PT100 SCANNER. EPLC9600-CHANNEL8 96 x 96 DIN 1/4. 8 Channel PT-100 Scanner

Transcription

1 PT SCANNER EPLC96CHANNEL8 96x96 /4 DIN EPLC96CHANNEL8 96 x 96 DIN /4 8 Channel PT Scanner 8 x 64 Graphcal LCD dsplay 8 PT temperature sensor nputs ONOFF control Relay or (pnp source ) transstor output Sensor error detecton Adjustable temperature offset 3 Dfferent alarm and prealarm types for each channel (Hgh, Low and Band Alarms) User defned channel labels Dsplay scan modes Operatng wth Real Tme Clock (RTC) ModBus RTU communcaton protocol (RS3, RS485 and Ethernet communcaton) Data Loggng to USB Flash Memory Adjustable data loggng tme nterval Password protecton for programmng mode Introducton Manual. ENG EPLC96 CHANNEL8 V4 7/3

2 ABOUT INSTRUCTION MANUAL Instructon manual of EPLC96CHANNEL8 conssts of two man sectons. Explanaton of these sectons are below. Also, there are other sectons whch nclude order nformaton and techncal specfcatons of the devce. All ttles and page numbers n nstructon manual are n CONTENTS secton. User can reach to any ttle wth secton number. Installaton: In ths secton, physcal dmensons of the devce, panel mountng, electrcal wrng, physcal and electrcal nstallaton of the devce to the system are explaned. Operaton and Parameters: In ths secton user nterface of the devce, accessng to the parameters, descrpton of the parameters are explaned. Also n these sectons, there are warnngs to prevent serous njury whle dong the physcal and electrcal mountng or usng the devce. Explanaton of the symbols whch are used n these sectons are gven below. c a Ths symbol s used for safety warnngs. User must pay attenton to these warnngs. Ths symbol s used to determne the dangerous stuatons as a result of an electrc shock. User must pay attenton to these warnngs defntely. Ths symbol s used to determne the mportant notes about functons and usage of the devce.

3 CONTENTS.PREFACE... Page. GENERAL SPECIFICATIONS. ORDERING INFORMATION.3 WARRANTY.4 MAINTENANCE 5.INSTALLATION... Page. GENERAL DESCRIPTION. FRONT VIEW AND DIMENSIONS OF EPLC96CHANNEL8.3 PANEL CUTOUT.4 ENVIRONMENTAL RATINGS.5 PANEL MOUNTING.6 INSTALLATION FIXING CLAMP.7 REMOVING FROM THE PANEL 7 3.ELECTRICAL WIRING... Page 3. TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS 3. ELECTRICAL WIRING DIAGRAM 3.. DEVICE WITH RELAY OUTPUTS 3.. DEVICE WITH TRANSISTOR OUTPUTS 3.3 SUPPLY VOLTAGE INPUT CONNECTION OF THE DEVICE 3.4 SUPPLY VOLTAGE INPUT CONNECTION OF TRANSISTOR OUTPUTS 3.5. GALVANIC ISOLATION TEST VALUE OF EPLC96CHANNEL8 WITH RELAY OUTPUTS 3.6. GALVANIC ISOLATION TEST VALUE OF EPLC96CHANNEL8 WITH TRANSISTOR OUTPUTS 4. CABLE CONNECTION BETWEEN RS3 TERMINAL OF THE DEVICE AND PC... Page 9 5. CONNECTION FOR RS485 SERIAL COMMUNICATION... Page 6. DEFINETION OF THE FRONT PANEL AND ACCESSING TO THE PARAMETERS... Page 6. DEFINETION OF FRONT PANEL 6. MAIN OPERATION SCREEN DEFINETION 6.3 ACCESSING TO THE OPERATOR PARAMETER PAGES 6.4 ACCESSING TO THE TECHNICIAN PARAMETER PAGES 6.5 OPERATOR PAGES PARAMETERS DEFINETIONS 6.6 TECHNICIAN PAGES PARAMETERS DEFINETIONS 6.6. PAGE PARAMETERS 6.6. PAGE PARAMETERS PAGE3 AND PAGE4 PARAMETERS RS3 SETUP PAGES PARAMETERS RS485 SETUP PAGES PARAMETERS USB SETUP PAGES PARAMETERS ETHERNET SETUP PAGES PARAMETERS REAL TIME (RTC) SETUP PAGES PARAMETERS 7.OPERATION GRAPHICS OF ALARM AND PREALARM TYPE... Page 39 8.MODBUS ADDRESS... Page 8. OUTPUT ADDRESSES 8. PROCESS VALUES ADDRESSES 4 9.SPECIFICATIONS...Page 4.OTHER INFORMATIONS... Page 4 3

4 EU DECLARATION OF CONFORMITY Manufacturer s Name : EMKO ELEKTRONIK A.S. Manufacturer s Address : DOSAB, Karanfl Sk., No:6, 6369 Bursa, TURKEY The manufacturer hereby declares that the product: Product Name : CHANNEL8 (8 Channel PT Scanner) Type Number : EPLC96 Product Category : Electrcal equpment for measurement, control and laboratory use Conforms to the followng drectves : 6 / 95 / EC The Low Voltage Drectve 4 / 8 / EC The Electromagnetc Compatblty Drectve has been desgned and manufactured to the followng specfcatons: EN 664:7 EMC Generc Emsson Standard for Industral Envronments EN 66:5 EMC Generc Immunty Standard for Industral Envronments EN 6: Safety Requrements for electrcal equpment for measurement, control and laboratory use When and Where Issued nd Authorzed Sgnature June Name : Serpl YAKIN BursaTURKEY Poston : Qualty Manager 4

5 .Preface EPLC96CHANNEL8 seres 8 channel PT scanner devces are desgned for measurng and loggng temperature. They can be used n many applcatons wth ther PT process nput, alarm outputs, selectable alarm functons, RS3 / RS485 / Ethernet / USB communcatons. Applcaton Felds Glass Plastc PetroChemstry Textle Automatve Machne producton ndustres etc... Applcatons Heatng Bakng Ovens Incubators Storages Ar Condtonng etc... General Specfcatons EPLC96 CHANNEL8 Power Supply Input Standard Unversal Supply Input 4 V V, 5/6Hz Optonal Supply Input 4V V 5/6Hz, 4V Z Process Inputs PT(wre) Standard Relay Outputs Alarm Outputs Temperature Alarm Out Optonal Transstor Outputs Alarm Outputs Standard Communcaton RS3 Modbus RTU Protocol Optonal Communcaton RS485 Optonal Communcaton ETHERNET Modbus RTU Over TCP Modbus RTU TCP/IP Protocol USB Temperature Data Loggng Optonal Communcaton 5

6 . Orderng Informaton EPLC96CHANNEL8 A ( 96 x 96 /4 DIN). B. C D E A Supply Voltage...4V V ( %5;+%) 5/6Hz 4VZ(%5;+%) 4VV(%5;+%) 5/6Hz 9 Customer B Outputs Relay outputs wth common R for each NO contact 5A max. (5A@5V at resstve load) for each Common contact 5A max (5A@5V at resstve load) pnp source Transstor outputs T Output current A Max. for each transstor output. C Standard Seral Communcaton RS3 (up to 5 baudrate, No solaton ) All order nformaton of EPLC96CHANNEL8 are gven on the table at left. User may form approprate devce confguraton from nformaton and codes that at the table and convert t to the orderng codes. Frstly, supply voltage then other spesfcatons must be deteermned. Please fll the order code blanks accordng to your needs. Please contact us, f your needs are out of the standards. D Optonal Communcaton None 4 RS485 (up to 5 baudrate, 5VAC solaton ) E ETHERNET (Mbt/s, 5VAC solaton ) E Optonal Communcaton None U USB (USB. for temperature data loggng ).3 Warranty EMKO Elektronk warrants that the equpment delvered s free from defects n materal and workmanshp. Ths warranty s provded for a perod of two years. The warranty perod starts from the delvery date. Ths warranty s n force f duty and responsbltes whch are determned n warranty document and nstructon manual performs by the customer completely..4 Mantenance Repars should only be performed by traned and specalzed personnel. Cut power to the devce before accessng nternal parts. Do not clean the case wth hydrocarbonbased solvents (Petrol, Trchlorethylene etc.). Use of these solvents can reduce the mechancal relablty of the devce. Use a cloth dampened n ethyl alcohol or water to clean the external plastc case. 6

7 .Installaton c Before begnnng nstallaton of ths product, please read the nstructon manual and warnngs below carefully. In package, One pece unt Two peces mountng clamps One pece nstructon manual A vsual nspecton of ths product for possble damage occured durng shpment s recommended before nstallaton. It s your responsblty to ensure that qualfed mechancal and electrcal techncans nstall ths product. If there s danger of serous accdent resultng from a falure or defect n ths unt, power off the system and separate the electrcal connecton of the devce from the system. The unt s normally suppled wthout a power supply swtch or a fuse. Use power swtch and fuse as requred. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. Never attempt to dsassemble, modfy or repar ths unt. Tamperng wth the unt may results n malfuncton, electrc shock or fre. Do not use the unt n combustble or explosve gaseous atmospheres. Durng the equpment s putted n hole on the metal panel whle mechancal nstallaton some metal burrs can cause njury on hands, you must be careful. Montage of the product on a system must be done wth t s fxng clamps. Do not do the montage of the devce wth napproprate fxng clamp. Be sure that devce wll not fall whle dong the montage. It s your responsblty f ths equpment s used n a manner not specfed n ths nstructon manual. 7

8 . General Descrpton Mountng Clamp Panel surface (maxmum thckness 5 mm /.59 nch) Front Panel IP65 protecton NEMA 4X. Front Vew and Dmensons of EPLC96CHANNEL /. a/a Sym ü 96 mm / 3.78 nch Maxmum 5 mm /.59 nch 96 mm / 3.78 nch ± mm /.47 nch 84 mm / 3.3 nch 8

9 .3 Panel Cutout 9mm / 3.6 nch 9 mm / 5.8 nch (mn) 9 mm / 5.8 nch (mn) 9mm / 3.6 nch 9

10 .4 Envronmental Ratngs Operatng Condtons Operatng Temperature : to 5 C Max. Operatng Humdty : 9% Rh (noncondensng) Alttude c : Up to m. Forbdden Condtons: Corrosve atmosphere Explosve atmosphere Home applcatons (The unt s only for ndustral applcatons).5 Panel Mountng Before mountng the devce n your panel, make sure that the cutout s of the rght sze. Check front panel gasket poston 3Insert the devce through the cutout. If the mountng clamps are on the unt, put out them before nsertng the unt to the panel. 3 c Durng nstallaton nto a metal panel, care should be taken to avod njury from metal burrs whch mght be present. The equpment can loosen from vbraton and become dslodged f nstallaton parts are not properly tghtened. These precautons for the safety of the person who does the panel mountng.

11 .6 Installaton Fxng Clamp The unt s desgned for panel mountng. Insert the unt n the panel cutout from the front sde. Insert the mountng clamps to the holes that located top and bottom sdes of devce and screw up the fxng screws untl the unt completely mmoble wthn the panel c Montage of the unt to a system must be done wth t s own fxng clamps. Do not do the montage of the devce wth napproprate fxng clamps. Be sure that devce wll not fall whle dong the montage..7 Removng from the Panel c Before startng to remove the unt from panel, power off the unt and the related system. Loosen the screws. Pull mountng clamps from top and bottom fxng sockets. 3Pull the unt through the front sde of the panel 3

12 3.Electrcal Wrngs c c c c You must ensure that the devce s correctly confgured for your applcaton. Incorrect confguraton could result n damage to the process beng controlled, and/or personal njury. It s your responsblty, as the nstaller, to ensure that the confguraton s correct. Devce parameters has factory default values. These parameters must be set accordng to the system s needs. Only qualfed personnel and techncans should work on ths equpment. Ths equpment contans nternal crcuts wth voltage dangerous to human lfe. There s severe danger for human lfe n the case of unauthorzed nterventon. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. 3. Termnal Layout and Connecton Instructons Termnal layout for ethernet communcaton Termnal layout for RS485 communcaton USB. RS 3 COMMUNICATION RS 3 COMMUNICATION DD+ a RS 485 COMMUNICATION ETHERNET COMMUNICATION a USB. a a Max..5mm /.98 nch Wre Sze: 8AWG/mm² Sold /Stranded Torque,5Nm Screw drver,8 x3mm

13 3. Electrcal Wrng Dagram 3.. Devce wth Relay Outputs c Electrcal wrng of the devce must be the same as Electrcal Wrng Dagram below to prevent damage to the process beng controlled and personnel njury. Power Supply Input...4V V ( %5;+%) 5/6Hz 7VA 4VV(%5;+%) 5/6Hz 7VA 4VZ(%5;+%) 7W (It must be determned n order.) Process Inputs (PT) PT PT PT PT PT PT PT 3 8 N () 9 L (+) GENERAL PRE ALR. OUTPUT CH = CHANNEL GENERAL ALR. OUTPUT CH5 ALARM OUTPUT 9 Relay Outputs (Alarm Outputs for Channels to 5) CH8 ALARM OUTPUT CH4 ALARM OUTPUT 8 Common CH7 ALARM OUTPUT CH3 ALARM OUTPUT 7 COMMON CH ALARM OUTPUT x 5A@5VV CH ALARM OUTPUT COMMON 5 x 5A@5VV CH6 ALARM OUTPUT USB. COMMUNICATION RS 3 COMMUNICATION ETHERNET OR RS485 COMMUNICATION PT AGND CH8 CH7 CH6 CH5 CH4 CH3 CH CH Common Relay Outputs (Alarm Outputs for Channels 6 to 8, General Alarm Output and General PreAlarm Output ) RS485, Ethernet and USB communcatons are optonal 3

14 3.. Devce wth Transstor Outputs c Electrcal wrng of the devce must be the same as Electrcal Wrng Dagram below to prevent damage to the process beng controlled and personnel njury. Power Supply Input...4V V ( %5;+%) 5/6Hz 7VA 4VV(%5;+%) 5/6Hz 7VA 4VZ(%5;+%) 7W (It must be determned n order.) Process Inputs (PT) PT PT PT PT PT PT PT N () 8 9 L (+) CH ALARM OUTPUT CH ALARM OUTPUT CH3 ALARM OUTPUT CH4 ALARM OUTPUT CH5 ALARM OUTPUT CH6 ALARM OUTPUT CH7 ALARM OUTPUT CH8 ALARM OUTPUT GENERAL ALR. OUTPUT GENERAL PRE ALR. OUTPUT USB. COMMUNICATION RS 3 COMMUNICATION ETHERNET OR RS485 COMMUNICATION PT AGND CH8 CH7 CH6 CH5 CH4 CH3 CH CH x A@4VZ 6 POWER SUPPLY 4VZ ±%5 Transstor Outputs (Alarm Outputs for Channels to 8, General Alarm Output and General PreAlarm Output ) CH = CHANNEL RS485, Ethernet and USB communcatons are optonal 4

15 Y Note 3.3 Supply Voltage Input Connecton of the Devce al N 4 5 Note3 Note External Fuse ( A T) c Power Supply Swtch Power Supply 4V V ( %5;+%) 5/6Hz 7VA or, 4VV(%5;+%) 5/6Hz 7VA or, 4VZ(%5;+%) 7W Note :There s an nternal 33R W fusble flameproof resstor n 4 V V 5/6Hz There s an nternal 4R7 W fusble flameproof resstor n 4VW 5/6Hz Note: L s (+), N s () for 4V Z Supply Voltage Note3: External Fuse s recommended c c Make sure that the power supply voltage s same ndcated on the nstrument. Swtch on the power supply only after that all the electrcal connecton have been completed. Supply voltage range must be determned n order. Whle nstallng the unt, supply voltage range must be controlled and approprate supply voltage must be appled to the unt. Controllng prevents damages n unt and system and possble accdents as a result of ncorrect supply voltage. There s no power supply swtch or fuse on the devce. So a power supply swtch and a fuse must be added to the supply voltage nput. Power supply swtch and fuse must be put to a place where user can reach easly. Power supply swtch must be two poled for seperatng phase and neutral. On/Off condton of power supply swtch s very mportant n electrcal connecton. On/Off condton of power supply swtch must be sgned for preventng the wrong connecton. External fuse must be on phase connecton n Vsupply nput. External fuse must be on (+) lne connecton n Zsupply nput. c The nstrument s protected wth an nternal fuse (Please refer to Note for nformaton). In case of falure t s suggested to return the nstrument to the manufacturer for repar. 5

16 3.4 Supply Voltage Input Connecton of the Transstor Outputs Ths power supply connecton s need only when transstor type outputs are used. a (+) Note c 3 Note () 9 Power Supply Swtch Supply Voltage 4V Z (±5%) Note : External fuse s recommended. Note : Fuse value must be select accordng to the system. c c Make sure that the power supply voltage s the same ndcated on the nstrument. Swtch on the power supply only after that all the electrcal connectons have been completed. Whle nstallng the unt, supply voltage range must be controlled and approprate supply voltage must be appled to the unt. Controllng prevents damages n unt and system and possble accdents as a result of ncorrect supply voltage. There s no power supply swtch on the devce. So a power supply swtch must be added to the supply voltage nput. In accordance wth the safety regulatons, the power supply swtch shall brng the dentfcaton of the relevant nstrument.power supply swtch shall be easly accessble by the user. Power swtch must be two poled for seperatng phase and neutral. On/Off condton of power swtch s very mportant n electrcal connecton. On/Off condton of power swtch must be sgned for preventng the wrong connecton. If an external fuse s used, t must be on (+) lne connecton n Zsupply nput. 6

17 3.5 Galvanc Isolaton Test Values of EPLC96CHANNEL8 wth Relay Outputs Supply Input of Devce 4 5 V V Analog nputs V V Relay Outputs V V RS 3 V V RS 485 V V Usb V V Ethernet 7

18 3.6 Galvanc Isolaton Test Values of EPLC96CHANNEL8 wth Transstor Outputs V V Supply Input of Devce Supply Input of Output Card V V V V Analog nputs V V Transstor Outputs 5V V V V RS 3 5V V V V RS 485 5V V V V Usb V V 5V V Ethernet 8

19 4. Cable Connecton Between RS3 Termnal of the Devce and PC PC (Personal Computer) 9 Pn DCON connecton NA RX TX 8 TX RX 7 6 GND GND NA NA Cable Lenght must be max. meters for 96 baud rate 9

20 5. Connecton for RS485 Seral Communcaton PC(Personal Computer) RS3 Ş RS485 Convertor MASTER RS3 Connecton Cable D SLAVE D Rt 3 termnal can be connected n RS485 lne D DD+ D+ Rt resstor = W For communcaton connecton Twsted Par cable must be used Cable lenght can be maxmum meters n 96 baud rate SLAVE When baud rate ncreases, cable lenght must be decreased. D DD+ D SLAVEN D DD+ D+ Rt

21 6. Defneton of the Front Panel and Accessng to the Parameters 6.. Defnton of Front Panel 8 x 64 Pxel Graphcal LCD Standard Functon Buttons Channel Selecton Buttons Programmng Mode Access Button ü ENTER BUTTON Ths button s used to confrm the varable value n varable value changng screen. ESCAPE BUTTON Ths button s used to ext from varable value changng screen to precedng vsualzaton screen wthout savng varable value, and return to man operaton screen. DELETE BUTTON Ths button s used to delete the last dgt of the value n varable value changng screen. a/a +/. Sym CHANGE CASE BUTTON Ths button s used to changng the character between uppercase and lowercase, whch cursor s show for strng varable n varable value changng screen. SIGN & SYMBOL BUTTON Ths button s used to changng the sgn value for sgn type varables, enterng the dot for real type and enterng the symbol character for strng type varables n varable value changng screen. DOWN BUTTON Ths button s used to decrement the dgt, whch cursor s show of varable n varable value changng screen and used to accessng next programmng page n programmng mode. UP BUTTON Ths button s used to ncrement the dgt, whch cursor s show of varable n varable value changng screen and used to accessng prevous programmng page n programmng mode. RIGHT BUTTON Ths button s used to move cursor to the rght sde for one dgt n varable value changng screen and selectng the varable for changng n programmng mode. LEFT BUTTON Ths button s used to move cursor to the left sde for one dgt n varable value changng screen and selectng the varable for changng n programmng mode. PROGRAMMING MODE ACCESSING BUTTON Ths button s used to accessng to programmng mode parameters pages.

22 6.. Man Operaton Screens Defneton If the dsplay type parameter value DSP.TYPE = Process Value Analog Channels Names PreAlarm Status Alarm Status Analog Channels Numbers Alarm Messages MAIN OPERATION SCREEN Press rght button for accessng the man operaton screen MAIN OPERATION SCREEN Press left button for accessng the man operaton screen If more than one alarm messages s present, each alarm message s showng on LCD screen durng second. If the dsplay scan parameter value DSP.SCAN =, each man operaton screen s showng on LCD screen durng tme defned by SCAN TIME parameter value.

23 If the dsplay type parameter value DSP.TYPE = Analog Channels Numbers Analog Channels Names Process Value Set Value Alarm Messages MAIN OPERATION ( CHANNEL SCREEN) Press number (,,3,4,5,6,7 or 8) buttons for accessng the relevant channel screen. MAIN OPERATION ( CHANNEL4 SCREEN) If more than one alarm messages s present, each alarm message s showng on LCD screen durng second. If the dsplay scan parameter value DSP.SCAN =, each man operaton screen s showng on LCD screen durng tme defned by SCAN TIME parameter value. 3

24 6.3. Accessng to the Operator Parameter Pages OPERATOR PARAMETERS SECTION PASSWORD SCREEN MAIN OPERATION SCREEN When programmng mode access button s pressed and released before 5 seconds s expre, If operator password s dfferent from, operator parameter secton password screen wll be observed, If operator password s then operator parameter screen wll be observed. OPERATOR PARAMETERS SECTION PASSWORD SCREEN Press rght or left button for selectng the password parameter. OPERATOR PARAMETERS SECTION PASSWORD ENTERING SCREEN Mnmum Maxmum 9999 ü Press enter button for accessng to password enterng screen. Enter the operator parameter secton password wth cursor (lef, rght, up and down) buttons. OPERATOR PARAMETERS SECTION PASSWORD ENTERING SCREEN Mnmum Maxmum 9999 OPERATOR PARAMETER SCREEN (CHANNEL PARAMETERS) 34.. ü Press enter button for accessng to the operator secton parameters. Press rght or left button for selectng the parameter. If no operaton s performed for seconds n operator parameters secton, devce turns to man operaton screen automatcally. 4

25 OPERATOR PARAMETER SCREEN (CHANNEL PARAMETERS) PARAMETER ENTERING SCREEN. oc Mnmum Maxmum ü Press enter button for accessng to parameter enterng screen. Change the parameter value wth cursor (lef, rght, up and down) buttons. OPERATOR PARAMETER SCREEN (CHANNEL PARAMETERS) PARAMETER ENTERING SCREEN Mnmum Maxmum ü Press enter button for return parameter screen wth savng parameter value, press escape button for return parameter screen wthout savng parameter value. Press number (,,3,4,5,6,7 or 8) buttons for accessng the relevant channel s parameter screen. OPERATOR PARAMETER SCREEN (CHANNEL7 PARAMETERS).. Other operator secton parameters can be accessed wth same method explaned above, press escape button for return to man operaton screen. If no operaton s performed for seconds n operator parameters secton, devce turns to man operaton screen automatcally. 5

26 6.4. Accessng to the Techncan Parameter Pages TECHNICIAN PARAMETERS SECTION PASSWORD SCREEN MAIN OPERATION SCREEN When programmng mode access button s pressed for 5 seconds, If techncan password s dfferent from, techncan parameter secton password screen wll be observed, If techncan password s then techncan parameter screen wll be observed. TECHNICIAN PARAMETERS SECTION PASSWORD SCREEN Press rght or left button for selectng the password parameter. TECHNICIAN PARAMETERS SECTION PASSWORD ENTERING SCREEN Mnmum Maxmum 9999 ü Press enter button for accessng to password enterng screen. TECHNICIAN PARAMETERS SECTION PASSWORD ENTERING SCREEN Mnmum Maxmum 9999 Enter the techncan parameter secton password wth cursor (lef, rght, up and down) buttons. TECHNICIAN PARAMETER SCREEN (PAGE CHANNEL PARAMETERS ) 5678 ü Press enter button for accessng to the techncan secton parameters. Press number (,,3,4,5,6,7 or 8) buttons for accessng the relevant channel s parameter screen.press down button for accessng to next parameter page. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 6

27 TECHNICIAN PARAMETER SCREEN (PAGE ) TECHNICIAN PARAMETER SCREEN (PAGE 3) Press down button for accessng next parameter page, press up button for accessng prevous parameter page. Press down button for accessng next parameter page, press up button for accessng prevous parameter page. TECHNICIAN PARAMETER SCREEN (PAGE 4) TECHNICIAN PARAMETER SCREEN (PAGE 5 RS 3 PAGE ) Press down button for accessng next parameter page, press up button for accessng prevous parameter page. Press down button for accessng next parameter page, press up button for accessng prevous parameter page. TECHNICIAN PARAMETER SCREEN (PAGE 6 RS 485 PAGE ) TECHNICIAN PARAMETER SCREEN (PAGE 7 USB PAGE ) Press down button for accessng next parameter page, press up button for accessng prevous parameter page. Press down button for accessng next parameter page, press up button for accessng prevous parameter page. If the devce has a optonal RS485 communcaton then RS 485 page s observed, If the devce has a optonal USB communcaton then USB page s observed. Otherwse these pages are not observed. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 7

28 TECHNICIAN PARAMETER SCREEN (PAGE 8 ETHERNET PAGE ) Press down button for accessng next parameter page, press up button for accessng prevous parameter page. TECHNICIAN PARAMETER SCREEN (PAGE 9 RTC PAGE ) Press up button for accessng prevous parameter page, press escape button for return to man operaton screen. If the devce has a optonal ETHERNET communcaton then ETHERNET page s observed, otherwse ths page s not observed. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 8

29 6.5. Operator Pages Parameters Defnetons Analog Channel Number.. Channel Selecton Buttons Parameter ALARM SET PRE. A. SET DSP. BACKLIGHT CONTRAST Explanaton Alarm Set Value For ChannelX PreAlarm Set Value For ChannelX Dsplay Backlght Mode Dsplay Contrast Value Unt O C O C Mn.. 3 Max Default ALARM SET Alarm set value for selected channel s can be adjusted accordng to ths parameter. PRE. A.SET Pre Alarm set value for selected channel s can be adjusted accordng to ths parameter. DSP LIGHT Dsplay backlght s can be controlled by ths parameter value. If parameter value; = LCD backlght s contnuously OFF = LCD backlght s contnuously ON = power safe mode If any button s not pressed durng 3 secs. LCD backlght s automatcally changed OFF mode, when any button s pressed LCD backlght s changed ON mode agan. CONTRAST Dsplay contrast value s can be controlled by ths parameter value. REV. NUM Software Revson Number Devce software revson number s can be seen by ths parameter. Ths parameter s can not be changed, t s only observed. Alarm Set Parameters Modbus Addresses Parameter Name CH ALR. SET CH ALR. SET CH3 ALR. SET CH4 ALR. SET CH5 ALR. SET CH6 ALR. SET CH7 ALR. SET CH8 ALR. SET Modbus Address PreAlarm Set Parameters Modbus Addresses Parameter Name CH PALR. SET CH PALR. SET CH3 PALR. SET CH4 PALR. SET CH5 PALR. SET CH6 PALR. SET CH7 PALR. SET CH8 PALR. SET Modbus Address CH = CHANNEL These parameters are dsplayed on LCD screen wth pont, so that the parameters values are tmes than the real values for modbus functon. Channel number s can be seen upper left sde of the dsplay and can be selected by pressng the channel selecton buttons. If no operaton s performed for seconds n operator parameters secton, devce turns to man operaton screen automatcally. 9

30 6.6. Techncan Pages Parameters Defnetons Page Parameters Analog Channel Number Techncan Parameter Page Number Channel Selecton Buttons Parameter ALARM TYPE PRE. A. TYPE HYSTERESIS BAND ALARM SENSOR ALARM PV. OFFSET Explanaton Alarm Type For ChannelX PreAlarm Type For ChannelX Hysteress Value For ChannelX Bandwth Value For ChannelX Sensor Alarm Ena./Ds Selecton For ChannelX Process Offset Value For ChannelX Unt Mn O 4. C O 4. C ENA/DIS O 5. C Max Default.. ALARM TYPE Alarm type for selected channel s can be adjusted accordng to ths parameter. If parameter value, = Low Alarm = Hgh Alarm 3 = Band Alarm s selected. PRE. A. TYPE PreAlarm type for selected channel s can be adjusted accordng to ths parameter. If parameter value, = Low Alarm = Hgh Alarm 3 = Band Alarm s selected. HYSTERESIS Hysteress parameter value for Alarm and PreAlarm s can be adjusted by ths parameter. BAND ALARM Bandwth for Band alarm s can be adjusted by ths parameter value. SENSOR ALARM Sensor break alarm for selected channel s can be dsable or enable by ths parameter. If parameter value, = Sensor break alarm dsable = Sensor break alarm enable PV. OFFSET Process offset value for selected channel s can be adjusted by ths parameter. Channel number s can be seen upper left sde of the dsplay and can be selected by pressng the channel selecton buttons. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 3

31 Alarm Type Selecton Parameters Modbus Addresses Modbus Address Parameter Name CH ALARM TYPE CH ALARM TYPE CH3 ALARM TYPE CH4 ALARM TYPE CH5 ALARM TYPE CH6 ALARM TYPE CH7 ALARM TYPE CH8 ALARM TYPE PreAlarm Type Selecton Parameters Modbus Addresses Modbus Address Parameter Name CH PRE. A. TYPE CH PRE. A. TYPE CH3 PRE. A. TYPE CH4 PRE. A. TYPE CH5 PRE. A. TYPE CH6 PRE. A. TYPE CH7 PRE. A. TYPE CH8 PRE. A. TYPE Hysteress Parameters Modbus Addresses Parameter Name CH HYSTERESIS CH HYSTERESIS CH3 HYSTERESIS CH4 HYSTERESIS CH5 HYSTERESIS CH6 HYSTERESIS CH7 HYSTERESIS CH8 HYSTERESIS Modbus Address Band Alarm Selecton Parameters Modbus Addresses Parameter Name CH BAND ALARM CH BAND ALARM CH3 BAND ALARM CH4 BAND ALARM CH5 BAND ALARM CH6 BAND ALARM CH7 BAND ALARM CH8 BAND ALARM Modbus Address Sensor Alarm Selecton Parameters Modbus Addresses Modbus Address Parameter Name CH SENSOR ALARM CH SENSOR ALARM CH3 SENSOR ALARM CH4 SENSOR ALARM CH5 SENSOR ALARM CH6 SENSOR ALARM CH7 SENSOR ALARM CH8 SENSOR ALARM Process Value Offset Parameters Modbus Addresses Parameter Name CH PV. OFFSET CH PV. OFFSET CH3 PV. OFFSET CH4 PV. OFFSET CH5 PV. OFFSET CH6 PV. OFFSET CH7 PV. OFFSET CH8 PV. OFFSET Modbus Address CH = CHANNEL These parameters are dsplayed on LCD screen wth pont, so that the parameters values are tmes than the real values for modbus functon. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 3

32 6.6.. Page Parameters Parameter TECH. PW. OPR. PW. DSP. TYPE DSP. SCAN SCAN TIME LANGUAGE Explanaton Techncan Secton Password Operaton Secton Password Man Operaton Screen Type Dsplay Scan ON/OFF Dsplay Scan Perod Devce Language Selecton Unt ON/OFF SEC. Mn Max Default Address TECH. PW Password for enterng to the techncan secton s defned wth ths parameter. If t s, techncan secton accessed wthout enterng password. OPR. PW Password for enterng to the operator secton s defned wth ths parameter. If t s, operator secton accessed wthout enterng password. DSP. TYPE Man operaton screen type s adjusted by ths parameter. If parameter value, = Multple channel vew = Sngle channel vew s selected. DSP. SCAN Dsplay channel scanner mode s adjusted by ths parameter. If parameter value, = Dsplay channel scanner mode OFF = Dsplay channel scanner mode ON SCAN TIME Dsplay scan perod s adjusted by ths parameter. All man operaton screen s dsplayed durng tme defned by ths parameter. LANGUAGE Devce Language s selected by ths parameter. If parameter value, = TÜRKÇE = ENGLISH If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 3

33 Page3 and Page4 Parameters Channel Names Channel Enable/Dsable Selecton Channel Numbers Parameter CH NAME CH NAME CH3 NAME CH4 NAME CH5 NAME CH6 NAME CH7 NAME CH8 NAME CH I/O CH I/O CH3 I/O CH4 I/O CH5 I/O CH6 I/O CH7 I/O CH8 I/O Explanton Channel Name Channel Name Channel3 Name Channel4 Name Channel5 Name Channel6 Name Channel7 Name Channel8 Name Channel Enable/Dsable Channel Enable/Dsable Channel3 Enable/Dsable Channel4 Enable/Dsable Channel5 Enable/Dsable Channel6 Enable/Dsable Channel7 Enable/Dsable Channel8 Enable/Dsable Unt Strng Strng Strng Strng Strng Strng Strng Strng Mn Max ENA/DIS ENA/DIS ENA/DIS ENA/DIS ENA/DIS ENA/DIS ENA/DIS ENA/DIS Default SENSOR SENSOR SENSOR3 SENSOR4 SENSOR5 SENSOR6 SENSOR7 SENSOR8 Address I/O Channel Enable/Dsable Selecton Parameter Channel s enabled and dsabled by ths parameter. If channel s selected as a dsabled ths channel s can not be observed n man operaton scren for sngle vew mode, channel alarm s not be controlled and analogue value for ths channel s can not be recordng on USB fle. If parameter value, = Channel s dsable = Channel s enable CHANNEL NAME Channels label defnton All channels have ther own label, s dsplayed n man operaton screen. channel labels s can be adjusted by ths parameter. Channel labels are can be adjusted maxmum characters. CH = CHANNEL If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 33

34 RS3 Setup Pages Parameters Parameter BAUDRATE PARITY STOP BIT ID Explanaton Baudrate For RS3 Communcaton Party For RS3 Communcaton Stop Bt For RS3 Communcaton ID For RS3 Communcaton Unt Mn Max 6 47 Default Address BAUDRATE Modbus communcaton baudrate for RS3 s can be adjusted by ths parameter. If parameter value, = 48 = 96 3 = 9 4 = = = 5 PARITY Modbus communcaton party bt for RS3 s can be adjusted by ths parameter. If parameter value, = No Party = ODD Party = EVEN Party STOP BIT Modbus communcaton stop bt for RS3 s can be adjusted by ths parameter. If parameter value, = Stop bt = Stop bts ID Modbus communcaton devce ID for RS3 s can be adjusted by ths parameter. Ths parameter value s can be adjusted from to 47 (except 85 and 7). If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 34

35 RS485 Setup Pages Parameters Parameter BAUDRATE PARITY STOP BIT ID Explanaton Baudrate For RS485 Communcaton Party For RS485 Communcaton Stop Bt For RS485 Communcaton ID For RS485 Communcaton Unt Mn Max 6 47 Default Address BAUDRATE Modbus communcaton baudrate for RS485 s can be adjusted by ths parameter. If parameter value, = 48 = 96 3 = 9 4 = = = 5 PARITY Modbus communcaton party bt for RS485 s can be adjusted by ths parameter. If parameter value, = No Party = ODD Party = EVEN Party STOP BIT Modbus communcaton stop bt for RS485 s can be adjusted by ths parameter. If parameter value, = Stop bt = Stop bts ID Modbus communcaton devce ID for RS485 s can be adjusted by ths parameter. If the devce has a optonal RS485 communcaton then RS 485 page s observed, Otherwse these page s not observed. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 35

36 USB Setup Page Parameters Parameter FILE NAME LABEL SAVE TIME SAMP. TIME Explanaton USB Fle Name USB Label USB Tme Record ENA/DIS USB Record Tme Interval Unt Strng Strng Sec. Mn Max 36 Address Default CHAN8.txt SAMPLE FILE NAME USB fle name for recordng analogue values s can be adjusted by ths parameter. Fle name can be adjusted maxmum characters. Recordng fle on usb s csv format and all data s seperated each other wth tab. Example fle format s explaned below. LABEL When the analogue values are recorded on USB fle, user can be defned label for ths recordng. Label can be adjusted maxmum characters. Label are recorded at the end of every lnes of fle. SAVE TIME When the analogue values are recorded on USB fle, user can be save the recordng tme on the fle. Recordng tme s recorded at the begnnng of every lnes of fle. = Real tme s not recorded on USB fle = Real tme s recorded on USB fle for every sample SAMPLE TIME Record tme nterval s can be adjusted by ths parameter. Analogue values are recorded on USB fle wth ths tme nterval. If ths parameter value s usb recordng s dsabled. FLASH MEM. PLUGGED USB Flash Memory Stck Detected Test When the usb flash memory stck s plugged to the devce FLASH MEM.PLUGGED led s lght on. Ths parameter s can not be changed, t s used to nform the user whether USB s plugged. USB Recordng Fle Example 637:6:8 637:6:9 637:6: 637:6: 637:6:3 Recordng Tme CH Value CH Value CH3 Value CH4 Value CH5 Value CH6 Value CH7 CH8 Value Value SAMPLE SAMPLE SAMPLE SAMPLE SAMPLE Label CH = CHANNEL If the devce has a optonal USB communcaton then USB page s observed. Otherwse these page s not observed. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 36

37 ETHERNET Setup Page Parameters Parameter DHCP ETH. PORT ETH. IP NO ETH. NETMASK ETH. GATEWAY ETH. TCP/IP SLCT DEVICE MAC ADR. Explanaton DHCP Enable /Dsable ETHERNET Port No Ethernet IP No Ethernet Netmask Ethernet Gateway TCP/IP Select Devce MAC Address (** ) (** ) (** ) (** ) (** ) (** ) (** ) Unt ENA/DIS Mn Max Default Address DHCP DHCP s an automatc confguraton protocol used on IP networks, If DHCP s enable, devce s adjust our ethernet communcaton confguraton parameters (IP, Netmask,Gateway) dynamcaly for your network system. If DHCP s dsable, you must adjust ethernet confguraton parameters (IP, Netmask,Gateway) for your network system. If parameter value, = DHCP DISABLE = DHCP ENABLE ETH.PORT Ethernet port number s can be adjusted by ths parameter. NET MASK Subnet mask for ethernet communcaton s can be adjusted by ths parameter. If DHCP s selected as a enable there s no need to adjust to ths parameter, f DHCP s selected as a dsable then user must adjust ths parameter accordng to the ther own network system. GATEWAY Gateway for ethernet communcaton s can be adjusted by ths parameter. If DHCP s selected as a enable there s no need to adjust to ths parameter, f DHCP s selected as a dsable then user must adjust ths parameter accordng to the ther own network system. IP IP address for ethernet communcaton s can be adjusted by ths parameter. If DHCP s selected as a enable there s no need to adjust to ths parameter, f DHCP s selected as a dsable then user must adjust ths parameter. PORT SET Ethernet port confguraton s settng by ths parameter, After the all parameter adjusted accordng to system needs, ths parameter value s must be adjusted to for ethernet port settng, after ethernet port settng s completed ths parameter value s turn to zero automatcally. TCP/IP SLCT TCP/IP protocol s selected by ths parameter. = Modbus RTU Over TCP/IP = Modbus RTU TCP/IP (** ) These parameters are only read for modbus functon. If the devce has a optonal ETHERNET communcaton then ETHERNET pages s observed. Otherwse these pages are not observed. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 37

38 REAL TIME (RTC ) Setup Page Parameters ü Parameter YEAR MONTH DAY HOUR MINUTE SECOND Explanaton Year Value For RTC Tme Month Value For RTC Tme Day Value For RTC Tme Hour Value For RTC Tme Mnute Value For RTC Tme Second Value For RTC Tme Unt Press and hold on 3 seconds Enter button for settng the RTC tme value. Mn Max Default YEAR Year value for RTC tme s adjusted by ths parameter. MONTH Month value for RTC tme s adjusted by ths parameter. DAY Day value for RTC tme s adjusted by ths parameter. HOUR Hour value for RTC tme s adjusted by ths parameter. MINUTE Mnute value for RTC tme s adjusted by ths parameter. SECOND Second value for RTC tme s adjusted by ths parameter. If no operaton s performed for seconds n techncan parameters secton, devce turns to man operaton screen automatcally. 38

39 7. Operaton Graphcs of Alarm and PreAlarm Types Hgh Alarm Alarm Output ON OFF HYS Process Value SET Low Alarm Alarm Output ON OFF HYS Process Value SET Band Alarm Alarm Output ON OFF HYS HYS Process Value (SET (BAND/)) SET (SET + (BAND/)) SET = Alarm or PreAlarm Set value HYS = Hysteress value for Alarm and PreAlarm output BAND= Bandwdth for Band Alarm. 39

40 8. Modbus Addresses 8.. Output Addresses OUTPUT ADDRESSES CH ALARM OUT Channel Alarm Output Status CH ALARM OUT Channel Alarm Output Status CH3 ALARM OUT Channel3 Alarm Output Status CH4 ALARM OUT Channel4 Alarm Output Status CH5 ALARM OUT Channel5 Alarm Output Status CH6 ALARM OUT Channel6 Alarm Output Status CH7 ALARM OUT Channel7 Alarm Output Status CH8 ALARM OUT Channel8 Alarm Output Status GEN. ALR. OUT General Alarm Output Status GEN.PREALR.OUT General PreAlarm Output Status Unt Mn Max Default Address Note: Outputs status are can be readed wth modbus functon (read cols). Devce s response for modbus functon s always byte data although the modbus functon request less than 9 outputs port. 8.. Process Values Addresses PROCESS VALUES ADDRESSES CH P. VALUE Channel Process Value CH P. VALUE Channel Process Value CH3 P. VALUE Channel3 Process Value CH4 P. VALUE Channel4 Process Value CH5 P. VALUE Channel5 Process Value CH6 P. VALUE Channel6 Process Value CH7 P. VALUE Channel7 Process Value CH8 P. VALUE Channel8 Process Value Unt O C C O C O C O C O C O C O C O Mn Max Default Address Note: Process values are can be readed wth modbus functon4 (read nput regster). Because of the process values are dsplayed on LCD screen wth pont, the readng values from modbus s tmes than the real values. 4

41 9. Specfcatons Devce Type Housng & Mountng : 8 Channel PT Scanner : 96mm x 96mm x 87.5mm /4 DIN 437 plastc housng for panel mountng. Panel cutout s 9 x 9mm. Protecton Class : NEMA 4X (IP65 at front, IP at rear) Weght : Approxmately.4Kg. Envronmental Ratngs : Standard, ndoor at an alttude of less than meters wth none condensng humdty o o o o Storage / Operatng Temperature: C to +7 C / C to +5 C Storage / Operatng Humudty : 9 % max. (None condensng) Installaton : Fxed nstallaton Overvoltage Category : II Polluton Degree : II. offce or workplace, none conductve polluton Operatng Condtons : Contnuous Devce Supply Voltage and Power : 4 V V (%5 / +%) 5/6 Hz. 7VA 4 V V (%5 / +%) 5/6 Hz. 7VA 4 V Z (%5 / +%) 7W Output Card Supply Voltage and Power : 4 VZ(±5%) 5W (for Transstor output type) Analogue Inputs : PT (IEC75) (ITS9) Accuracy : ±,5% of full scale Lne Compensaton : Maxmum W Sensor Break Protecton : Upscale Samplng Tme : 4msecs. Input Ressstance : > MW Dgtal Output : Transstor or relay outputs Transstor Output : PNP(source) type transstor output (Max. A@4VZ) Relay Output : Resstve Load 5A@5VV (Electrcal Lfe :. operaton (Full Load) Standard Communcaton : RS3 Communcaton (For Modbus RTU) Optonal Communcaton : RS485 (For Modbus RTU) 5VV solated Mbts/s Ethernet (For Modbus RTU Over TCP Modbus RTU TCP/IP selectable) 5VV solated USB. (Data loggng over Flash Stck Memory) Dsplay : 8 x 64 pxel graphcal LCD Approvals : GOSTR,. Other Informatons Manufacturer Informaton: Emko Elektronk Sanay ve Tcaret A.Ş. Demrtaş Organze Sanay Bölges Karanfl Sk. No: BURSA/TURKEY Phone : Fax : Repar and Mantenance Servce Informaton: Emko Elektronk Sanay ve Tcaret A.Ş. Demrtaş Organze Sanay Bölges Karanfl Sk. No: BURSA/TURKEY Phone : Fax : Thank you very much for your preference to use Emko Elektronk Your Technology Partner Products. 4