Configuration guide. PlantWatchPRO. supervisor for small-medium installations LEGGI E CONSERVA QUESTE ISTRUZIONI READ AND SAVE THESE INSTRUCTIONS.

Transcription

1 30/06/ /06/ /06/ /06/ :36:16 16:36:16 16:36:16 16:36:16 X X X 30/06/ /06/ /06/ /06/ :36:16 16:36:16 16:36:16 16:36:16 X X 30/06/ :36:16 16:36:16 16:36:16 16:36:16 X X X X PlantWatchPRO supervsor for small-medum nstallatons 30/06/ /06/ /06/2006 Confguraton gude LEGGI E CONSERVA QUESTE ISTRUZIONI READ AND SAVE THESE INSTRUCTIONS I n t e g r a t e d C o n t r o l S o l u t o n s & E n e r g y S a v n g s

2

3 Content 1. presentaton 5 ENG 2. KEY 7 3. start up 8 Confguraton wzard CONFIGURATION 9 Lne confguraton...9 Model management...9 Ste nformaton...10 Users...11 Floatng sucton...11 System pages...11 Network confguraton...12 Support...12 How to confgure a smple lne...16 How to dfferentate a devce (or a group of devces) from the standard How to create a Restore Pont...20 How to use a prevously created Restore Pont. 5. scheduler 23 I/O confguraton...23 Phone book...23 Rule confguraton...23 I/O test...25 Guardan...25 How to set scheduled rules...27 How to confgure the Guardan program...31 How to confgure emal...32 How to create a scheduled rule to download a report from PlantWatchPRO Condtons for correct confguraton 35 3

4 Before performng any operatons, check that the PlantWatchPRO box contans: 1. the two plastc faceplates (top and bottom); 2. techncal documentaton; 3. the devce tself; 4. four screws (already nserted n poston); 5. the termnals (sx, already connected to the board); 6. two resstors (nsde the case)

5 1. presentaton PlantWatchPRO s the new soluton from CAREL for the supervson of small-medum nstallatons. Complete network and alarm confguraton, smple navgaton and an attractve desgn are some of the features that make PlantWatchPRO the cuttng edge product n ts category. A colour LCD touchscreen, and the use of practcal menus, gude the user smply and ntutvely, wthout the use of a PC (however a PC can be connected f necessary), thus provdng a practcal soluton for all those envronments that do not have room for a computer. Other nnovatve features of PlantWatchPRO nclude: possblty to connect and control up to 100 devces; possblty to connect and control CAREL or Modbus devces on RS485 bus; record up to a maxmum of 100 varables; log data for up to one year (wth 15 mn samplng). connecton to CAREL remotepro and remotevalue remote supervson systems; a Guardan program that boosts and mproves system relablty; 3 output relays, for alarm sgnals or actvatng lghts and defrosts; possblty to export data (alarms, events, system and model confguratons and varable reports) usng a USB memory key (the data are downloaded n a format that s compatble wth Mcrosoft Excel and Mcrosoft Word); mport new standard or custom devces; dsplay graphs; proxmty sensor that actvates the dsplay wthout the user needng to open the cover; external buzzer management; complete alarm confguraton; phone book for SMS contacts, fax numbers, e-mal addresses; actve defrost management; possblty for multple users to access the system, wth dfferent prvleges (admnstrator, normal user, user wth prvleges); nstrument sutable for techncal envronments, no movng parts Key: 1 touch screen 2 proxmty sensor 3 alarm lght 4 devce on lght 5 USB port 6 transparent cover 5

6 1. presentaton General dagram of PlantWatchPRO connectons PSTN GSM/GPRS 4 5 LAN Remote - Internet Explorer 7.0 Key and product codes: 1 PlantWatchPRO 2 PostScrpt-enabled USB prnter 3 PSTN analogue modem (verson PWPROM0000 only) 4 USB memory key 5 PC (va LAN) 6 3 relay outputs 7 Installaton: Modbus RTU lne 8 Installaton: CAREL lne 9 GSM/GPRS modem connecton kt(code PWOPMD0000) 10 optonal GSM/GPRS modem (code PLWOPGSM00) requred to be able to use all the SMS functons; usng modems other than the one suppled by CAREL wll not guarantee correct operaton of the applance and techncal servce 6

7 2. KEY ENG note hghlghts an mportant pont; n partcular as regards the practcal use of the varous product functons warnng warns the user of crtcal areas for the use and safety of PlantWatchPRO USB key ndcates that the functon can only be accessed drectly from PlantWatchPRO (not va web) and usng a USB memory key tutoral offers the user some smple confguraton examples of the most common settngs for the supervson of an nstallaton 7

8 Confguraton wzard When PlantWatchPRO s frst started, the followng presentaton screen wll be dsplayed Pressng accesses the page for selectng the LANGUAGE and the TIMEZONE. 3. start up Press the correspondng felds to select the desred tems from the lsts. The selecton s confrmed by movng to the followng screen ( button) As the fnal phase n the program ntalsaton process, the prevous selectons need to be confrmed by pressng the button or gong back (wth the button) and changng the settngs. Warnng: check the settngs carefully before pressng as once confrmed, the other languages and tme zones can no longer be recovered. Now enter the date and tme by selectng the correspondng felds. The date format s yyyy/mm/dd and the tme format s hh/mm. A confrmaton message then notfes the user that the settngs have been saved and, once the system has been rebooted, the PlantWatchPRO man menu wll be accessed. Warnng: the followng default values are used when frst loggng n: USER: Admn PASSWORD empty; once havng logged n, t s recommended to mmedately change the Admn user password and keep t n a safe place: losng ths nformaton may compromse access to the system 8

9 4. CONFIGURATION Lne confguraton Lne 1 and Lne 2 (these are the two lnes that can be confgured for the nstallaton: choose lne 1 and then proceed n the same way for the second lne, f used). Devces To add (or where necessary remove ) devces to/from the nstallaton, choose the type (from those avalable n the PlantWatchPRO archve), then assgn a short custom descrpton and assgn the address (ths must be dfferent for each devce on the same lne, otherwse the program wll dsplay an error message); a group can also be assgned (up to 5 groups are avalable), used to apply specfc rules and enable or dsable the devce accordng to specal needs. Dsablng a devce means that any alarms t generates wll not be managed. Model management Model confguraton Used to confgure the models correspondng to the nstruments, that s: Alarms (prorty and enable/dsable); Log/graph/HACCP/man vew; Descrpton/unt of measure (custom descrpton and unt of measure). Devce customsaton Lst of devces confgured on the lne; ths s used to dsplay the varables and f necessary change the descrpton. Connecton To set the protocol (CAREL-RS485 or Modbus -RS485) and confgure the seral port parameters. Export model To export models. Check that there s free space on the USB memory key. 9

10 4. CONFIGURATION Import model The followng models of devces can be mported: standard models (downloaded from carel.com); models exported from PlantWatchPRO; models created or modfed usng Devce Creator. To mport a standard model (e.g.: newstandardmodel), download the.zp fle from and unzp the fle nto the man drectory of a USB pen drve. At the end of the procedure, make sure that the "\models\standard\newstandardmodel\" path has been created on the USB pen drve. To mport a model exported from PlantWatchPRO (e.g.: IR33) make sure the.xml the fle s placed on the USB pen drve n "\export\stename\models\ir33. xml". (stename s the name of the ste set on the Confguraton -> Ste nformaton page n the PlantWatchPRO that the model was exported from; f the model s exported drectly to the USB pen drve, the path s created automatcally). Remove model To remove a model that s not used by the nstallaton and thus free up part of the PlantWatchPRO memory. Ste nformaton Ths s used to enter the nformaton relatng to the ste where PlantWatchPRO s nstalled, plus some nformaton on techncal servce for support n the event of problems. The text entered n the MAINTENANCE TECH. and TELEPHONE felds wll be dsplayed when pressng the button from the logn screen, so as to ndcate who to contact n the event of need. The PASSWORD IDENT and CONFIRM (password) felds must be completed f a password needs to be set for the connecton to remotevalue. To mport a model created or modfed usng Devce Creator (e.g.: mymodel.xml) make sure the.xml the fle s placed on the USB pen drve n "export\ mydrectory\models\mymodel.xml. (mydrectory can be any name). Important: f the Devce Creator verson s lower than 3.0 the.xml fle must be located n \models\dcreator\mymodel.xml Important: f mportng an exstng model, some of the data wll be overwrtten. Copy model Used to create new models based on an exstng model, then makng the desred changes. Updatng the model used as the bass for others also changes all the models derved usng the copy functon. 10

11 4. CONFIGURATION ENG Users Admnstrator Used to modfy the password for the admnstrator user. Normal user Used to create new users and assgn them dfferent prvleges (ste confguraton/change parameters/ alarm management). System pages Reload confguraton Ths s the functon that makes the changes made to the prevous confguraton effectve. No changes to the system wll be actve unless the button s pressed, whch remans red ( ) as a remnder, whle the system s stll n the prevous confguraton. Only after havng confrmed the changes on the reload page wll the system be updated. Backup/Restore Backup ste confguraton Once an nstallaton has been confgured, the confguraton can be saved and exported and then used to confgure another PlantWatchPRO. Operaton also avalable va web Restore ste confguraton Import the system confguraton from a USB key Remote servce Used to confgure the user for remote servce. For system securty, the remote servce user s normally dsabled and should be only enabled when remote servce s requred.. Floatng sucton Used to confgure and actvate the floatng sucton pressure control functon. Rack 1 (or 2) Informaton For detals on the operatng status and nformaton on the showcases and compressor racks. Confguraton To confgure the compressor racks, set the connected showcases, the man parameters for the floatng sucton pressure control functon algorthm and reset the algorthm calculaton perod for one or more showcases. Restore pont Ths functon creates and loads a complete mage of the system; the functon s used to restore the system n the event of serous errors and/or faults. 11

12 4. CONFIGURATION Update software To update the PlantWatchPRO software, see Chap. Support "13. Use of the USB memory key". Dsplay/Clock Control panel for the date/tme and dsplay settngs. Download servce log Ths page s used to export the nformaton to be sent to the servce centre when problems occur. After havng nserted the USB memory key, select send to start the operaton. Network confguraton Confguraton of the network settngs for the local network (LAN) connecton. By default, the USE DHCP tem s selected, whch allows the system to detect the network settngs automatcally. The network settngs should only be confgured manually by qualfed personnel. 12

13 4 CONFIGURATION ENG Language selecton Support language actvaton, ths functon changes the language dsplayed, settng Englsh as the auxlary language 13

14 8. CONFIGURATION Tree of the Confguraton menu functons Lne confg. Lne 1/2 Devce lst Devce customsaton Connecton Model management Model confguraton Alarms Import standard models Export model Log/graph/HACCP/man vew Descrpton unt of measure Ste nfo Import model Copy model Remove model Users Admnstrator Remote user Normal user Lst of normal users Floatng Sucton Rack 1/2 Informaton Confguraton System pages Reload confguraton. Backup/restore Update software Dsplay/ clock Backup ste confguraton Restore ste confguraton Restore pont Network confguraton Support Download servce log Language selecton 14

15 Devce detal Lst of varables Varable detal Lst of devce models Lst of devce models Lst of devce models Lst of alarms Lst of varables Lst of varables Normal user detals Rack Rack detal Showcases Lst of showcases Showcase detal Rack Showcases Lst of showcases Showcase detal Parameters Reset 15

16 4. CONFIGURATION How to confgure a smple lne Frst of all, the user needs to confgure PlantWatchPRO n relaton to the devces n the specfc nstallaton. From the home page, enter the menu CONFIGURATION LINE CONFIGURATION LINE 1 DEVICES menu. Progressvely add all the devces featured n the nstallaton and connected to lne 1, assgnng a specfc descrpton, an address and f necessary add the devce to a group (up to fve groups are avalable) for applyng one or more rules (see the part of the manual correspondng to the SCHEDULER menu). Each devce on the same lne must have a dfferent address from the others, otherwse, f the same address s assgned twce, an error message wll be dsplayed. After havng entered the devces, go back and press the LINE 1 DEVICE CUSTOMISATION tem. Here the name of each ndvdual devce and each related varable can be customsed. Go back and choose the type of CONNECTION, from the standard protocols proposed, the connecton speed (BAUD RATE), the number of DATA BITS, the PARITY and the number of STOP BITS. Repeat 1, 2 & 3 for LINE 2 (f used). 16

17 4. CONFIGURATION ENG Enterng MODEL MANAGEMENT MODEL CONFIGURATION ALARMS and choosng the devces on the two lnes from the lst one at a tme, the alarms can be enabled or dsabled and the prorty set (the prorty of an alarm wll be ndcated n the lst wth a dfferent colour, dependng on the level). Then return to the prevous menu and enter LOG/GRAPH/HACCP/MAIN VIEW DEVICE DETAIL VARIABLE DETAIL ; a screen wll be dsplayed for selectng: the frequency for recordng the value of the varable, the colour used to draw the curve showng the trend of ths varable on the graph, and f requred nclude the varable n the report and/or on the graph. In the lst of varables logged, the columns have the followng meanngs: Freq: samplng frequency. G: varable dsplayed on the graph. P: varable ncluded n the HACCP report. M: varable ncluded n the man lst of devces n the nstallaton (INSTALLATION menu). The data recordng perod depends on the sample tme, as shown n the table below: Samplng tme Recordng perod 30 s 13 days 1 mn 26 days 3 mn 80 days 5 mn 133 days 15 mn 400 days 17

18 4. CONFIGURATION DESCRIPTION/UNIT OF MEASURE s used to change the name and unt of measure of the varables. Reload the confguraton, usng the button and the dedcated screen. The lne s thus confgured, and from the INSTALLATION menu all the settngs defned thus far can be dsplayed under CONFIGURATION. 18

19 4. CONFIGURATION ENG How to dfferentate a devce (or a group of devces) from the standard An example of how to create another model of devce wth other features startng from the IR33 From the home page, enter the CONFIGURATION MODEL MANAGEMENT COPY MODELS menu, from the ORIGINAL MODEL lst choose the standard model to start from (n the example, IR33 ) and n the feld TARGET MODEL feld enter the name to be gven to the new model (n the example, the new model has been called IR33modfcato ) The model created s now dentcal to the one used as the startng pont. Return to the MODEL MANAGEMENT MODEL CONFIGURATION menu to customse the new devces created, changng the settngs relatng to: ALARMS; LOG/GRAPH/REPORTS; DESCRIPTION/UNIT OF MEASURE. A model can thus be created that s dfferent from the one used as the startng pont, based on specfc needs. After havng created the new model wth dfferent features from the standard IR33, these types of devces can be nstalled, followng the frst steps n the sequence of operatons presented n the TUTORIAL on the confguraton of a smple lne. 19

20 4. CONFIGURATION How to create a Restore Pont Select CONFIGURATION BACKUP/RESTORE SYSTEM PAGES RESTORE POINT Press CONFIRM Once havng confrmed the restore pont creaton screen, the system reboots. Select "USB key" and then CONFIRM 20

21 4. CONFIGURATION ENG On reboot, the creaton of the restore pont s added to the vents A fle s created on the key: F:/.restore/restoreYYYY-MM-DD-hh-mm-ss where F: ndcated the USB drve YYYY year MM month DD day hh hours mm mnutes ss seconds 21

22 4. CONFIGURATION How to use a prevously created Restore Pont When startng the system, PlantWatchPRO checks for any USB keys nserted, n the logcal sequence USB1, USB2,USB3, f a key s detected t checks for a restore pont, and f a restore pont s found the system proposes the followng screen. In the event of problems, such as nsuffcent space on the USB key or read and/or wrte problems durng the procedure, the system wll warn the user wth a error message, awatng confrmaton by the user, after the whch the system wll be rebooted. the user then has 10 seconds to accept the restore pont, after ths tme the system starts normally. If any area of the screen s selected, the restore procedure starts. If the USB key has more than one restore pont, the unwanted restore pont fles should be deleted, so as to make sure that PlantWatchPRO only restores the desred confguraton. Important: once the backup or restore procedure has started, do not touch the screen and do not remove the key untl the operaton has termnated. The operaton may take a number of mnutes. At the end of the operaton, the ntal logn screen s shown. 22

23 5. scheduler I/O confguraton Ths menu s used to confgure the number of attempts at an alarm sgnal (f the prevous was not successful) and the nterval between the one attempt and the next at the followng sgnals: fax; SMS; e-mal; PlantVsorPROremote. As regards the e-mal addresses, the data relatng to the server and the Dal-Up connecton can be smply and ntutvely confgured on PlantWatchPRO. In addton, the procedure and tme for resettng the buzzer and the three relays can also be set. Phone book Up to fve fax recpents, fve SMS numbers, fve e-mal addresses and one remote access connecton can be confgured. Each recpent may have more than one number or address, separated by sem-colons (;),as n the most commonly used e-mal programs What s a rule? For each alarm or group of alarms (ncludng from dfferent devces), a seres of rules can be defned, whch may be: a set of actons (fax, SMS, e-mal, prnt, actvate relay, buzzer, remote access); a tme band; a delay. If an alarm goes off, the actons are performed. If a delay s set, the actons are performed after havng wated the tme set for the delay. If the tme band s set, the actons are only performed f the alarm s actvated wthn the tme band. Rule confguraton Tme bands Used to enter tme bands for mplementng the rules; the DAILY/WEEKLY/SPECIAL EVENT submenu can be used to add or remove tme bands of dfferent duratons that can be completely customsed by the user. 23

24 5. SCHEDULER Actons Notfcatons Confguraton of the parameters for the notfcatons and the actvaton of the alarm channels. Rules Dsplay the lst of rules for notfyng the alarms; rules can be added/removed or edted, pressng the detal of the rule to open the specal menu for settng the confguraton parameters. For correct data entry, frst create the tme bands and the actons. Scheduled actvtes Lst of the scheduled actvtes; the parameters controllng the varous actvtes can be set, where necessary assgnng them to a certan group of devces (set durng the confguraton procedure). Scheduled rules Dsplay the lst of scheduled rules; scheduled rules can be added/removed or edted, pressng the detal of the rule to open the specal menu for settng the confguraton parameters. Sgn of lfe: ths functon can be used to enter a scheduled command that sends a sgn of lfe (notfcaton acton) va one of the channels avalable Reports Used to create and set a new scheduled acton that sends a report by e-mal and/or prnts a hard copy. Data savng Ths functon s used to create a scheduled acton to automatcally save a report to USB memory key. Assocated wth a coherent tme band usng a scheduled rule, the report s downloaded automatcally. 24

25 5. SCHEDULER I/O test Test the correct operaton of the Input/Output channels. Guardan Notfcatons Confguraton of the notfcaton parameters for the Guardan program; the channels set are used by the Guardan to send notfcatons of any malfunctons on PlantWatchPRO to the techncal personnel ndcated. Alarm prorty Used to confgure the prorty of the alarms, enterng the settngs n the respectve felds. If the type of the alarm s selected, the Guardan program checks that the alarm s managed wthn the maxmum tme specfed n the feld. If ths s not the case, notfcaton s sent va the channels confgured n the NOTIFICATIONS menu. 25

26 5. SCHEDULER Tree of the Scheduler menu functons I/O confg. Fax confg. SMS confg. E-mal confg. e-mal Remote confg. Dal-up Network confg. Relay detals Phone book Fax Sms E-mal Remote access servce Daly Daly detals Rle confg. Tme bands Weekly Weekly detals Specal event Specal event detals Actons Notfcatons Notfcaton detals Scheduled actvtes Reports Data savng Scheduled actvty detals Report detals Detals Rules Scheduled rules Rule detals Scheduled rule detals I/O test Guardan Notfcatons Prorty 26

27 5. SCHEDULER ENG How to set scheduled rules Below s a step-by-step descrpton of how to turn off the lghts at 20:00 each workng day and turn them on agan n the mornng at 9:00. From the home page, enter the SCHEDULER RULE CONFIGURATION TIME BANDS DAILY menu: enter the daly tme bands for swtchng the lght off or on; n the example two tme bands have been created, called workng day (09:00-20:00) and workng nght (20:01-08:59). To set the nght-tme band 21:00-06:00, t must be dvded nto two bands: 21:00-23:59 and 00:00-06:00. From the TIME BANDS WEEKLY menu: now create the weekly lght On/Off tme bands; n the example two bands have been created relatng to day and nght (day= lghts on, nght= lghts off ), called workng week day and workng week nght, enterng frst the daly tme bands created prevously on the days from Monday to Frday (premses consdered closed Saturday & Sunday). 27

28 5. SCHEDULER Return to the RULE CONFIGURATION ACTIONS SCHEDULED ACTIVITIES menu: enter the desred actons (on the entre nstallaton or just on some devces, usng the opton for assgnng the actons to the GROUPS). Two actons have been created, lghts ON and lghts OFF, turnng the lghts on and off respectvely Then go to RULE CONFIGURATION SCHEDULED RULES : enter the new scheduled rules, that s, one that acts n the tme band when the lghts should be on, actvatng the acton that swtches the lghts on (ths rule wll be called lghts on (day) ) together wth another rule that swtches the lghts off, thus actvatng the lghts OFF acton (ths rule has been called lghts off (nght). In four steps, a scheduled actvty has been set that automatcally swtches the lghts on and off; the same procedure can be used to create other rules actng on the nstallaton (entre nstallaton or just some devces. 28

29 5. SCHEDULER ENG How to set the rules Below s a descrpton of how to set PlantWatchPRO to notfy a hghest prorty alarm actvated n the nght-tme tme band (21:00-08:00) va SMS. From the home page, enter the SCHEDULER RULE CONFIGURATION TIME BANDS DAILY menu: create a tme band that goes from 21:00 to 08:00; n the example ths has been called nght. Remember that to set the nght-tme band 21:00-08:00 t must be dvded nto 21:00-23:59 00:00-08:00. Return to TIME BANDS WEEKLY : create a weekly tme band n whch the nght daly band s appled every day of the week; ths weekly tme band has been called every nght. Return to the RULE CONFIGURATION ACTIONS NOTIFICATIONS menu: enter the notfcaton acton send SMS, selectng from the SMS lst the telephone number of mantenance tech. X to send the SMS to as the only notfcaton channel. 29

30 5. SCHEDULER Return to the RULE CONFIGURATION RULES menu: now create a rule (called nght SMS ), applyng a DELAY of one mnute (enter 1 n the correspondng feld); from ALARM PRIORITY choose Hghest, from TIME BANDS, every nght (band prevously created n the correspondng menu) and fnally, from ACTION send SMS. Wth these settngs, as soon as a hghest prorty alarm s actvated, on any nght of the week, PlantWatchPRO wats one mnute and, f wthn ths tme nterval the alarm has not concluded, notfcaton of a hghest prorty alarm wll be sent va SMS to mantenance tech. X". 30

31 5. SCHEDULER ENG How to confgure the Guardan program Below s a descrpton of how to send a fax to a certan number f a hghest prorty alarm s actvated on a feld devce. From the home page, enter the SCHEDULER PHONE BOOK FAX menu, and enter the fax number to send the notfcaton to, wth a short descrpton Return to the SCHEDULER and enter the GUARDIAN NOTIFICATIONS menu, choose the fax number set prevously n the PHONE BOOK from the lst. Return to the GUARDIAN and enter the ALARM PRIORITY menu, select the type of alarm to be managed usng the Guardan program; n ths case select Hghest, to have the alarms wth the hghest prorty sgnalled va fax f the system does not manage them wthn 30 mnutes ( 30 mn s the tme set by the user). 31

32 5. SCHEDULER How to confgure emal Below s a step-by-step descrpton of how to confgure the parameters to allow PlantWatchPRO to send emal. From the home page enter the SCHEDULER I/O CONFIGURATION CONFIGURATION menu to access the parameter confguraton screen Under SENDER enter the e-mal address of the sender of the e-mal The USER, PASSWORD and SMTP felds should be completed wth the data suppled by the ISP. Warnng: the IP address, and not the URL, must be entered n the SMTP feld. Ths confguraton should be completed by qualfed personnel (systems admnstrators) Then enter the NUMBER OF ATTEMPTS to be made and the delay between attempts (RETRY AFTER MINUTES feld) Under TYPE choose whether to access va LAN or va modem (Provder) If accessng va modem (.e. Provder has been chosen n the TYPE feld), the Dal- Up also needs to be confgured: From the home page enter thescheduler I/O CONFIGURATION CONFIGURATION DIAL-UP menu and enter the telephone NUMBER to connect to when sendng e-mal, the USERNAME and PASSWORD. Warnng: the telephone NUMBER, USERNAME and PASSWORD used on the Dal-Up confguraton page are suppled by the ISP After havng completed these steps, make sure that the e-mal communcaton channel has been confgured correctly, usng the specal functon: from the home page go to SCHEDULER I/O TEST and choose the desred e-mal CHANNEL (e-mal address prevously entered n SCHEDULER PHONE BOOK 32

33 5. SCHEDULER ENG How to create a scheduled rule to download a report from PlantWatchPRO Below s the procedure for creatng a schedule rule to save a HACCP report to a USB memory key nserted n the frst slot at a set tme. Frstly a tme band and a HACCP report need to be created, as shown prevously. Then: From the home page, access SCHEDULER RULE CONFIGURATION ACTIONS DATA SAVING Add a new acton, enter a descrpton (e.g. HACCP report), select the report created prevously to be downloaded and USB channel 1. Confrm and n the DURATION/FREQUENCY feld select the desred combnaton (1 day/30 mnutes), then select confrm to save From the home page, access SCHEDULER RULE CONFIGURATION SCHEDULED RULES Add a new scheduled rule, enter a descrpton (Download report), select a tme band (band 1) and the prevously saved acton. Save agan and reload the confguraton. The rule saved wll download the report to the selected USB channel at the tme set n the tme band 33

34 5. SCHEDULER By default, a daly scheduled rule s set that downloads a HACCP report every day, wth a frequency of 30 mnutes, relatng to the prevous day. Ths rule s dsabled, to enable t access SCHEDULER RULE CONFIGURATION SCHEDULED RULES, select the ALL_HACCP rule, select the Enabled opton and then save and reload the confguraton 34

35 35 ENG 6. Condtons for correct confguraton Important: Strctly follow the connecton dagrams shown n the user manual and the nstructons provded. CAREL cannot be held lable for malfunctons, breakages, accdents or anythng else due to unawareness of or falure to heed the followng nstructons. Correct operaton of the nstrument s only guaranteed f the frmware and software reman unchanged. Connectvty and perpherals The supervsory system can be connected to external perpherals (prnter, GSM modem etc.), as long as such perpherals have been approved by CAREL. The supervsory system must be able to send notfcatons va the set channels: relay, emal, fax, SMS, remote algnment. For ths purpose, the system must be connected to a dedcated analogue telephone lne or a LAN. In the latter case, the customer must check the network confguraton so as to make sure that the system can perform the notfcaton actons. Alternatvely, the system can be connected to a CARELapproved external GSM modem. For each notfcaton (e.g. sendng an alarm sgnal to three dfferent recpents va e-mal), a test must be performed for each ndvdual recpent, so as to verfy correct system confguraton (the e-mal address or mal server confguraton may be wrong). To run the tests, follow the notfcaton test procedure descrbed n the user manual. For notfcatons va SMS, make sure that the GSM modem connected to PlantWatchPRO can effectvely send SMS messages (e.g. check sgnal coverage, make sure the SIM has credt, check correct operaton of the modem and the connecton to PlantWatchPRO.). For notfcatons va fax, make sure that the recevng fax applance s correctly connected to the telephone lne, s swtched on and has enough toner and paper to receve the fax notfcatons. The nternatonal modem settngs must be confgured n accordance wth the country where the unt s nstalled. Check compatblty between the remote and local modems, by runnng a communcaton test. Safety warnngs For adequate protecton of the systems aganst any possble problems that may arse, two dfferent physcal communcaton channels should be used (e.g. PSTN and GSM modem, or ADSL and relay) so that the alarm sgnals can be sent and receved wth certanty. Alternatvely, a guaranteed Ethernet connecton n a company network can be used. To check correct operaton of PlantWatchPRO and the communcaton channel, enable the sgn-oflfe sgnal, settng a frequency compatble wth the mportance of the system beng montored and the damage that may occur due to malfunctons (e.g. every 4 hours for refrgeraton systems). The guardan component of the software (see the manual for further detals) should be confgured so that ths notfes any problem stuatons (n partcular, alarms not managed). Guardan notfcatons must be sent va all physcal channels avalable and enabled (f a notfcaton channele.g. fax - s not workng correctly, the guardan must be able to use another e.g. SMS wth GSM modem so that safety of the system s always ensured).

36 36

37

38

39

40 CAREL INDUSTRIES Hqs Va dell Industra, Brugne - Padova (Italy) Tel. (+39) Fax (+39) e-mal: CAREL@CAREL.com - Agenza / Agency: