In this section, user interface of the device, how to access to the parameters, description of the parameters are explained.

Transcription

1

2 ABOUT INSTRUCTION MANUAL Instructon manual of ESM-4450 Process Controller conssts of two man sectons. Explanaton of these sectons are below. Also, there are other sectons whch nclude order nformaton and techncal specfcatons of the devce. All ttles and page numbers n nstructon manual are n CONTENTS secton. User can reach to any ttle wth secton number. Installaton: In ths secton, physcal dmensons of the devce, panel mountng, electrcal wrng, module mountng to the devce, physcal and electrcal nstallaton of the devce to the system are explaned. Operaton and Parameters: In ths secton, user nterface of the devce, how to access to the parameters, descrpton of the parameters are explaned. Also n these sectons, there are warnngs to prevent serous njury whle dong the physcal and electrcal mountng or usng the devce. Explanaton of the symbols whch are used n these sectons are gven below. Ths shock. symbol s used for safety warnngs. User must pay attenton to these warnngs. Ths symbol s used to determne the dangerous stuatons as a result of an electrc User must pay attenton to these warnngs defntely. Ths symbol s used to determne the mportant notes about functons and usage of the devce. In parameters secton, for makng relevant parameters to be actve, determned module must be nstalled to Module-1 or Module-2 socket. 2

3 CONTENTS 1.PREFACE GENERAL SPECIFICATIONS 1.2 ORDERING INFORMATION 1.3 WARRANTY 1.4 MAINTENANCE 2.INSTALLATION... Page GENERAL DESCRIPTION 2.2 DIMENSIONS 2.3 PANEL CUT-OUT 2.4 ENVIRONMENTAL RATINGS 2.5 PANEL MOUNTING 2.6 INSTALLATION FIXING CLAMP 2.7 REMOVING FROM THE PANEL 3.ELECTRICAL WIRINGS TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS 3.2 ELECTRICAL WIRING DIAGRAM 3.3 SUPPLY VOLTAGE INPUT CONNECTION OF THE DEVICE 3.4 PROCESS INPUT CONNECTION TC (THERMOCOUPLE) CONNECTION RTD CONNECTION PROCESS INPUT CONNECTION OF SERIAL TRANSMITTERS WITH CURRENT OUTPUT (LOOP POWERED) PROCESS INPUT CONNECTION OF 3-WIRE TRANSMITTERS WITH CURRENT OUTPUT CONNECTION OF TRANSMITTERS WITH VOLTAGE OUTPUT TO PROCESS INPUT 3.5 RELAY OUTPUT CONNECTION 3.6 GALVANIC ISOLATION TEST VALUES OF ESM-4450 PROCESS CONTROLLER AND INPUT/OUTPUT MODULES 4.DEFINITIONS AND SPECIFICATIONS OF MODULES INPUT MODULES EMI-400 DIGITAL INPUT MODULE EMI-410 0/4...20mA CURRENT INPUT MODULE EMI A CT INPUT MODULE EMI-430 TC OR mV INPUT MODULE EMI-440 PT-100 INPUT MODULE EMI V INPUT MODULE 4.2 OUTPUT MODULES EMO-400 RELAY OUTPUT MODULE EMO-410 SSR DRIVER OUTPUT MODULE EMO-420 DIGITAL (TRANSISTOR) OUTPUT MODULE EMO-430 0/4...20mA CURRENT OUTPUT MODULE 4.3 INSTALLING AND PULLING OUT INPUT/OUTPUT MODULES 4.4 TO STICK INPUT/OUTPUT MODULES LABELS TO THE DEVICE 5.CONNECTION TERMINALS OF INPUT/OUTPUT MODULES AND CONNECTION WIRINGS CONNECTION WIRINGS FOR INPUT MODULES CONNECTION OF EMI-400 DIGITAL INPUT MODULE CONNECTION OF 3-WIRE TRANSMITTER TO EMI-410 0/4...20mA CURRENT INPUT MODULE CONNECTION OF SERIAL TRANSMITTER (LOOP POWERED) TO EMI-410 0/4...20mA CURRENT INPUT MODULE CURRENT TRANSFORMER CONNECTION TO EMI A CT INPUT MODULE CONNECTION OF EMI-430 TC OR mV INPUT MODULE USING EMI-430 TC or mV INPUT MODULE AS mV INPUT Page 6 Page 14 Page 21 Page 30 3

4 5.1.7 CONNECTION OF EMI-440 PT-100 INPUT MODULE CONNECTION OF EMI V INPUT MODULE 5.2 CONNECTION WIRINGS FOR OUTPUT MODULES EMO-400 RELAY OUTPUT MODULE CONNECTION EMO-410 SSR DRIVER MODULE CONNECTION EMO-420 DIGITAL (TRANSISTOR) OUTPUT MODULE CONNECTION EMO-430 0/4...20mA CURRENT OUTPUT MODULE CONNECTION TO GET V WITH EMO-430 0/4...20mA CURRENT OUTPUT MODULE 6.CONNECTIONS FOR RS-232 / RS-485 SERIAL COMMUNICATION... Page CABLE CONNECTION BETWEEN RS-232 TERMINAL OF THE DEVICE AND PC 6.2 CONNECTION FOR RS-485 SERIAL COMMUNICATION 6.3 INSTALLING RS-232 / RS-485 SERIAL COMMUNICATION MODULES TO THE DEVICE 7.DEFINITION OF FRONT PANEL AND ACCESSING TO THE PARAMETERS DEFINITION OF FRONT PANEL 7.2 OBSERVATION OF OPTIONAL MODULES AND SOFTWARE REVISION ON THE DISPLAYS 7.3 ADJUSTMENT OF PROCESS VALUE 7.4 ACCESSING TO THE OPERATOR MENU 7.5 ACCESSING TO THE TECHNICIAN MENU 7.6 ADJUSTMENT OF ALARM VALUES 7.7 CHANGING AND SAVING PARAMETER VALUES 8.PARAMETERS... Page OPERATOR PARAMETERS PROCESS AND ALARM PARAMETERS SELECTION OF PID TUNE AND OPERATION FORM FUNCTION SELECTION FOR TOP AND BOTTOM DISPLAY CONFIGURATION OF RAMP/SOAK FUNCTION AND STEP VALUES 8.2 TECHNICIAN PARAMETERS PROCESS INPUT TYPE AND RELEVANT PARAMETERS WITH PROCESS INPUT PID CONFIGURATION PARAMETERS MODULE-1 CONFIGURATION PARAMETERS MODULE-2 CONFIGURATION PARAMETERS OUTPUT-3 CONFIGURATION PARAMETERS GENERAL PARAMETERS PARAMETERS FOR CONFIGURATION OF SERIAL COMMUNICATION OPERATOR AND TECHNICIAN PASSWORDS Page 40 9.FAILURE MESSAGES IN ESM-4450 PROCESS CONTROLLERS... Page SPECIFICATIONS... Page 119 4

5 EU DECLARATION OF CONFORMITY Manufacturer Company Name : Emko Elektronk A.S. Manufacturer Company Address: DOSAB, Karanfl Sokak, No:6, Bursa, Turkye The manufacturer hereby declares that the product conforms to the followng standards and condtons. Product Name Model Number Type Number Product Category laboratory use : Process Controller : ESM-4450 : ESM-4450 : Electrcal equpment for measurement, control and Conforms to the followng drectves : 73 / 23 / EEC The Low Voltage Drectve as amended by 93 / 68 / EEC 89 / 336 / EEC The Electromagnetc Compatblty Drectve Has been desgned and manufactured accordng to the followng specfcatons EN :2001 EMC Generc Emsson Standard for the Industral Envronment EN :2001 EMC Generc Immunty Standard for the Industral Envronment EN :2001 Safety Requrements for electrcal equpment for measurement, control and laboratory use 5

6 1.Preface ESM seres process controllers are desgned for measurng and controllng temperature and any process value.they can be used n many applcatons wth ther unversal process nput, multfuncton control outputs, selectable alarm functons, seral communcaton unt and nput/output modules. Some applcaton felds and applcatons whch they are used are below: Applcaton Felds Applcatons Glass Motorzed valve control Plastc Profle Control Petro-Chemstry PID Process Control Textle Heater Falure detecton Automatve Machne producton ndustres 1.1 General Specfcatons ESM-4450 Power Supply Input Process Input Standard Unversal Supply Input V, 50/60Hz Low Voltage (optonal) Supply Input 24V 50/60Hz,24V, 12V Unversal Process Input TC,RTD, Voltage/Current Logc Input Module Analogue Input Modules TC, PT-100, Voltage/ Current Start and Stop functon for RAMP/SOAK Selecton of Manual / Automatc operaton for process control output - 2nd Sensor Input - Remote Set Input - Mult pont calbraton for Voltage/Current nput Optonal Input/Output Module-1 Optonal Input/Output Module-2 Standard Output-3(Relay Output) CT Input Module Relay, SSR Drver, Dgtal (Transstor), Current Output Module Control Output Alarm Output Re-Transmsson Output Control Output Alarm Output - Detecton of heater falure Heatng-Coolng Functon ON/OFF, PID Operaton Auto-Tune, Self-Tune Automatc/Manual Operaton Seral Communcaton Standard RS-232 Optonal RS-485 Baud Rate from 1200 to Modbus RTU Protocol 6

7 1.2 Orderng Informaton ESM-4450 (48x48 1/16 DIN) A A BC D E / FG HI / BC Input Type Scale 20 Confgurable (Table-1) Table-1 D E Output-1 1 Relay Output FG HI Table-1 BC Input Type(TC) 21 L,Fe Const DIN L,Fe Const DIN J,Fe CuN IEC584.1(ITS90) 24 J,Fe CuN IEC584.1(ITS90) 25 K,NCr N IEC584.1(ITS90) 26 K,NCr N IEC584.1(ITS90) 27 R,Pt13%Rh Pt IEC584.1(ITS90) 28 R,Pt13%Rh Pt IEC584.1(ITS90) 27 S,Pt10%Rh Pt IEC584.1(ITS90) 28 S,Pt10%Rh Pt IEC584.1(ITS90) 29 T,Cu CuN IEC584.1(ITS90) 30 T,Cu CuN IEC584.1(ITS90) 31 B,Pt30%Rh Pt6%Rh IEC584.1(ITS90) 32 B,Pt30%Rh Pt6%Rh IEC584.1(ITS90) 33 E,NCr CuN IEC584.1(ITS90) 34 E,NCr CuN IEC584.1(ITS90) 35 N,Ncrosl Nsl IEC584.1(ITS90) 36 N,Ncrosl Nsl IEC584.1(ITS90) 37 C, (ITS90) 38 C, (ITS90) BC Supply Voltage V (- 15%;+10% ) 50/60Hz 24 V (-15%;+10%) 50/60Hz 24V (-15%;+10%) 12 V (-15%;+10%) Customer (Maxmum 240V (- 15%;+10% ))50/60Hz Seral Communcaton None RS-232 RS-485 Input Type ( Voltage and Current) mv V V ma ma 1 / / Scale U V W Z Product Code - EMC-400 EMC-410 Module-1 None - Relay Output Module EMO-400 Product Code SSR Drver Output Module EMO-410 Dgtal (Transstor) Output Module Current Output Module ( 0/ ma ) EMO-420 EMO-430 Dgtal Input Module EMI-400 0/ ma Current Input Module EMI A CT Input Module EMI-420 TC or mV Input Module EMI-430 PT-100 Input Module EMI V Input Module EMI-450 Module-2 None Relay Output Module EMO-400 SSR Drver Output Module EMO-410 Dgtal (Transstor) Output Module EMO-420 Current Output Module ( 0/ ma ) Dgtal Input Module EMO-430 EMI-400 0/ ma Current Input Module EMI A CT Input Module EMI-420 TC or mV Input Module EMI-430 PT-100 Input Module EMI V Input Module EMI-450 BC Input Type(RTD) PT 100, IEC751(ITS90) PT 100, IEC751(ITS90) Scale() Product Code , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , , ,999.9 Scale() Scale() Scale() -200, , , , All order nformaton of ESM-4450 are gven on the table at left. User may form approprate devce confguraton from nformaton and codes that at the table and convert t to the orderng codes. Frstly, supply voltage then nput/output modules and other specfcatons must be determned. Please fll the order code blanks accordng to your needs. Please contact us, f your needs are out of the standards. EMI-400, EMO-410, EMO-420 and EMC-410 modules can not be used n 12V type. Symbol means Vac, Symbol means Vdc Symbol means Vac and Vdc 7

8 1.3 Warranty EMKO Elektronk warrants that the equpment delvered s free from defects n materal and workmanshp. Ths warranty s provded for a perod of two years. The warranty perod starts from the delvery date. Ths warranty s n force f duty and responsbltes whch are determned n warranty document and nstructon manual performs by the customer completely. 1.4 Mantenance Repars should only be performed by traned and specalzed personnel. Cut power to the devce before accessng nternal parts. Do not clean the case wth hydrocarbon-based solvents (Petrol, Trchlorethylene etc.). Use of these solvents can reduce the mechancal relablty of the devce. Use a cloth dampened n ethyl alcohol or water to clean the external plastc case. 8

9 2.Installaton Before begnnng nstallaton of ths product, please read the nstructon manual and warnngs below carefully. In package, - One pece unt - One pece mountng clamp - One pece nstructon manual A vsual nspecton of ths product for possble damage occured durng shpment s recommended before nstallaton. It s your responsblty to ensure that qualfed mechancal and electrcal techncans nstall ths product. If there s danger of serous accdent resultng from a falure or defect n ths unt, power off the system and separate the electrcal connecton of the devce from the system. The unt s normally suppled wthout a power swtch or a fuse. Use power swtch and fuse as requred. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. Never attempt to dsassemble, modfy or repar ths unt. Tamperng wth the unt may results n malfuncton, electrc shock or fre. Do not use the unt n combustble or explosve gaseous atmospheres. Durng the equpment s putted n hole on the metal panel whle mechancal nstallaton some metal burrs can cause njury on hands, you must be careful. Montage of the product on a system must be done wth t s own fxng clamps. Do not do the montage of the devce wth napproprate fxng clamps. Be sure that devce wll not fall whle dong the montage. It s your responsblty f ths equpment s used n a manner not specfed n ths nstructon manual. 9

10 ESM General Descrpton Product Label Termnal protecton cover F O1 O2 O3 REMO T E R A M P MAN A TO P r oces s Con tr o ller U Mountng Clamp Front Panel IP65 protecton NEMA 4X Panel surface (maxmum thckness 5mm / 0.2 nch) 2.2 Dmensons Maxmum 5mm / 0.2 nch ESM-4450 O1 O2 O3 Process Controller 48 mm / 1.89 nch 48mm / 1.89 nch 11.5 ± 1 mm /0.45 nch mm/ 4.11 nch 10

11 2.3 Panel Cut-Out 65 mm / 2.56 nch (mn) 46 mm / 1.81 nch (mn) 65 mm / 2.56 nch (mn) 46 mm / 1.81 nch (mn) 11

12 2.4 Envronmental Ratngs Operatng Condtons Operatng Temperature : 0 to 50 Max. Operatng Humdty : 90% Rh (non-condensng) Alttude : Up to 2000m. Forbdden Condtons: Corrosve atmosphere Explosve atmosphere Home applcatons (The unt s only for ndustral applcatons) 2.5 Panel Mountng 1 1-Before mountng the devce n your panel, make sure that the cut-out s of the rght sze. O1 O 2 O3 3 2-Check front panel gasket poston 3-Insert the devce through the cut-out. If the mountng clamp are on the unt, put out them before nsertng the unt to the panel. 2 Durng nstallaton nto a metal panel, care should be taken to avod njury from metal burrs whch mght be present. The equpment can loosen from vbraton and become dslodged f nstallaton parts are not properly tghtened. These precautons for the safety of the person who does the panel mountng. 12

13 2.6 Installaton Fxng Clamp O1 O2 1 2 The unt s desgned for panel mountng. 1-Insert the unt n the panel cut-out from the front sde. 2-Insert the mountng clamp from the rear sde of the unt and screw up the fxng screws untl the unt completely mmoble wthn the panel O 3 Montage of the unt to a system must be done wth t s own fxng clamps. Do not do the montage of the devce wth napproprate fxng clamps. Be sure that devce wll not fall whle dong the montage. 2.7 Removng from the Panel Before startng to remove the unt from panel, power off the unt and the related system. 2 1-Loosen the screws. 1 2-Lft the lockng tabs located on both the rght and left hand sdes and pull the fxng clamp from the devce whle holdng the unt n place. O1 O2 O3 3-Pull the unt through the front sde of the panel

14 3.Electrcal Wrngs You must ensure that the devce s correctly confgured for your applcaton. Incorrect confguraton could result n damage to the process beng controlled, and/or personal njury. It s your responsblty, as the nstaller, to ensure that the confguraton s correct. Devce parameters has factory default values. These parameters must be set accordng to the system s needs. Only qualfed personnel and techncans should work on ths equpment. Ths equpment contans nternal crcuts wth voltage dangerous to human lfe. There s severe danger for human lfe n the case of unauthorzed nterventon. Be sure to use the rated power supply voltage to protect the unt aganst damage and to prevent falure. Keep the power off untl all of the wrng s completed so that electrc shock and trouble wth the unt can be prevented. 3.1 Termnal Layout and Connecton Instructons 6 mm / nch Wre Sze: 18 AWG / 1 mm² Sold /Stranded screws termnal M Optonal connectons 0.5 Nm Torque 0.5 Nm Screw drver 0.8x3mm 14

15 3.2 Electrcal Wrng Dagram Electrcal wrng of the devce must be the same as Electrcal Wrng Dagram below to prevent damage to the process beng controlled and personnel njury. Unversal Process Input (TC, RTD, Voltage/Current) Sensor or Transmtter Supply Voltage 0-50mV 0-10V Output-3 Standard Relay Output 0-20mA 1 Pt-100 PTC, NTC TC V Max 50mA 4 C 5 NO 6 OUTPUT - 3 5A@250V P/N : ESM-4450 CAT II Communcaton Socket MODULE-1 MODULE Optonal Input/Output Module Termnals Relay, SSR Drver, Dgtal or Current Output Module Dgtal, Analogue and CT Input Modules Supply Voltage Input V (- 15%;+10% ) 50/60Hz - 6VA 24 V (-15%;+10%) 50/60Hz - 6VA 24V (-15%;+10%) - 6W 12 V (-15%;+10%) - 6W (It must be determned n order) Process nput, Analogue Module Inputs (EMI-410, EMI-430, EMI-440,EMI-450) and CT Module Input (EMI-420) are n CAT II class. 15

16 3.3 Supply Voltage Input Connecton of the Devce Connecton of Unversal Supply Voltage Input N 11 Supply Voltage V (-15%;+10%) 50/60 Hz Note-1 L 12 Connecton of Low Voltage 24 V Supply Voltage Input N 11 Note-2 External Fuse (1 A T) Power Supply Swtch Note-1 L 12 External Fuse (24V : 1 A T) (24V : 1 A T) Power Supply Swtch Supply Voltage 24V (-15%;+10%) 50/60Hz or 24V (-15%;+10%) Connecton of Low Voltage 12V Supply Voltage Input N ot e External Fuse (1 A T) Supply Voltage 12V (-15%;+10%) Power Supply Swtch Note-1 :There s an nternal 33R fusble flameproof resstor n V 50/60Hz There s an nternal 4R7 fusble flameproof resstor n 24V 50/60Hz, 24V and 12V Note-2 : L s (+), N s (-) for 24V Supply Voltage Supply voltage range must be determned n order. Whle nstallng the unt, supply voltage range must be controlled and approprate supply voltage must be appled to the unt. Controllng prevents damages n unt and system and possble accdents as a result of ncorrect supply voltage. There s no power swtch or fuse on the devce. So a power swtch and a fuse must be added to the supply voltage nput. Power swtch and fuse must be put to a place where user can reach easly. Power swtch must be two poled for seperatng phase and neutral. On/Off condton of power swtch s very mportant n electrcal connecton. On/Off condton of power swtch must be sgned for preventng the wrong connecton. External fuse must be on phase connecton n supply nput. External fuse must be on (+) lne connecton n supply nput. 16

17 3.4 Process Input Connecton TC (Thermocouple) Connecton TC Connect the wres wth the polarty as shown n the fgure left Always use compensaton wre correspondng to the thermocouple used. If present, the sheld must be connected to a proper ground. Input resstance s greater than 10M RTD Connecton Pt-100 Pt-100 Note 1 Note wre Pt-100 connecton (wth lne compensaton) (Max. Lne mpedance s 10 ) 2-wre Pt-100 connecton (wthout lne compensaton) Note 1 : In 3-wre system, use always cables of the same dameter (mn 1mm²) Always use wres of the same gauge and type whether a 2-wre or 3-wre system. Note 2 : Install a jumper between termnals 2 and 3 when usng a 2-wre RTD. Note 3 : If the dstance s longer than 10 meters, use 3-wre system Input resstance s greater than 10M 17

18 3.4.3 Process Input Connecton of Seral Transmtters wth Current Output (Loop Powered) Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source V Max. 50mA Transmtter 3 3 ma 4 PV 4 12 V Max. 50mA Transmtter ma PV External Power Supply Note 1 Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter. Input Resstance s 2R Process Input Connecton of 3-Wre Transmtters wth Current Output Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source ma 3 4 PV 4 12 V Max. 50mA Transmtter 12 V Max. 50mA ma PV Transmtter External Power Supply Note 1 Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter. Input Resstance s 2R7. 18

19 3.4.5 Connecton of Transmtters wth Voltage Output to Process Input Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source. 1 1 mv, V PV 4 12 V Max. 50mA Transmtter 12 V Max. 50mA mv, V PV Transmtter External Power Supply Note 1 Note 1 : External power supply must be selected accordng to supply voltage range and requred current for transmtter. Input resstance s greater than 10M for mV Input resstance s 43K for V 3.5 Relay Output Connecton C NO Devce 5 6 5A T Fuse Last Control Element (Contactor) Fuse L N Load Fuses must be selected accordng to the applcaton. 19

20 3.6 Galvanc Isolaton Test Values of ESM-4450 Process Controller and Input/Output Modules 2000V ( For ESM ) 500V ( For ESM ) 11 Supply Input Ground V Output-3 Relay Output V 2000V EMO-400 Relay Output Module V 2000V EMO-410 SSR Drver Module V 2000V EMO-420 Dgtal Output Module V 2000V 2000V EMO-430 0/4...20mA Current OutputModule EMI-400 Dgtal Input Module V 500V 2000V 2000V EMI-410 0/4...20mA Current Input Module EMI A CT Input Module V EMI-430 TC or mV Input Module V EMI-440 PT-100 Input Module V 2000V 2000V EMI V Input Module Analogue Inputs 12V Voltage Output V 2000V EMC-410 RS-485 Seral Communcaton Module EMC-400 RS-232 Seral Communcaton Module 500V 20

21 4.Defntons and Specfcatons of Modules ESM-4450 process controller s a modular product whch s desgned to operate wth addtonal analogue and dgtal nput/output unts whch user may need. Two nput/output modules can be plugged n the devce by the user. User may confgure the product for dfferent applcatons accordng to the system requrements wth the nput/output modules whch are descrbed n ths secton. Dmensons of Input/Output Modules 20.3mm 5mm 30.7mm 1.5mm 8.5mm 41.4mm 14mm 4.1 Input Modules EMI-400 Dgtal Input Module EMI-400 Dgtal nput module can be nstalled to Module-1 or Module-2 socket for usng the dgtal nput functons. Specfcatons of EMI-400 Dgtal Input Module Input Type :Normally Open Contact, NPN, PNP, Voltage Input ( 2 Volt and below 2 Volt s Logc 0, 4 Volt and above 4 Volt s Logc 1. Maxmum 30V can be appled) Dmensons :14x30.7x41.4mm Input Resstance : 2K2. Applcatons of EMI-400 Dgtal Input Module It s used to run, stop and pause ramp-soak functons n RAMP/SOAK applcatons. It can be used to operate the process control output as AUTOMATIC/MANUAL, start the PID tune operaton and latch cancelng. Detaled nformaton about functons of Dgtal Input Module functons are gven n parameters secton. For usng these functons EMI-400 Dgtal Input Module must be nstalled to Module-1 or Module-2 socket. Ths module can not be used n 12V type. 21

22 4.1.2 EMI-410 0/4...20mA Current Input Module EMI-410 0/4...20mA current nput module can be plugged n Module-1 or Module-2 socket to use as 2nd sensor nput, for measurng process value or for usng alarm functons whch are related to measured value. Also, remote set functon can be used by nstallng the module. Please refer to Secton or for detaled nformaton (, parameters) Specfcatons of EMI-410 0/4...20mA Current Input Module Input Type : 0/ ma Current Input Accuracy : 0.3% Dmensons : 14x30.7x41.4mm Input Resstance : 2R7. Applcatons of EMI-410 0/4...20mA Current Input Module It can be used to measure any process value and use t wth an alarm functon n applcatons that 2nd sensor nput s necessary. The current value (0/4...20mA ) on the module nput can be used as process set value when remote set functon s actvated and system can be controlled wth analogue sgnal (0/ ma ) whch s appled from remote pont. EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. Detaled nformaton about functons of EMI-410 0/4...20mA Current Input Module functons are gven n parameters secton. For usng these functons EMI-410 0/4...20mA Current Input Module must be nstalled to Module-1 or Module-2 socket. For usng EMI-410 0/4...20mA current nput module as mA, Or must be EMI A CT Input Module EMI A CT Input Module can be plugged n Module-1 or Module-2 socket for detectng heater falures n any applcatons. Two EMI-420 CT nput modules can not be plugged n Module-1 and Module- 2 socket at the same tme. Specfcatons of EMI A CT Input Module Input Type : 0...5A Accuracy : 2% FS Dmensons :14x30.7x41.4mm Input Resstance :23m. Applcatons of EMI A CT Input Module It can be used for observng heater current wth current transformer and detectng heatng falure. Detaled nformaton about functons of EMI A CT Input Module functons are gven n parameters secton. For usng these functons, EMI A CT Input Module must be nstalled to Module-1 or Module-2 socket. 22

23 4.1.4 EMI-430 TC (Thermocouple) or mV Input Module EMI-430 TC or mV nput module can be plugged n Module-1 or Module-2 socket to use as 2nd sensor nput, for measurng process value or for usng alarm functons whch are related to measured value. Also remote set functon can be used by pluggng ths module. Please refer to Secton or for detaled nformaton.(, parameters) EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. Specfcatons of EMI-430 TC or mV Input Module Please refer to Secton or for selecton of nput type and scale of TC nput type (L, J, K, R, S, T, B, E, N,C) Accuracy : 0.3% Dmensons :14x30.7x41.4mm Input Resstance :Greater than 10M Applcatons of EMI mV Input Module It can be used to measure any process value and use t wth an alarm functon n applcatons that 2nd sensor nput s necessary. The voltage value (0...50mV ) on the module nput can be used as process set value when "remote set" functon s actvated and system can be controlled wth analogue sgnal(0..50mv ) whch s appled from remote pont. Detaled nformaton about functons of EMI-430 TC or mV Input Module are gven n parameters secton. For usng these functons EMI-430 TC or mV Input Module must be nstalled to Module-1 or Module-2 socket. For usng EMI-430 TC or mV nput module as mV, or must be EMI-440 Pt-100 Input Module EMI-440 Pt-100 nput module can be plugged n Module-1 or Module-2 socket to use as 2nd sensor nput, for measurng process value or for usng alarm functons whch are related to measured value. Also remote set functon can be used by pluggng ths module. Please refer to Secton or for detaled nformaton.(, parameters) EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. Specfcatons of EMI-440 Pt-100 Input Module Please refer to Secton or for selecton of nput type and scale Accuracy : 0.5% Dmensons : 14x30.7x41.4mm Input Resstance : Greater than 10M 23

24 Applcatons of EMI-440 Pt-100 Input Module It can be used to measure any process value and use t wth an alarm functon n applcatons that 2nd sensor nput s necessary. The Pt-100 value on the module nput can be used as process set value when remote set functon s actvated and system can be controlled wth analogue sgnal whch s appled from remote pont. Detaled nformaton about functons of EMI-440 Pt-100 nput module are gven n PARAMETERS secton. For usng these functons EMI-440 Pt-100 nput module must be nstalled to Module-1 or Module-2 socket EMI V Input Module EMI V nput module can be plugged n Module-1 or Module-2 socket to use as 2nd sensor nput, for measurng process value or for usng alarm functons whch are related to measured value.(in some sectons t s defned as analogue nput module) Also remote set functon can be used by pluggng ths module. Please refer to Secton or for detaled nformaton.(, parameters) EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. Specfcatons of EMI V Input Module Accuracy : 0.3% Dmensons : 14x30.7x41.4mm Input Resstance :43K. Applcatons of EMI V Input Module It can be used to measure any process value and use t wth an alarm functon n applcatons that 2nd sensor nput s necessary. (0...10V ) value on module nput can be used as process set value when remote set functon s actvated and system can be controlled wth analogue sgnal(0...10v ) whch s appled from remote pont. Detaled nformaton about functons of EMI mV Input Module are gven n parameters secton. For usng these functons EMI mV Input Module must be nstalled to Module-1 or Module-2 socket. For usng EMI V nput module as V, Must be or 24

25 4.2 Output Modules EMO-400 Relay Output Module EMO-400 Relay output module can be plugged n Module-1 or Module-2 socket to use functons whch are defned for relay output. Specfcatons of EMO-400 Relay Output Module Output : 250V, Sngle Open Contact Dmensons : 14x30.7x41.4mm Electrcal Lfe : Operaton (Full Load) Applcatons of EMO-400 Relay Output Module It can be used wth heatng or coolng functons as process control output, as alarm output by programmable dfferent alarm functons, as logc output to transfer some datas on the devce to the system. These alternatves are explaned n parameters secton as logc output functon. Detaled nformaton about functons of EMO-400 Relay Output Module are gven n parameters secton. For usng these functons EMO-400 Relay Output Module must be nstalled to Module-1 or Module-2 socket EMO-410 SSR Drver Output Module EMO-410 SSR Drver Output Module can be plugged n Module-1 or Module-2 socket to use functons whch are defned for SSR drver output. Specfcatons of EMO-410 SSR Drver Module Output : Maxmum 20 ma, 15-18V ±10%, solated Dmensons : 14x30.7x41.4mm Applcatons of EMO-410 SSR Drver Output Module It can be used wth heatng or coolng functons as process control output, as alarm output by programmable dfferent alarm functons, as logc output to transfer some datas on the devce to the system. Note 1 : If short output perod s needed n a system, usng SSR Drver output module s recommended. ( Relay must not be used for short output perods because of lmted lfe of ther relay contact (open/close events)) Detaled nformaton about functons of EMO-410 SSR Drver Output Module are gven n parameters secton. For usng these functons EMO-410 SSR Drver Output Module must be nstalled to Module-1 or Module-2 socket. Ths module can not be used n 12V type. 25

26 4.2.3 EMO-420 Dgtal (Transstor) Output Module EMO-420 Dgtal (Transstor) Output Module can be plugged n Module-1 or Module-2 socket to use functons whch are defned for dgtal output. Specfcatons of EMO-420 Dgtal (Transstor) Output Module Output : Maxmum 40 ma, 15-18V ±10%, solated Dmensons : 14x30.7x41.4mm Applcatons of EMO-420 Dgtal (Transstor) Output Module It can be used wth heatng or coolng functons as process control output, as alarm output by programmable dfferent alarm functons, as logc output to transfer some datas on the devce to the system. These alternatves are explaned n parameters secton as logc output functon. Detaled nformaton about functons of EMO-420 Dgtal (Transstor) Output Module are gven n parameters secton. For usng these functons EMO-420 Dgtal (Transstor) Output Module must be nstalled to Module-1 or Module-2 socket EMO / mA Current Output Module EMO-430 0/4...20mA Current Output Module can be plugged n Module-1 or Module-2 socket to use functons whch are defned for current output. Specfcatons of EMO-430 0/4...20mA Current Output Module Output : 0/4...20mA current output Accuracy : 1% Note : To get V, 500 resstor wth 0.05% tolerance must be connected n parallel as a shunt resstor to module output (Please refer to Secton for detaled nformaton) Maxmum load mpedance : 600 Dmensons : 14x30.7x41.4mm Applcatons of EMO-430 0/4...20mA Current Output Module It can be used n heatng or coolng functons as process control output. Process value, dfference between process and set value or set value can be retransmtted to the system as mA or mA output. Retransmsson s explaned n parameters secton. Ths module can not be used n 12V type. Detaled nformaton about functons of EMO-430 Current Output Module are gven n parameters secton. For usng these functons EMO-430 0/4...20mA current Output Module must be nstalled to Module-1 or Module-2 socket. 26

27 4.3 Installng and Pullng Out Input/Output Modules Frst, detach all cable connectons from the devce and unnstall t from the panel. Suppress to the lock pns where top and bottom of the devce Pull the cover case wth your other hand from front panel to rear sde. Pull out the cover case from the devce Slde nput/output modules nto socket. Pull out the module from t s socket, nstead of ths module nstall the new one or other module user wants to use. Replace the cover case by takng care of the termnal numbers should be at rght poston. After addng or changng modules to the unt, these changes must be taken nto consderaton whle mountng of the unt to the system. If mountng s ncorrect, t can cause accdents to harm system, operator or person who does the mountng. Responsblty of these knd of harmful events belongs to the user. 27

28 4.4 To Stck Input/Output Modules Labels to the Devce Every module whch s plugged n Module-1 or Module-2 socket has labels for showng the relaton between connecton termnal and the devce. These labels are attached to empty boxes whch are separated for Module-1 and Module-2 on the devce. Labels for all modules and attachment places are shown below. Label whch descrbes termnal connecton of module that s plugged n Module-2 socket s attached to ths area. 7 0 to 50mV 0 to 10V 0 to 20mA Max.50mA 12 V Pt-100 PTC, NTC TC N L 100 to 240 V 50/60 Hz - 6VA MODULE-1 MODULE P/N : ESM-4450 CAT II OUTPUT-3 5A@250V C NC C NO 5 6 LABELS FOR INPUT MODULES Label whch descrbes termnal connecton of module that s plugged n Module-1 socket s attached to ths area. EMI-400 Dgtal Input Module Label for EMI-400 Dgtal Input Module 0/4 to 20mA EMI-410 Current Input Module Label for EMI-410 0/4...20mA Current Input Module 0 to 5A EMI-420 CT Input Module Label for EMI A CT Input Module - + TC or 0 to 50mV Input Module EMI-430 Label for EMI-430 TC or mV Input Module Pt-100 EMI-440 Pt-100 Input Module Label for EMI-440 Pt-100 Input Module to 10V Input Module EMI-450 Label for EMI V Input Module LABELS FOR OUTPUT MODULES C NO 3A@250V EMO-400 Relay Output Module Label for EMO-400 Relay Output Module Max. 20mA@18V EMO-410 SSR Drver Output Module Label for EMO-410 SSR Drver Module Max. 40mA@18V EMO-420 Dgtal Output Module Label for EMO-420 Dgtal Output Module 0/4 to 20mA EMO-430 Current Output Module Label for EMO-430 0/4...20mA Current Output Module 28

29 Example : If user nstalls EMO-400 Relay Output Module to Module-1 socket, EMO-430 0/4...20mA Current Output Module to Module-2 socket and attach the approprate labels on the devce vew wll be lke below : 7 C NO 8 3A@250V EMO-400 Relay Output Module MODULE /4 to 20mA EMO-430 Current Output Module MODULE N L 100 to 240 V 50/60 Hz - 6VA P/N : ESM-4450 CAT II 0 to 50mV 0 to 10V 0 to 20mA OUTPUT-3 5A@250V 1 2 Pt-100 PTC, NTC TC 3 12 V Max.50mA 4 5 C C NC NO 6 29

30 5. Connecton Termnals of Input/Output Modules and Connecton Wrngs Module-1 / Module-2 Optonal Input Modules 7 EMI-400 Dgtal Input Module 8 EMI-410 Current Input Module 0/4 to 20 ma 7 8 EMI-420 CT Input Module 0 to 5A 7 8 EMI-430 TC or 0 to 50mV Input Module EMI-440 Pt-100 Input Module Pt EMI to 10V Input Module 8 Module-1 Connecton Termnals Module-2 Connecton Termnals Module-1 / Module-2 Optonal Output Modules EMO-400 Relay Output Module 3A@250V EMO-410 SSR Drver Output Module Max. 20mA@18V EMO-420 Dgtal Output Module Max. 40mA@18V EMO-430 Current Output Module 0/4 to 20 ma 7 C NO Module-1 Connecton Termnals Module-2 Connecton Termnals 5.1 Connecton Wrngs for Input Modules Connecton of EMI-400 Dgtal Input Module Module-1 Module Swtch Swtch

31 5.1.2 Connecton of 3-Wre Transmtter to EMI-410 0/ ma Current Input Module Transmtter connecton by usng supply voltage on the devce Module-1 Module Transmtter connecton by usng external supply voltage source. Note-1 7 Output 7 4 PV 4 12 V Maxmum 50mA Current ma Transmtter Note-1 12 V Maxmum 50mA Current Output ma PV Transmtter External Power Supply Note 2 Module-2 Module Note-1 Current 9 Output 9 ma 4 PV 4 12 V Maxmum 50mA Transmtter Note-1 : There s nternal 2R7 shunt Note-1 12 V Maxmum 50mA Current Output ma PV Transmtter External Power Supply Note 2 Note 2 : External power supply must be selected accordng to power supply voltage range and requred current for transmtter. EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. 31

32 5.1.3 Connecton of Seral Transmtter(Loop Powered) to EMI-410 0/ ma Current Input Module Transmtter connecton by usng supply voltage on the devce Transmtter connecton by usng external supply voltage source. Module-1 Module Note-1 7 Output V Maxmum 50mA Current ma PV Transmtter Note V Maxmum 50mA Current Output ma PV Transmtter External Power Supply Note 2 Module-2 10 Module-2 10 Note V Maxmum 50mA Current Output ma PV Transmtter Note V Maxmum 50mA Current Output ma PV Transmtter External Power Supply Note 2 Note-1 : There s nternal 2R7 shunt Note 2 : External power supply must be selected accordng to power supply voltage range and requred current for transmtter. EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. 32

33 5.1.4 Current Transformer Connecton to EMI A CT Input Module Module-1 8 Current Transformer (CT) Load A 0.1 Module A Current Transformer (CT) Load Two EMI-420 CT nput modules can not be plugged n Module-1 and Module-2 socket at the same tme Connecton of EMI-430 TC (Thermocouple) or mV Input Module Module-1 Module TC 10 9 TC Connect the wres wth the polarty as shown above. Always use compensaton wre correspondng to the thermocouple used. If present, the sheld must be connected to a proper ground. EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. 33

34 5.1.6 Usng EMI-430 TC or mV Input Module as mV Input Module-1 Module mv mv 8 PV 10 PV Transmtter Transmtter By selectng Module-1 or Module-2 analogue nput confguraton parameter or And defnng calbraton ponts wth dual pont calbraton property, EMI-430 TC or mV module can be used as mV nput. EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme Connecton of EMI-440 PT-100 Input Module Module-1 8 Pt-100 Module-2 10 Pt There s no lne compensaton n PT-100 Input Module EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme Connecton of EMI V Input Module Module-1 Module V V 8 PV 10 PV Transmtter Transmtter EMI-410, EMI-430, EMI-440 or EMI-450 analogue nput modules can not be plugged-n Module-1 and Module-2 socket at the same tme. 34

35 5.2 Connecton Wrngs for Output Modules EMO-400 Relay Output Module Connecton Module-1 L N Module-2 L N C 7 3A T Fuse C 9 3A T Fuse Last Control Element (Contactor) Last Control Element (Contactor) NO 8 Fuse NO 10 Fuse Load Load Fuses must be selected accordng to the applcatons EMO-410 SSR Drver Module Connecton Module-1 8 Last Control Element (SSR) L N Module-2 10 Last Control Element (SSR) L N 7 9 Fuse Fuse V Max. 20mA Load V Max. 20mA Load Fuses must be selected accordng to the applcatons. 35

36 5.2.3 EMO-420 Dgtal (Transstor) Output Module Connecton Module-1 Module Load 9 Load V Maxmum 40mA V Maxmum 40mA EMO-430 0/ ma Current Output Module Connecton Module Other Devce Shunt (Max. 600 ) Module Other Devce Shunt (Max. 600 ) To Get V wth EMO-430 0/ ma Current Output Module Module-1 Other Devce V Output Shunt = Module-2 Other Devce V Output Shunt =

37 6.Connectons for RS-232 / RS-485 Seral Communcaton RS-232 Termnal Defntons RS-485 Termnal Defntons RX D- 2 TX 2 D GND Cable Connecton Between RS-232 Termnal of the Devce and PC ESM-4450 Cable Lenght must be max. 12 meters for 9600 baud rate PC (Personal Computer) 9 Pn DCON connecton RX TX GND RX TX GND ESM-4450 Cable Lenght must be max. 12 meters for 9600 baud rate PC (Personal Computer) 25 Pn DCON connecton RX TX GND TX RX GND

38 6.2 Connecton for RS-485 Seral Communcaton PC(Personal Computer) RS-232 RS-485 Convertor SLAVE-1 D+ Rt D- RS-232 Connecton Cable MASTER 32 termnal can be connected n RS- 485 lne D- D+ Rt resstor = 120 For communcaton connecton Twsted Par cable must be used Cable lenght can be maxmum 1000 meters n 9600 baud rate. SLAVE-2 When baud rate ncreases, cable lenght must decrease D- D SLAVE-N D- D Rt 38

39 6.3 Installng RS-232 / RS-485 Seral Communcaton Modules to the Devce Pull the cover case wth your hand through rear sde as explaned n Installng and Pullng Out Input/Output Modules secton. Pull the modules n Module-1 and Module-2 socket through rear sde. Separate supply card whch s at the bottom of the equpment by lftng the lockng tabs located on front panel. Pay attenton to cable connecton between top and bottom cards. Damages n ths cable makes the equpment not to work. RS-232 or RS-485 module s plugged nto socket sgned as A and B. Hold the equpment to be t s front panel s on your rght, communcaton socket s on your left and module connecton socket wth 5 termnals on above. Plug n module connecton socket wth 5 termnals to the socket on Top Card. Do the same thngs for termnal socket n bottom card and connecton socket wth 3 termnals. Plug n bottom card to the place n front panel. Install the modules whch are pulled out to Module-1 and Module-2 socket. Replace the cover case by takng care of the termnal numbers should be at rght poston. Top Card A B A Bottom Card Top Card RS-232 or RS-485 module B Bottom Card Top Card A RS-232 or RS-485 module B Bottom Card 39

40 7.Defnton of Front Panel and Accessng to the Parameters 7.1 Defnton of Front Panel LED ndcaton of :Centgrade Unt LED ndcaton of Fahrenhet Unt LED ndcaton of unts other than and LED ndcaton of SV, Process set value LED ndcaton of AT, Autotune s actve LED ndcaton of Output-1 Status LED ndcaton of Output-2 Status LED ndcaton of Output-3 Status LED ndcaton of Operaton wth Remote set value LED ndcaton of Ramp&Soak operaton s actve LED ndcaton of Manual operaton (For process output) LED ndcaton of Automatc operaton (For process output) ESM-4450 O1 SV O2 O3 AT Process Controller Dsplays Process Value (PV) and Parameter Dsplays Proses Set Value (SV) and Parameter For detaled nformaton; Please refer to Secton (Process and Alarm Set Parameters) and (Functon selecton for Top and Bottom Dsplay) Menu button Ths button s used to access to the all menus and to move up to another menu n the menu lst Note-1 Ths button s used to decrase the values and access to the menu pages Note-1 Ths button s used to ncrease the value and access to the menu pages Ths button s used to access to the process set value and use as OK button n program parameters. Note-1: If ncrement or decrement button s pressed for 5 seconds contnuously, ncrement and decrement number become 10, f ncrement or decrement button s pressed for 10 seconds contnuously, ncrement and decrement number become

41 7.2 Observaton of Optonal Modules and Software Revson on the Dsplays There are two sockets for pluggng optonal modules to the devce. These modules are recognzed by the devce automatcally. When the power s appled to the devce all led ndcators and dsplay segments are momentarly llumnated for testng. Software revson number of the controller on the bottom dsplay and module defnton codes on the top dsplay are momentarly llumnated. Module defnton codes and how to observe these codes of optonal modules n Module-1 and Module-2 socket are explaned below : Optonal Input/Output module code for Module-1 ESM-4450 Optonal Input/Output module code for Module-2 O1 O2 O3 SV AT Process Controller Relay Output Module (EMO-400) SSR Drver and Dgtal Output Module (EMO-410,EMO-420) 0/4...20mA Current Output Module (EMO-430) Dgtal Input Module (EMI-400) Analogue Input Module (EMI-410,EMI-430,EMI-440 or EMI-450) A CT Input Module (EMI-420) There s no module n Module-1 socket Relay Output Module (EMO-400) SSR Drver and Dgtal Output Module (EMO-410,EMO-420) 0/4...20mA Current Output Module (EMO-430) Dgtal Input Module (EMI-400) Analogue Input Module (EMI-410,EMI-430,EMI-440 or EMI-450) A CT Input Module (EMI-420) There s no module n Module-2 socket ESM-4450 O1 O2 O3 SV AT ru Revson Process Controller Revson number 41

42 When power on, dsplay of the devce s lke below: ESM-4450 ESM-4450 ESM-4450 O1 O2 O3 SV AT Process Controller O1 O2 O3 SV AT Process Controller O1 O2 O3 SV AT Process Controller Frst segments of top and bottom dsplays are tested Second segments of top and bottom dsplays are tested. Thrd segments of top and bottom dsplays are tested. ESM-4450 ESM-4450 ESM-4450 O1 O2 O3 SV AT Process Controller O1 O2 O3 SV AT Process Controller O1 O2 O3 SV AT Process Controller Fourth segments of top and bottom dsplays are tested. devce On top dsplay whch modules are plugged n Module-1 and Module-2 socket and on bottom dsplay revson number are shown. All leds are energsed. Above, there s EMO-410 SSR Drver Output module n Module-1 socket and EMO-400 Relay Output Module n Module-2 socket. Revson number s 10. Man operaton screen s shown If there s an unexpected stuaton whle openng the devce, power off the and nform a qualfed personnel. 42

43 7.3 Adjustment of Process Set Value Operaton Screen O1 SV O1 SV O1 SV OP3 AT OP3 AT OP3 AT When button s pressed SV LED flashes, set value s shown n bottom dsplay. Change set value wth ncrement and decrement buttons. Press menu button to ext wthout savng Set value. Press Set button for savng Set value. O1 SV O1 SV OP3 AT OP3 AT Operaton Screen Operaton Screen 43

44 7.4 Acessng to the Operator Menu The parameters have been dvded nto groups accordng to ther functons. Every group has a ttle and frstly user must determne the ttle (menu) for accessng to the parameters. Refer to the parameters secton for detaled nformaton about parameters. O1 OP3 SV AT Operaton Screen O1 OP3 SV AT Operator Menu Enterng Screen O1 OP3 SV AT When menu button s pressed, Operator Menu Enterng screen s shown. Operator Password Enterng Screen s shown by pressng button. Enter password wth ncrement and decrement buttons. When screen s shown, operator parameters can be seen by pressng button wthout enterng operator password. But parameters can not be changed. Please refer to Secton ( Operator and Techncan Passwords ) O1 SV OP3 AT Operator Password If Operator password s not 0, operator password enterng screen s shown Press the Enter button to confrm password Operator and techncan can access to ths menu. Operator and techncan can access to ths menu. Operator or techncan can access to the former menu by pressng menu changng back button O1 SV OP3 AT O1 SV OP3 AT LIST Menu Process and alarm set values are n SEt LýSt menu Operator or techncan can access to the followng menu by pressng menu changng next button RUN LIST Menu Operatng form selecton parameters are n run LýSt menu. Operator or techncan can access to the followng menu by pressng menu changng next button 44

45 Operator and techncan can access to ths menu O1 OP3 SV AT DÝSPLAY LIST Menu Ths menu determnes whch parameter s shown n top and bottom dsplay. Operator or techncan can access to the former menu by pressng menu changng back button Operator or techncan can access to the followng menu by pressng menu changng next button. Operator and techncan can access to ths menu O1 OP3 SV AT RAMP&SOAK Menu Confguraton of Ramp/Soak functon and step set value parameters are n ths menu. Operator or techncan can access to the former menu by pressng menu changng back button Operator or techncan can access to the followng menu by pressng menu changng next button. Operator and techncan can access to ths menu O1 SV LIST Menu LIST menu exsts after RAMP/SOAK menu. OP3 AT Operator or techncan can access to the former menu by pressng menu changng back button Press menu button to ext from MENU lst and turn to operaton screen. Contnue to press menu changng next and back buttons to change the menu page By pressng ENTER button, user can access to the menu page and to all parameters n ths menu page. 45

46 7.5 Accessng to the Techncan Menu The parameters have been dvded nto groups accordng to ther functons. Every group has a ttle and frstly user must determne the ttle (menu) for accessng to the parameters. Refer to the parameters secton for detaled nformaton about parameters. O1 OP3 SV AT Operaton Screen O1 OP3 SV AT Operator Menu Enterng Screen O1 OP3 SV AT When menu button s pressed, Operator Menu Enterng screen s shown. When changng menu next button s pressed Techncan Menu Enterng screen s shown. Techncan Menu Enterng Screen Techncan Password Enterng screen s accessed by pressng button. O1 SV OP3 AT If techncan password s not 0, techncan password enterng screen s shown O1 SV OP3 AT Techncan Password Press the Enter button to confrm password. Enter password wth ncrement and decrement buttons When screen s shown, techncan parameters can be seen by pressng button wthout enterng password. But parameters can not be changed. Please refer to Secton (Operator and Techncan Passwords) O1 SV OP3 AT PINP CONF Menu Confguraton parameters of process nput. Operator can not access to ths menu. Techncan can access to the followng menu by pressng menu changng next button. Operator can not access to ths menu. Techncan can access to the former menu by pressng changng menu back button. O1 SV OP3 AT PID CONF Menu Parameters about PID algorthm. Techncan can access to the followng menu by pressng menu changng next button. 46