottion Stcker Motor Cyclic Movement Sttus LED Indiction ICB Setting (Reding Ticket) d Sttus LED Blue Lit MOLEX 4-Pin MOLEX 3-Pin MOLEX 2-Pin ) ivizion Device ) Power Supply (12V DC - 24V DC) c) Externl Switch Box (User provided) d) Interfce Cle ( EDP#146780) Figure 6-67 Clirtion Tool Requirements Stndy Operting Yellow Flshes Red Green Blue Bnknote Acceptnce Extinguished (Out) DIP Switch Setting (O = ON) O O O O O - - O O O O O - - O O O O O O O - - O O *. NOTE: The Sensor ON/OFF Test nd the DIP Switch ON/OFF Test re ONLY ville when using the PC procedure! Performnce Tests using the Externl DIP Switch Procedures Perform the following steps to test the Motor Norml Forwrd nd Reverse Rottion, the Stcker Motor, the Cyclic Movement Test, the Sttus LED Indiction Test, the Bnknote Trnsporttion nd the ICB Function Setting Performnce Tests. 1. Turn the ivizion Power Switch OFF. 2. Remove the Trnsport Unit from the Frme. 3. Set the desired DIP Switch Numer to ON using the 8-Position DIP Switch (See Tle 6-6). 4. Plce the Trnsport Unit ck onto the Frme. 5. Connect the third the fourth Pin Connector of the Externl Switch Box Cle to the corresponding Connectors Pins of the five (5) Pin Plug locted t the rer side of the ivizion Trnsport Unit c 6-15 KF srl Phone

76 KF srl Phone Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing 6. Set the Externl Switch Box Switch to the position wy from the Sttus LED on the Box. 7. Turn the ivizion Power Switch to ON. The ivizion Sttus LEDs will indicte Stnd-y Mode when the Sttus LED on the ivizion Lights stedy Blue Color, nd the Sttus LED on the Externl Switch links t Red Color rte. 8. Turn the Externl Switch Box Switch towrd the ivizion sttus LED on the Box when the ivizion Power Switch is turned to ON. The desired Test selected y DIP Switch Positions will then egin (Refer to Performnce Test Procedures on pge 6-12 of this Section for ech test nd its resulting Test indiction). 9. Return the Externl Switch Box Switch to the position wy from the ivizion Sttus LED on the Box gin, nd the current Test eing run will end. If other Switch Box Tests re necessry, restrt from Step 1 t the eginning of this procedure. ivizion Utility Tools This portion provides informtion regrding ech ivizion Service Mode setting procedure. The following two (2) Tool setting types exist when using the ivizion Utility Tools: CIS Imge Views ICB Function Settings. ICB/Imge Setting Tool Requirements The Tools listed in Figure 6-68 re required to set or chnge ech ivizion ICB Setting. e c d d 1 d 2 ) ivizion Device ) Power Supply c) PC (OS: Windows XP/iVIZION USB Driver Instlled) d) USB Cle d 1 ) USB A Terminl Plug d 2 ) USB Mini-B Terminl Plug e) Appliction Softwre* (JCM Tool Suite Stndrd Edition). *. Contining USB Downloder, Sensor Clirtion, Performnce Test progrms nd Utility. Figure 6-68 ICB Setting Tool Requirements ICB/Imge Setting Chnge Preprtion Perform the following steps to set or reset the ICB Functions. 1. Turn the ivizion Unit s Power Switch to ON. 2. Lunch the JCM Tool Suite Stndrd Edition Appliction. The Figure 6-69 Screen will pper when the ppliction ecomes ctivte. 3. Mouse-click on, nd hold-down on the Service Mode selection Pull-down Menu (See Figure 6-69 ), nd Slide-down select Utility from the Pull-Down Menu Sections (See Figure 6-69 ). The ivizion Utility Tool Version X.XX for Suite Edition Appliction Menu selection Screen shown in Figure 6-70 will utomticlly pper. Figure 6-69 JCM Tool Suite Stndrd Edition CIS Imge Tool The CIS Imge Tool provides grphic views of the scnned Bnknote imges directly. This feture is ville to confirm the lst stcked Bnknote denomintion y presenting its scnned front nd ck imges. 1. Mouse-click on the lrge 1) CIS IMAGE Screen Button locted on the ivizion Utility Tool Screen (See Figure 6-70 ). 2. Confirm tht the CIS Imge Screen shown in Figure 6-71 ppers. 3. Mouse-click on the Red Screen Button (See Figure 6-72 ) to see n imge of the lst scnned Bnknote s upper nd lower surfce imges on the Screen (See Figure 6-72 & c). 4. Mouse-click on the File Sve Screen Button (See Figure 6-71 ) if necessry to sve the dt. 5. Mouse-click on the File Red Screen Button (See Figure 6-71 c) to retrieve the sved file dt. NOTE: The ICB Function Sttus is initilly Fctory Set to INHIBIT s stndrd function. Therefore, the ivizion Unit s ICB must e first initilized using the USB Tool Suite Utility Options. Refer to the JCM ICB Instlltion Guide for exct progrmming descriptions nd opertionl detils KF srl Phone

77 KF srl Phone Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 SETTING ICB ENABLE/DISABLE FUNCTIONS The following portion explins ech ICB setting when ctivted: 1. Mouse-click on the lrge 2) ICB SETTING Screen Button (See Figure 6-73 ) locted on the ivizion Utility Tool Screen. Figure 6-70 ivizion Utility Tool Version X.XX for Suite Edition Screen 1 Figure 6-71 Empty CIS IMAGE Screen c Figure 6-73 ivizion Utility Tool Version X.XX for Suite Edition Screen 2 2. Confirm tht the ICB Function Screen shown in Figure 6-74 ppers (See Figure 6-74). Seven (7) Screen Buttons exist on this Screen. To egin using the ICB Function Screen Buttons, select the ICB Enle / Disle Function desired y first Mouse-clicking on the pproprete Screen Button (See Figure 6-74 & ). Figure 6-72 Lst Acceptnce CIS IMAGE Screen NOTE: The CIS Imge dt will not e retined if the ivizion s Power Supply is turned OFF fter stcking the lst Bnknote! ICB Function Setting This portion provides informtion out ech Screen Button locted on the ICB Function Screen shown in Figure The following three (3) setting types re ville for use with the ICB Functions: Setting the ICB Enle/Disle Function Setting the Mchine Numer Setting the ICB Inhiit Function. c Figure 6-74 ICB Function Screen Enle Screen Button Activtion Set the ICB Enle Function when n RFID Circuit Bord exists on the ivizion Unit. However, if the Csh Box IS SET to System Inhiit condition, or the RFID Circuit Bord IS NOT present, the Sttus LED will flsh t Blue Color rte to notify tht n error exists (See Tle 6-7 on pge 6-19 of this Section to resolve this issue). To set ICB Enle proceed s follows: 1. First, confirm tht the Csh Box setting IS NOT set to System Inhiit ; then Mouse-click on the Enle Screen Button (See Figure 6-74 ) to ctivte the ICB Function. 2. When the ICB Function is correctly enled, the ICB Successfully Enled. pop-up Dilog Messge Window shown in Figure 6-75 will pper. 3. Mouse-click the OK Screen Button (See Figure 6-75 ) to ccept the reported messge KF srl Phone

78 KF srl Phone Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing Setting the M/C # Figure 6-75 Enle Setting Completion Disle Screen Button Activtion Set the ICB Disle Function when n RFID Circuit Bord DOES NOT exist on the ivizion Unit. However, if the Csh Box IS SET to System Inhiit condition, or the RFID Circuit Bord IS present, the Sttus LED will flsh t Blue Color rte to notify tht n error exists (See Tle 6-7 on pge 6-19 of this Section to resolve this issue). To set ICB Disle proceed s follows: 1. First, confirm tht the Csh Box setting is not lredy set to System Inhiit ; then Mouse-Click on the Disle Screen Button (See Figure 6-74 ) to inhiit the ivizion s ICB Function. 2. When the ICB Function is correctly disled, the ICB Successfully Disled pop-up Dilog Messge Window shown in Figure 6-76 will pper. 3. Mouse-click the OK Screen Button (See Figure 6-76 ) to ccept the reported messge. This setting llows the individul fourteen (14) digit Mchine Code Numer on the ivizion to e entered. The Mchine Numer helps to identify to which Gme Mchine the ivizion elongs, nd voids using its Csh Box for use in nother Gme Mchine. To enter nd set Mchine Code Numer, proceed s follows: 1. Type the fourteen (14) Mchine Code Numer in the Text Field Window locted next to the Set M/C Screen (See Figure 6-78 ). 2. Mouse-click on the Set M/C Screen Button (See Figure 6-78 ) to set the Mchine Numer. Figure 6-78 Mchine Numer Setting NOTE: When the Mchine Code Numer is less thn fourteen (14) digits in length, dd zeros 0 to the hed of the Mchine Numer in order to crete recognizle 14 digit Code Numer. 3. When the Mchine Numer is correctly set, the M/C# Set Successfully pop-up Dilog Messge Window shown in Figure 6-79 will pper. 4. Mouse-click the OK Screen Button (See Figure 6-79 ) to ccept the reported messge. Figure 6-76 Disle Setting Completion ICB Current Sttus Screen Button To check the current ICB Enle/Disle Setting Sttus proceed s follows: 1. Mouse-click on the ICB Current Sttus Screen Button (See Figure 6-77 ). 2. The Current ICB Enle/Disle Sttus will pper in Field Window next to the ICB Current Sttus Screen Button (See Figure 6-77 ). Figure 6-79 Mchine Numer Setting Completion To retrieve the current Mchine Code Numer set in n ivizion Unit proceed s follows: 1. Mouse-click on the Get M/C Screen Button (See Figure 6-80 ). 2. The existing fourteen (14) Mchine Code Numer will pper in the Text Field Window locted next to the Get M/C Screen Button (See Figure 6-80 ). Figure 6-80 Mchine Numer Indiction Figure 6-77 ICB Current Sttus Screen 6-18 KF srl Phone

79 KF srl Phone Clirtion nd Testing ivizion SeriesNext-Genertion Bnknote Acceptor Unit Section 6 Setting Inhiit ICB System To record n ICB Function Inhiit setting in the Csh Box when n ivizion Unit RFID Circuit Bord exists, proceed s follows: 1. Mouse-click on the Inhiit Screen Button (See Figure 6-81 ). To retrieve the current ICB Function Setting in Csh Box proceed s follows: 1. Mouse-click on the Get ICB System Sttus Screen Button (See Figure 6-80 ). 2. The existing ICB Inhiit Function set in the Csh Box will pper in the pop-up Dilog Messge Window next to the Get ICB System Sttus Screen Button (See Figure 6-80 ). Figure 6-81 Inhiit Screen Button Loction NOTE: The JCM Fctory Defult Setting is Inhiit (See Tle 6-7). 2. When the ICB Inhiit Function in Csh Box is properly set, the ICB Inhiition Successfully pop-up Dilog Messge Window shown in Figure 6-82 will pper. 3. Mouse-click on the OK Screen Button (See Figure 6-82 ) to ccept the reported messge. Figure 6-83 ICB System Sttus Indiction ICB Function Opertionl Condition Tle 6-7 lists vrious functionl comintions ville for the ivizion Unit, RFID Bord, Csh Box nd ICB Function Settings (Refer to Error, Jm nd Reject Code Tles on pge A-2 of Appendix A in this Mnul for more detils concerning ech error type). Figure 6-82 Inhiit Setting Completion Tle 6-7 ICB Setting Function Opertionl Condition ivizion RFID Bord Csh Box Initiliztion Csh Box Instlled the sme Mchine Instlled nother Mchine Red/Write Tool Dt Correction Checksum Errors Enle Instlled NOT System Inhiit OK OK Not Aville Not Aville Not Aville System Inhiit Not Aville Not Aville Not Aville Not Aville Not Aville NOT Instlled - Not Aville Not Aville Not Aville Not Aville Not Aville Disle Instlled NOT System Inhiit Not Aville Not Aville Not Aville Not Aville Not Aville System Inhiit OK OK OK OK OK NOT Instlled - OK OK OK OK OK 6-19 KF srl Phone

80 Section 6 ivizion SeriesNext-Genertion Bnknote Acceptor Unit Clirtion nd Testing THIS PAGE INTENTIONALLY LEFT BLANK 6-20

81 ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 7 EXPLODED VIEWS & PARTS LISTS This section provides product exploded views nd prts lists for the ivizion Next-Genertion Bnknote Acceptor Unit. This section contins the following informtion. ivizion Entire Unit View nd Prts List ivizion Entire Unit Exploded View ivizion Vlidtion Unit Exploded View ivizion Trnsport Unit Exploded View ivizion Frme Unit Exploded View ivizion Csh Box Unit Exploded View ivizion Option Unit Exploded View. Figure 7-1 ivizion Entire Unit Exploded View Digrm 7-1

82 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Entire Unit Prts List Tle 7-1 ivizion Entire Unit Prts List Ref No. EDP No. Description Qty Remrk ivizion Vlidtion Unit ivizion Trnsport Unit ivizion Frme Unit ivizion Csh Box (S) ivizion Csh Box (L) ivizion LD Frme Unit 1 See Tle 7-2 through Tle 7-4 for detils regrding the Vlidtion Unit Prts See Tle 7-5 through Tle 7-10 for detils regrding the Trnsport Unit Prts See Tle 7-11 for detils regrding the Frme Unit Prts See Tle 7-12 through Tle 7-14 for detils regrding the Csh Box Unit Prts See Tle 7-15 for detils regrding the LD Frme Unit Prts 7-2

83 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Vlidtion Unit 1 Exploded View Figure 7-2 ivizion Vlidtion Unit 1 Exploded View 7-3

84 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Vlidtion Unit 1 Prts List Tle 7-2 ivizion Vlidtion Unit 1 Prts List Ref No. EDP No. Description Qty Remrk ivizion Hed Cover A ivizion Hed Cover B Hed Open Stopper Grounding Plte A Stopper Fulcrum Pin Stopper Pin ivizion Sticker Phillips, Self Tightening, Binding 3M Screw M Pn Hed Screw with W Wsher 3M Vlidtion Seril Lel 1 7-4

85 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Vlidtion Unit 2 Exploded View Figure 7-3 ivizion Vlidtion Unit 2 Exploded View 7-5

86 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Vlidtion Unit 2 Prts List Tle 7-3 ivizion Vlidtion Unit 2 Prts List Ref No. EDP No. Description Qty Remrk ivizion Hed Frme B ivizion Hed Bill Guide 85B Hed Open Ltch A Hed Open Ltch B Roller Arm Front Roller Arm Rer ivizion Hed Roller Roller Arm Shft Hed Roller Shft Spring Arm Rer Spring Arm Front Upper UV FPC Upper CIS FFC Trnsmissive Light FFC Vlidtion Sensor FPC Sensor Rely Bord Assy CIS Upper UV Sensor Trnsmissive Light Phillips Strict, Self Tightening, Binding 3M Screw (Blck) Phillips, Self Tightening, Binding 3M Screw Phillips, Self Tightening, Binding 3M Screw (Blck) CIS Prtner 1 7-6

87 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Vlidtion Unit 3 Exploded View Figure 7-4 ivizion Vlidtion Unit 3 Exploded View 7-7

88 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Vlidtion Unit 3 Prts List Tle 7-4 ivizion Vlidtion Unit 3 Prts List Ref No. EDP No. Description Qty Remrk ivizion Hed Frme A ivizion Hed Bill Guide 85A Hed Drive Frme Hed D-Frme Cover A Hed D-Frme Cover B Bezel Hold Chips A Bezel Hold Chips B Exit Sensor Prism Entrnce Prism Bill Guide Push Pin Hed Drive Ger Pulley Hed Idler Pulley Hed Idler Pulley Hed Drive ivizion Hed Roller Spring Bill Guide Push Pin Hed Drive Shft Hed Pulley Pin Timing Belt (Eco Specifictions) Lower UV FFC Lower CIS FFC Vlidtion Sensor Bord Assy CIS Lower UV Sensor M2.6 5 Phillips, F-Lock Binding 3M Screw Phillips Strict, Self Tightening, Binding 3M Screw (Blck) Phillips Strict, Self Tightening, Lminte M3 Screw II (TORX) Phillips, Self Tightening, Binding 3M Screw Phillips, Self Tightening, Binding 3M Screw (Blck) M2.6 8 Flthed, Phillips, Self Tightening 3M Screw x10 Phillips, Self Tightening 3M Screw (Blue) Pn Hed Screw with W Wsher 3M CIS Prtner 1 7-8

89 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 1 Exploded View Figure 7-5 ivizion Trnsport Unit 1 Exploded View 7-9

90 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 1 Prts List Tle 7-5 ivizion Trnsport Unit 1 Prts List Ref No. EDP No. Description Qty Remrk Trnsport Side Cover A Trnsport Side Cover B Trnsport Removl Arm A Trnsport Removl Arm B Side Sensor Cover Side Sensor Prism Connector Plte Trnsport GND Plte Spring Trnsport Ltch Interfce Connector Bord Assy Home Position Sensor Bord Assy USB FPC Power Supply FPC Interfce FPC Home Position Sensor FFC Phillips, Self Tightening, Binding 3M Screw Phillips, Self Tightening, Truss Hed 3M Screw Phillips, Self Tightening, Pn Hed 3M Screw Phillips, Self Tightening, Binding 3M Screw M2.6 4 Pn Hed Screw with W Wsher 3M M Pn Hed Screw with W Wsher 3M Φ Prllel Pin Sustiner (Hrd) Φ4 E-Ring

91 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 2 Exploded View Figure 7-6 ivizion Trnsport Unit 2 Exploded View 7-11

92 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 2 Prts List Tle 7-6 ivizion Trnsport Unit 2 Prts List Ref No. EDP No. Description Qty Remrk Trnsport UP Frme Trnsport UP-Bill Guide Cover Bill Guide Open-Close Lever Trnsport Light Guide D Fixer Roller Shft Trnsport Light Guide F Trnsport Light Guide G Cover Prism Home Position Sponge Roller Trnsport Roller Core Bill Guide Open-Close Shft UP-Bill Guide Roller Shft Bill Guide Fulcrum Pin Spring Bill Guide Open-Close Phillips, Self Tightening, Truss Hed 3M Screw Phillips, Self Tightening, Binding 3M Screw Flthed, Phillips, Self Tightening 3M Screw Φ Plin Wsher Φ3 E-Ring

93 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 3 Exploded View Figure 7-7 ivizion Trnsport Unit 3 Exploded View 7-13

94 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 3 Prts List Tle 7-7 ivizion Trnsport Unit 3 Prts List Ref No. EDP No. Description Qty Remrk Trnsport Bottom Cover Hed Ltch Cover Hed Ltch Button Hed Removl Ltch A Hed Removl Ltch B Trnsport Removl Lever Trnsport Light Guide A Trnsport Light Guide B Trnsport Light Guide C Trnsport Light Guide H Prism Cover Feed Out Sensor Front Msk Trnsport UC Insulting Sheet Trnsport Removl Ltch Fixer Hed Ltch Spring Hed Removl Shft Trnsport Unit Ltch Fulcrum Pin Spring Hed Button Spring Hed Ltch Noise Shielding Sticker Vlidtion Unit Hrness Floting Collr Phillips, Self Tightening, Binding 3M Screw Flthed, Phillips, Self Tightening 3M Screw Flthed, Phillips, Self Tightening 3M Screw (Blck) Phillips, Self Tightening, Binding 3M Screw (Blck) Φ Plin Wsher Φ1.6 8 Prllel Pin Sustiner (Hrd) Φ3 16 Prllel Pin Sustiner (Hrd) Φ3 E-Ring Trnsport Seril Lel Phillips, Self Tightening, Pn Hed 3M Screw x 5 Rmimte 3M Screwwith Lock Pending Br Code Lel

95 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 4 Exploded View Figure 7-8 ivizion Trnsport Unit 4 Exploded View 7-15

96 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 4 Prts List Tle 7-8 ivizion Trnsport Unit 4 Prts List Ref No. EDP No. Description Qty Remrk Trnsport Min Frme Trnsport Light Guide E PCB Supporter FPC Cover Fixer Ger Shft A Fixer Ger Shft B SG Plte Ger Hed Connection Hed Connection Shft Vlidtion CPU Bord Assy Control CPU Bord Assy Phillips, Self Tightening, Binding 3M Screw (Blck) Phillips, Self Tightening, Binding 3M Screw Phillips, Self Tightening, Binding 3M Screw (Blck) Flthed, Phillips, Self Tightening 3M Screw Phillips, Self Tightening, Binding 3M Screw (Blue) M2.6 6 Pn Hed Screw with W Wsher 3M RFID Module Extended Memory Bord Assy 64M it (totl 128M it) 1 Pending Extended Memory Bord Assy 128M it (totl 192M it) RFID Hrness RFID Insulting Sheet Phillips, Self Tightening, Binding 3M Screw

97 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 5 Exploded View Figure 7-9 ivizion Trnsport Unit 5 Exploded View 7-17

98 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 5 Prts List Tle 7-9 ivizion Trnsport Unit 5 Prts List Ref No. EDP No. Description Qty Remrk Drive Module Frme A ivizion Reel A ivizion Reel B Ger Stck Ger Stck Ger Stck Ger Trnsport-Stcking Ger Trnsport-Stcking Ger Box Connection Ger Trnsport-Stcking Motor Ger Hed Connection Pulley Hed Idler Pulley Reel Pulley Trnsport Drive Pulley Hed Connection Pulley Idler Outside Ger Shft Bering Timing Belt (Eco Specifiction) Interrupter Bord Assy Interrupter Hrness M2.6 5 Flthed, Phillips, F-Lock 3M Screw M2.6 8 Phillips, F-Lock Binding 3M Screw (Blue) Phillips, Self Tightening, Truss Hed 3M Screw Phillips, Self Tightening, Binding 3M Screw (Blck) Φ2 E-Ring Φ3 E-Ring Φ1.6x8 Prllel Pin Sustiner (Hrd) Φ3.1x6x1.0 Poly Vinyl Slider Motor Assy

99 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Trnsport Unit 6 Exploded View Figure 7-10 ivizion Trnsport Unit 6 Exploded View 7-19

100 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Trnsport Unit 6 Prts List Tle 7-10 ivizion Trnsport Unit 6 Prts List Ref No. EDP No. Description Qty Remrk Drive Module Frme B Trnsport Ger Stilizer ivizion Reel A Ger Trnsport-Stcking Ger Trnsport-Stcking Ger Box Connection Ger Pulley Drive Ger Trnsport-Stcking Motor Ger Trnsport Ger Trnsport Ger Trnsport Pulley Hed Idler Pulley Reel Pulley Trnsport Drive Pulley Hed Connection Pulley Idler Roller Belt Stopper Reel Shft Trnsport Drive Shft Hed Connection Shft Outside Ger Shft Ger Module Shft Ger Module Shft Ger Module Shft Belt Stopper Roller Pin Bering Timing Belt (Eco Specifictions) M2.6 5 Flthed, Phillips, F-Lock 3M Screw M2.6 8 Phillips, F-Lock Binding 3M Screw (Blue) Phillips, Self Tightening, Binding 3M Screw (Blck) Φ2 E-Ring Φ3 E-Ring Φ1.6 8 Prllel Pin Sustiner (Hrd) Motor Assy

101 Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion SS Version Frme Unit Exploded View Figure 7-11 ivizion SS Version Frme Unit Exploded View 7-21

102 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion SS Version Frme Unit Prts List Tle 7-11 ivizion SS Version Frme Unit Prts List Ref No. EDP No. Description Qty Remrk Frme Bse Frme Bse Guide Frme Spring Plte Frme FG Plte Frme Guide L Frme Guide R Frme Ltch Frme Compression Spring M2.6 4 Flthed, Phillips, 3M Screw Flthed, Phillips, Self Tightening, 3M Screw M2.6 Nylon Nut

103 KF srl Phone Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Csh Box Unit 1 Exploded View Figure 7-12 ivizion Csh Box Unit 1 Exploded View 7-23 KF srl Phone

104 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Csh Box Unit 1 Prts List Tle 7-12 ivizion Csh Box Unit 1 Prts List Ref No. EDP No. Description Qty Remrk Box (S) Box (L) Box Bse Box Door (S) Box Door (L) Box Cover (S) Box Cover (L) Presser Plte Plte Stopper Indictor Window Indictor Arm (S) Indictor Arm (L) Box Prism (Ner-Full) Box Prism (Stte) Lever Nerly Full (S) Lever Nerly Full (L) Hndle Hndle Cover Key Cover Lock Brcket Lock Plte Box Shft (1) Box Shft (2) Home Position Lever Spring Csh Stock Spring IQ P-Box Spring x6 Phillips, Self Tightening, Binding 3M Screw (Blck) x8 Phillips, Self Tightening, Binding 3M Screw x6 Pn NONSERT Hed Screw x12 Flthed, Phillips, Self Tightening 3M Screw x14 Phillips, Self Tightening, Pn Hed 3M Screw (Blck) M3 x 12 Pn Hed Screw with W Wsher 3M Crescent Snp Ring RFID Tg KF srl Phone Indictor Cover (S) Indictor Cover (L) x5 Rmimte 3M Screw Key Spcer KF srl Phone

105 KF srl Phone Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Csh Box Unit 2 Exploded View Figure 7-13 ivizion Csh Box Unit 2 Exploded View 7-25 KF srl Phone

106 KF srl Phone Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Csh Box Unit 2 Prts List Tle 7-13 ivizion Csh Box Unit 2 Prts List Ref No. EDP No. Description Qty Remrk Frme Inner L Frme Inner R Arm Pusher Arm Slide Lever Arm Center Arm Left Arm Right Home Position Lever Stck Guide Plte Nut Arm Drive Ger Arm Link Ger Feed Drive Pulley Feed Driven Pulley Feed Idol Pulley Link Roller Feed Roller Feed Idol Roller Arm Slide Roller Feed Shft Stck Shft Arm Link Shft Feed Pulley Shft Pin Arm Link Pin Arm Spring Stck Guide Spring Home Position Lever Spring Timing Belt (Eco Specifictions) M2.6 6 Pn Hed Screw with Wsher 3M Phillips, Self Tightening Binding 3M Screw Φ3 E-Ring Φ4 E-Ring Φ2x8 Prllel Pin Sustiner Φ2x14 Prllel Pin Sustiner Φ3x14 Prllel Pin Sustiner Φ3x22 Prllel Pin Sustiner KF srl Phone

107 KF srl Phone Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Csh Box Unit 3 Exploded View Figure 7-14 ivizion Csh Box Unit 3 Exploded View 7-27 KF srl Phone

108 KF srl Phone Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Csh Box Unit 3 Prts List Tle 7-14 ivizion Csh Box Unit 3 Prts List Ref No. EDP No. Description Qty Remrk Unit Cover Frme Outer L Frme Outer R Home Position Prism Bering Bll Guide Spring Bering Connect Frme Bush Stck Ger Stck Idol Ger Feed Ger Drive Ger Connect Ger Shft Idol Ger Bll Spring Feed Roller Spring Connect Ger Shft Bll Guide Spring Poly Acetl Bll 3/8 inch High Level x6 Phillips, Self Tightening, Binding 3M Screw (Blck) x8 Phillips, Self Tightening, Binding 3M Screw Φ2.5 E-Ring Φ2x6 Prllel Pin Sustiner Φ2x8 Prllel Pin Sustiner x10 Phillips, Self Tightening, Binding 3M Screw (Blck) KF srl Phone

109 KF srl Phone Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion LD Version Frme Exploded View Figure 7-15 ivizion LD Version Frme Exploded View 7-29 KF srl Phone

110 KF srl Phone Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion LD Version Frme Prts List Tle 7-15 ivizion LD Version Frme Prts List Ref No. EDP No. Description Qty Remrk LD Roller Arm Assy LD Frme Bse LD Bnknote Front Guide LD Bnknote Rer Guide LD Frme Guide Left LD Frme Guide Right LD Idler Bem LD Roller Arm Bem LD Roller Shft LD One Wy Ger LD Idler Ger Frme Bse Guide Frme Spring Plte Frme Ground Plte OL Roller Bll Bering (F674ZZ) Spring O-Ring M2.6x5 Wsher M2.6x4 Flt Screw Φ2.6x6 Phillips, Self Tightening, Flt Screw Φ3 E-Ring Φ4 E-Ring Φ4 Plin Wsher (Wve Shpe) Φ4x17 Reel Bushing M2.6 Nylon Nut KF srl Phone

111 KF srl Phone Exploded Views & Prts Lists ivizion Series Next-Genertion Bnknote Acceptor Unit Section 7 ivizion Optionl Components Exploded Views Figure 7-16 ivizion Optionl Components Exploded Views 7-31 KF srl Phone

112 Section 7 ivizion Series Next-Genertion Bnknote Acceptor Unit Exploded Views & Prts Lists ivizion Optionl Components Prts List Tle 7-16 ivizion Optionl Components Prts List Ref No. EDP No. Description Qty Remrk OP1 KF srl Phone ivizion Bezel SS Type 1 RoHS 1 Blck/Green LED ivizion Bezel SS Type 2 RoHS ivizion Bezel SS Type 3 RoHS 1 OP Interfce Hrness 1 OP Interfce Hrness 1 Blue/Blue LED (2 Line) Green/Green LED (2 Line) One Side Clipping, Non-USB/IF, JCM Bsic Hrness Connectors nd USB/IF 7-32 KF srl Phone

113 KF srl Phone ivizion Series Next-Genertion Bnknote Acceptor Unit Section 8 8 INDEX Bnknote Jm clering 2-8 Clirtion Methods of 6-6 Tool requirements for 6-6 Cutions high temperture, high humidity or dusty res storge in 1-2 Clening methods of, nd equipment required for 2-8; 2-9 Communictions criteri regrding recipt of 3-1 Contct Informtion Address nd Telephone Numers for 1-14; 3-1 D B C Dimensions entire unit drwing of 1-9 Disssemly/Ressemly instructions for 4-1 E Exploded View illustrtions of 7-1 Fults Tle Listing of A-1 Flowchrt Opertionl 2-15 opertionl 2-15 Instlltion Processes for 2-1 ivizion Unit photo of 1-1 LD 1-2 Nvigtion within mnul procedure for 1-1 F I L N P PC Clirtion Preprtion for 6-7 Performnce Test Requirements for 6-11; 6-15 Performnce Testing instructions for 6-1 Pin Assignments Tle listing primry connector 2-3; 2-4; 2-5; 2-6; 2-7; 2-8 Precutionry Symols types of 1-2 S Sfety pictogrphs indicting 1 to 3 symols inside oxed re 1-1 Specil Notes itlic text highlights finger points to 1-1 Specifictions Electricl informtion regrding 1-6; 1-8 Environmentl informtion regrding 1-5; 1-7 Model Numer Tle of 1-2 Structurl informtion regrding 1-6; 1-8 Technicl informtion regrding 1-5; 1-7 Steps sequentil numering of 1-1 Symols Precutionry definitions of 1-2 System Wiring Digrm Schemtic digrm of 5-1 T Tool Requirements workench 4-1 Trouleshooting Instructions for A-1 W Wiring Digrm system & individul primry prt KF srl Phone

114 KF srl Phone ivizion Series Next-Genertion Bnknote Acceptor Unit INDEX THIS PAGE INTENTIONALLY LEFT BLANK 8-2 KF srl Phone

115 KF srl Phone ivizion Series Next-Genertion Bnknote Acceptor Unit Appendix A A TROUBLESHOOTING This section provides Trouleshooting instructions for the ivizion Series Next-Genertion Bnknote Acceptor Unit. This section contins the following informtion: Introduction Trouleshooting Overview Mlfunction LED Error Codes LED Indiction Conditions. Introduction Most Bnknote Acceptor filures re due to minor cuses. Before replcing ny prts, mke sure tht ll ssemly nd circuit ord connectors re properly fitted nd the hrness is properly connected. Fulty Bnknote cceptnce y the Vlidtor portion of the ivizion is often cused when dust or deris dheres to the Identifiction Sensor, or Trnsport Belt. Clen the Acceptor section first, then oserve the operting stte of the Acceptor in detil when reinitilizing power. This oservtion is importnt in locting ny filure cuses nd the possile fult re. If the Acceptor Hed hs to e repired y disssemling it, lwys re-clirte the Sensors following repir. Perform ll repirs y referring to Clirtion nd Testing in Section 6 of this mnul, nd Disssemly/Ressemly in Section 4 of this mnul. Symptoms Power ON LED Tle A-1 LED Code Condition Sttus LED Trouleshooting Overview The ivizion llows the opertor to perform fult dignosis y checking vrious fult Tle listings ginst the symptom, nd survey the cuse(s) of ny filure occurrences during the process. After determining the cuse of the filure, execute the Performnce Test, perform Sensor re-djustment nd then repir the ivizion Unit y replcing ny pproprite prts deemed necessry. Mlfunction LED Error Codes The ivizion contins two (2) Front Pnel Indictors (e.g., Green Power LED nd Sttus LED tht exhiits four (4) colors). The Power LED lwys lights Green Color when supplying power to the ivizion Unit. The Sttus LED lights solid or flshes one comintion of four (4) Colors when errors, Bnknote jms or reject occurs. The ivizion Sttus, Error Codes, Bnknote Jm Codes or Bnknote Reject Codes re indicted y the numer nd/or Color of the Sttus LED solid or flshing light Color conditions. LED Indiction Conditions Tle A-1 lists the Green Power ON LED nd the vrious Four (4) Color LED Sttus/Error Code indictions for the ivizion Unit. Cuses nd Solutions Norml Condition Extinguished (Out) The ivizion is set-up correctly (Stnd-y). Initilizing Blue Flshes The ivizion is initilizing. Downloding Red Lit Green Lit The ivizion is performing downlod. Ner Full Detection Lit Green Yellow Lit The ivizion hs detected Nerly-full Csh Box Condition. Test Mode Blue Lit The ivizion sttus is in Performnce Test Mode (Stnd-y). Error Red Flshes The ivizion hs n error condition (See Tle A-2 LED Error Codes ). Bnknote Jm Yellow Flshes The ivizion hs jmmed Bnknote (See Tle A-3 Jm LED Flsh Error Codes ). Reject Green Flshes The ivizion hs n error condition (See Tle A-4 LED Reject Codes ). A-1 KF srl Phone

116 KF srl Phone Appendix A ivizion Series Next-Genertion Bnknote Acceptor Unit TrouleShooting The ivizion is not working Green Extinguished (Out) Extinguished (Out) Error, Jm nd Reject Code Tles The Sttus LED indictes vrious color comintions or solid/flsh lighting conditions when errors listed in Tle A-1, Tle A-2 nd Tle A-3 occur. Identify the cuses nd solution for these indictions from ech Tle s list nd ensure tht the reltive ssemles re properly connected nd/or hrnessed, nd tht ll of the Unit s Sensors re clen. Tle A-2 lists the vrious LED Flsh Error Code cuses & solutions. Tle A-2 LED Error Codes LED Color Red Symptoms Flsh Sequence Sttus LED Errors 1 Stcker Full 2 3 Communiction Error etween CPU Bords Sensor Adjustment Error 4 Speed Error 5 E2P Error (no Sensor djustment) 6 Trnsport Error 7 Reject Error 8 9 Power ON LED Stcker Error (Pusher Plte Movement) Pusher Plte Position Error 10 No Csh Box 11 No Acceptor Hed 12 Anti-Strings Error 13 Reserved Reserved Tle A-1 LED Code Condition (Continued) Sttus LED Cuses nd Solutions The power is not eing supplied. [Solution] Ensure the hrnesses re connected to the Interfces. Ensure tht the supply working voltge nd rnge is pproprite. Ensure the Interfce hrnesses re not disconnected etween the Trnsport Unit nd the Frme Unit. Ensure tht the higher Interfce Bord Fuse (F1) is not lown. Ensure tht ll hrnesses nd/or connectors re on the Control CPU Bord. Cuses nd Solutions Detected Stcker Full Condition. [Solution] Retrieving the Bnknotes from the Csh Box. [Reltive Prts] Full Sensor: Vlidtion CPU Bord PL1, PT2, CN2 or Control CPU Bord CN4. Anorml communiction error etween the Control CPU Bord nd the Vlidtion CPU Bord detected. [Solution] Ensure tht ll of the connectors on the Control CPU Bord nd the Vlidtion CPU Bord re properly connected. Anorml Sensor djustment detected on the Control CPU Bord nd the Vlidtion CPU Bord. [Solution] Perform Sensor Adjustment of the Acceptor Unit. Anorml Trnsport Speed Adjustment detected. [Solution] Ensure tht no foreign ojects re dhering to the Sensors. [Reltive Prts] FEED Motor: Interrupter Bord CN1 or Control CPU Bord CN1. Replced the Acceptor Unit without performing Sensor Adjustment. [Solution] Perform Acceptor Unit Sensor Adjustment. Motor locked while trnsporting or stcking Bnknote. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] FEED Motor: Interrupter Bord CN1 or Control CPU Bord CN1. Motor Locked while rejecting Bnknote. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] FEED Motor: Interrupter Bord CN1 or Control CPU Bord CN1. Motor locked while stcking (Pusher Plte movement) Bnknote. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] STACK Motor: Interrupter Bord CN1 or Control CPU Bord CN1. Did not detect the Position Sensor while moving the Pusher Plte. [Solution] Ensure tht the Trnsport Unit nd/or the Csh Box re properly Seted. Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] Home Position Sensor: HP Sensor Bord LED, PT1, C1/High I/F Bord CN5, CN1, CN3 or Control CPU Bord CN3 STACK Motor: Interrupter Bord CN1 or Control CPU Bord CN1. The Csh Box is not seted. [Solution] Ensure tht the Csh Box is properly seted. [Reltive Prts] Box Sensor: Vlidtion CPU Bord PL4, PT3, PT4, CN2 or Control CPU Bord CN4. The Acceptor Unit s Access Cover is not locked in plce. [Solution] Ensure tht the Acceptor Unit s Access Cover is properly locked down. Frud detected. [Solution] Ensure tht no frud condition exists such s nti-stringing. A-2 KF srl Phone

117 KF srl Phone TrouleShooting ivizion Series Next-Genertion Bnknote Acceptor Unit Appendix A Tle A-2 LED Error Codes (Continued) LED Color Red Blue Flsh Sequence 14 Dmged Bord An IC is mlfunctioning. [Solution] The Control CPU Bord or the Vlidtion CPU Bord my e dmged. Replce the Circuit Bords if necessry. 15 ROM/RAM Error ROM or RAM is mlfunctioning. [Solution] The Control CPU Bord or the Vlidtion CPU Bord hs performed normlly. Replce the Circuit Bords if necessry. 1 Reserved Reserved 2 Sttus LED Errors ICB Function (Seting) Error 3 ICB R/W Error 4 ICB Dt Error 5 ICB Numer Error 6 ICB Initilize Error 7 Reserved Reserved 8 Reserved Reserved 9 Reserved Reserved 10 Reserved Reserved 11 Reserved Reserved 12 Reserved Reserved 13 Reserved Reserved 14 Reserved Reserved 15 Reserved Reserved Cuses nd Solutions The ICB Seting cpcity is mlfunctioning. [Solution] The ICB Seting Function or the RF-ID Module my e dmged. Perform seting gin or replce the reltive prts. [Reltive Prts] RFID Module: Vlidtion CPU Bord CN3, CN2 or Control CPU Bord CN4. ICB unle to communicte. [Solution] The ICB Seting Function or the RF-ID Module my e dmged. Perform seting gin or replce the reltive prts. [Reltive Prts] RFID Module: Vlidtion CPU Bord CN3, CN2 or Control CPU Bord CN4. ICB Dt is mlfunctioning. [Solution] The ICB Seting Function or the RF-ID Module my e dmged. Perform seting gin or replce the reltive prts. [Reltive Prts] RFID Module: Vlidtion CPU Bord CN3, CN2 or Control CPU Bord CN4. The Gme Mchine numer is different. [Solution] The ICB Seting Function or the RF-ID Module my e dmged. Perform seting gin or replce the reltive prts. [Reltive Prts] RFID Module: Vlidtion CPU Bord CN3, CN2 or Control CPU Bord CN4. The ICB Seting Function or the RF-ID Module my e dmged. Re-set the Csh Box gin or replce the reltive prts. [Reltive Prts] RFID Module: Vlidtion CPU Bord CN3, CN2 or Control CPU Bord CN4. A-3 KF srl Phone

118 KF srl Phone Appendix A ivizion Series Next-Genertion Bnknote Acceptor Unit TrouleShooting Jm Error Codes Tle A-3 lists the vrious LED Jm Flsh Code cuses & solutions. Tle A-3 Jm LED Flsh Error Codes LED Color Yellow Flsh Sequence Sttus LED Errors Cuses nd Solutions 1 Reserved Reserved 2 Entrnce Sensor Jm A Bnknote jm occurred ner the Entrnce Sensor [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] Entrnce Sensor: Sensor Bord LED1, PT1, CN1, or Vlidtion CPU Bord CN7. Bnknote jm occurs ner the CIS Sensor. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. 3 CIS Sensor Jm [Reltive Prts] CIS Sensor (Upper): Sensor Trnsfer Bord CN4, CN1, CN2, Sensor Bord CN2, CN3, CN1 or Vlidtion CPU Bord CN7. Lower CIS Sensor: Sensor Bord CN5, CN1 or Vlidtion CPU Bord CN7. Bnknote jm occurs ner the Exit Sensor. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the 4 Exit Sensor Jm Trnsport. [Reltive Prts] Exit Sensor: Sensor Bord LED2, PT1, CN1 or Vlidtion CPU Bord CN7. 5 Feed-in Sensor Jm Bnknote jm occurs ner the Feed-in Sensor. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] Feed-in Sensor: High I/F Bord LED1, PT1, CN3/ or Control CPU Bord CN3. 6 Feed-out Sensor Jm Bnknote jm occurred ner the Feed-out Sensor. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. [Reltive Prts] Feed-out Sensor: Vlidtion CPU Bord PL3, PT1, CN2 or Control CPU Bord CN4. 7 Csh Box Inside Jm Bnknote jm occurs t the Csh Box. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport. 8 Reserved Reserved 9 Reserved Reserved 10 Reserved Reserved 11 Reserved Reserved 12 Reserved Reserved 13 Reserved Reserved 14 Reserved Reserved 15 Reserved Reserved A-4 KF srl Phone

119 KF srl Phone TrouleShooting ivizion Series Next-Genertion Bnknote Acceptor Unit Appendix A Reject Error Code Tle A-4 is the LED Reject Error Flsh Codes cuses & solutions. Tle A-4 LED Reject Codes LED Color Flsh Sequence Sttus LED Errors Cuses nd Solutions Lit Green 1 Bnknote Insertion Error 2 UV Sensor Error Bnknote remining Error (Hed Section) Adjustment Error/ Dimeter Error Trnsport Time-Out Error 6 Denomintion Error 7 Photo Pttern Error 1 8 Photo Level Error 9 INHIBIT Error 10 Reject Request 11 Ticket Error 12 Trnsport Overrun Error (Stcker Prt) 13 Bnknote Length Error 14 Photo Pttern Error 2 15 Authentic Bnknote Identify Error Bnknote is rejected y skew detection. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the UV Sensor process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y detecting Bnknote remining in the Acceptor Unit. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the Vlidtion Sensing process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Trnsport timing is incorrect. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the pth ner the Trnsport Pth Sensors. Bnknote is rejected y n incorrect denomintion vlidtion process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the Vlidtion Pttern process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the Trnsmissive Level Vlidtion process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the INHIBIT Setting (nknote cceptnce inhiit). Commnd for Escrow hs not een sent. [Solution] Ensure tht the ctive stte of Host Mchine or n ivizion DIP Switch INHIBIT setting is properly set. Bnknote is rejected y Host Mchine request. [Solution] Ensure the INHIBIT setting of the Host Mchine is correct. Ticket Upside-down. [Solution] Ensure tht the Ticket Brcode is fcing up when inserted. Bnknote is rejected y detecting Bnknote remining in the Trnsport Unit. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Trnsport Unit Sensors. Bnknote is rejected ecuse of length longer thn the cceptle length. [Solution] Ensure tht the Bnknote is proper length Bnknote is rejected y the Vlidtion Pttern process. [Solution] Ensure tht foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform n djustment of the Acceptor Unit Sensors if necessry. Bnknote is rejected y the uthentic Bnknote Vlidtion process. [Solution] Ensure foreign oject nd/or Bnknote is not dhering to the Acceptor Unit Sensors. Perform djustment of the Acceptor Unit Sensors if necessry. A-5 KF srl Phone

120 KF srl Phone Appendix A ivizion Series Next-Genertion Bnknote Acceptor Unit TrouleShooting Mintennce Equipment This portion provides product informtion for the ivizion Mintennce Equipment. ivizion Mintennce Equipment c d e NOTE: Only the Europen Connector Version is shown here. Order the JAC No. for the USA Style AC Wll Plug. NOTE: Only the Europen Style Version is shown here. Order the JAC No. for the USA Style AC Wll Plug. f Figure A-1 Additionl Mintennce Equipment Requirements Tle A-5 Additionl Mintennce Equipment Prts List Ltr. EDP No. * JAC No. Description Qty. Remrk N/A Reference Pper (White: KS-072 Std) G R UAC 1 c G R UAC USB Cle 1 d G00262 N/A UAC/MIB Adptor Hrness (ID-003) 1 e G RA Power Cord 1 For UAC f G R AC Adptor 1 For UAC *. A Product EDP Numer tht egins with G is Product developed y JCM-E Germny.. Crefully replce the used Reference Pper ck into its protective Shipping Crton following ech clirtion use (refer to Reference Pper Use Precutions nd Figure 1-3 in Section 1 for further detiled user instructions. Reference Pper Hndling All JCM Reference Pper should e hndled s follows: 1. Do not llow the Reference Ppers to endure high tempertures nd/or high humidity environments. 2. Store unused Reference Ppers in their originl Shipping Crton to void exposing them to direct Sunlight nd/or right indoor light. Ensure tht the Reference Ppers eing stored re not dmged s they re replced into their shipping crton. 3. Do not use Reference Pper contining dmged res tht re worn, dirty, wrinkled, distorted nd/ or discolored. 4. Use new Reference Pper for every 400 Units eing clirted. Incorrect clirtion errors my occur when using Reference Pper tht hs een used for clirting more thn 400 Units. 1 A-6 KF srl Phone

121 KF srl Phone B GLOSSARY ivizion Series Next-Genertion Bnknote Acceptor Unit Appendix B 1 Acceptor term used in Communiction Section 3 referencing functions sent to, nd received from the Bnknote Acceptor y softwre commnds See Pge 1-1 B A 2 Bezel removle Plstic Assemly ttched to the front of the Bnknote Insertion Slot of ivizion Unit See Pge 1-2 C 3 Clirtion process performed on electronic equipment which ensures tht ll circuits re properly ligned nd operting t optimum levels. For ivizion, clirtion is ccomplished using softwre sed progrm which checks nd sets the opertionl reference levels for Sensors. This helps to ensure tht the Unit opertes with the highest Bnknote cceptnce rte possile. Clirtion is recommended whenever the CPU Bord, or one of the Sensor Bords re replced See Pge cctlk Seril sed Communiction Protocol commonly used in control, electronic pyment, nd vending systems. Developed y Money Controls Ltd., the formt enjoys widespred use throughout Europe. cc-tlk is supported communictions formt in the ivizion Unit See Pge Checksum numericl vlue ssigned to dt file or lock of dt (usully expressed in Hexdeciml nottion). Checksum vlues re used to verify tht the contents of dt file re not corrupted in ny wy during trnsmission or encryption. The Checksum vlues of oth the originl nd duplicte files re compred to ech other. If the vlues mtch, then the duplicte file is recommended tht file e copied or encrypted gin until the Checksum do gree technique, which is highly ccurte nd cn detect dt errors down to single computer See Pge CIS n cronym for Contct Imge Sensor. This type of imge Sensor is le to scn every portion of Bnknotes surfce s it psses over it See Pge 4-6,4-8 & CPU n cronym for Centrl Processing Unit See Pge 4-1 D 8 DIP Switch Block Dul Inline Pckged Switch Block printed circuit ord mountle two-position slide switch pckge contining up to 16 individul switches See Pge 2-2 E 9 Externl DIP Switch procedure for performing ivizion Clirtion using the Externl DIP Switches See Pge 6-15 B-1 KF srl Phone

122 KF srl Phone Appendix B ivizion Series Next-Genertion Bnknote Acceptor Unit F F 10 FFC n cronym for Flt Flexile Cle. This type of Cle contins printed circuit trces in it, nd is generlly used to interconnect nd distriute signl informtion etween vrious Printed Circuit Bords See Pge 4-3, 4-7 & FG PLT n cronym for Frme Grounding PLTe See Pge FPC n cronym for Flexile Printed Circuit. This type of Circuit Crd/Cle contins printed circuit trces on ech side of it, nd is generlly used to interconnect nd distriute signl informtion etween two closely plced Printed Circuit Bords See Pge 4-4 I 13 ID Sticker nother nme for the Product Identifiction Lel locted on the right side of the ivizion Cinet Frme See Pge 6-7 J 14 JCM USB Tool Suite Stndrd Edition PC Appliction Progrm tht includes Su- routine Progrms for Downloding File, Clirting Sensors, exmining Performnce Metrics, testing Acceptor Functions, Enling & Disling the ICB Feture nd viewing n imge of the lst Bnknote ccepted See Pge JPL n cronym for JCM Privte Line to identify the Connector for ctivting n ttched Sentry-2 Bezel Option See Pge 1-4 L 16 LD n cronym for Less Down or No Stcker present See Pge LED n cronym for Light Emitting Diode. An LED is Semiconductor Device which turned on, emits signl output in the visile light rnge. Aville in vriety of colors, LEDs re cost effective nd re commonly used s Indictor Lights in vriety of equipment devices. LEDs re lso ville in the invisile light rnge (i.e., ultrviolet, ner-infrred etc.) mking then useful s opertionl indictors for vriety of electronic equipment nd pplictions, such s Bnknote Vlidtion Circuit in the ivizion Unit See Pge 1-5 P 18 Photo-Coupler method of incresing sfety to oth the equipment nd personnel y isolting nd routing trnsmitted dt signls vi using Light Emitting Diode (LED) nd Photosensitive Trnsistor comintion circuit in vrious electronic equipment See Pge Pictogrph smll interntionlly recognized sfety nd ttention symols plced to the left Notes, Cutions nd Wrnings throughout JCM Mintennce Mnul See Pge 1-1 R 20 Reference Pper specilly coted/colored pper strips which re inserted into Bnknote Vlidtor when performing ivizion Unit Clirtion. Reference Pper is used to help set minimum nd mximum threshold detection levels when djusting the photo-opticl Sensors in the unit for optimum B-2 KF srl Phone

123 KF srl Phone Appendix B ivizion Series Next-Genertion Bnknote Acceptor Unit S performnce See Pge RFID n cronym for Rdio Frequency IDentifiction See Pge 1-2 & RS232C common seril dt communiction stndrd protocol See Pge 2-5 S 23 Sensor Photo Sensitive Device nd LED comintion designed to detect timing nd movement events See Pge 1-2 T 24 Timing Belt Ruerized Belts used to trnsport Bnknote inside the Acceptor See Pge 4-1 V 25 Vlidtion in Bnknote Vlidtors, identifies the process of drwing Bnknote into the Unit nd then uses vrious Sensors to red nd determine the uthenticity of the Bnknote sed on the comprison of collected reding to set of reference dt stored in memory See Pge 1-3 B-3 KF srl Phone

124 KF srl Phone ivizion Series Next-Genertion Bnknote Acceptor Unit Issue #4074-SME KF srl Phone